Buildings.Examples.DualFanDualDuct.Controls

Information

Package Content

Name	Description
Examples	Example models to test the components
RoomMixingBox	Controller for room mixing box
CoolingCoilTemperatureSetpoint	Set point scheduler for cooling coil
HeatingCoilTemperatureSetpoint	Set point scheduler for heating coil
FanVFD	Controller for fan revolution

Buildings.Examples.DualFanDualDuct.Controls.RoomMixingBox

Information

Parameters

Type	Name	Default	Description
MassFlowRate	m_flow_min		Minimum mass flow rate [kg/s]

Connectors

Type	Name	Description
input RealInput	TRoo	Measured room temperature [K]
output RealOutput	yHot	Signal for hot air damper
output RealOutput	yCol	Signal for cold deck air damper
input RealInput	mAir_flow	Measured air mass flow rate into the room
input RealInput	TRooSetHea	Room temperature setpoint for heating [K]
input RealInput	TRooSetCoo	Room temperature setpoint for cooling [K]

Modelica definition

block RoomMixingBox "Controller for room mixing box"
  extends Modelica.Blocks.Interfaces.BlockIcon;
  parameter Modelica.SIunits.MassFlowRate m_flow_min "Minimum mass flow rate";
  Buildings.Controls.Continuous.LimPID conHea(
    yMax=1,
    xi_start=0.1,
    initType=Modelica.Blocks.Types.InitPID.InitialState,
    Td=60,
    yMin=0,
    controllerType=Modelica.Blocks.Types.SimpleController.PI,
    k=0.1,
    Ti=120) "Controller for heating";
  Buildings.Controls.Continuous.LimPID conCoo(
    yMax=1,
    reverseAction=true,
    Td=60,
    controllerType=Modelica.Blocks.Types.SimpleController.PI,
    k=0.1,
    Ti=120) "Controller for cooling (acts on damper)";
  Modelica.Blocks.Interfaces.RealInput TRoo(final quantity="ThermodynamicTemperature",
                                          final unit = "K", displayUnit = "degC", min=0) 
    "Measured room temperature";
  Modelica.Blocks.Interfaces.RealOutput yHot "Signal for hot air damper";
  Modelica.Blocks.Interfaces.RealOutput yCol "Signal for cold deck air damper";
  Modelica.Blocks.Interfaces.RealInput mAir_flow 
    "Measured air mass flow rate into the room";
  Buildings.Controls.Continuous.LimPID conFloRat(
    yMax=1,
    xi_start=0.1,
    Td=60,
    yMin=0,
    controllerType=Modelica.Blocks.Types.SimpleController.PI,
    k=0.1,
    Ti=120) "Controller for mass flow rate";
  Modelica.Blocks.Sources.Constant mAirSet(k=m_flow_min) 
    "Set point for minimum air flow rate";
  Buildings.Utilities.Math.SmoothMax smoothMaxHea(deltaX=0.01) 
    "Adds control signal for minimum flow rate of zone";
  Modelica.Blocks.Interfaces.RealInput TRooSetHea(unit="K") 
    "Room temperature setpoint for heating";
  Modelica.Blocks.Interfaces.RealInput TRooSetCoo(unit="K") 
    "Room temperature setpoint for cooling";
  Modelica.Blocks.Sources.RealExpression gaiCoo(y=
        Buildings.Utilities.Math.Functions.smoothLimit(
        (TRoo - TRooSetHea)/(TRooSetCoo - TRooSetHea),
        0,
        1,
        0.01)) "Gain for adding minimum flow rate to cooling signal";
  Modelica.Blocks.Sources.RealExpression gaiHea(y=1 - gaiCoo.y) 
    "Gain for adding minimum flow rate to cooling signal";
  Modelica.Blocks.Math.Product product;
  Modelica.Blocks.Math.Product product1;
  Buildings.Utilities.Math.SmoothMax smoothMaxCoo(deltaX=0.01) 
    "Adds control signal for minimum flow rate of zone";
equation 
  connect(mAir_flow, conFloRat.u_m);
  connect(conHea.y, smoothMaxHea.u1);
  connect(conHea.u_s, TRooSetHea);
  connect(conCoo.u_s, TRooSetCoo);
  connect(TRoo, conCoo.u_m);
  connect(TRoo, conHea.u_m);
  connect(conFloRat.y, product.u1);
  connect(product.y, smoothMaxHea.u2);
  connect(product.u2, gaiHea.y);
  connect(gaiCoo.y, product1.u1);
  connect(conFloRat.y, product1.u2);
  connect(smoothMaxHea.y, yHot);
  connect(product1.y, smoothMaxCoo.u1);
  connect(conCoo.y, smoothMaxCoo.u2);
  connect(smoothMaxCoo.y, yCol);
  connect(mAirSet.y, conFloRat.u_s);
end RoomMixingBox;

Buildings.Examples.DualFanDualDuct.Controls.CoolingCoilTemperatureSetpoint

Information

Parameters

Type	Name	Default	Description
Temperature	TOn		Setpoint during on [K]
Temperature	TOff		Setpoint during off [K]

Connectors

Type	Name	Description
ControlBus	controlBus
output RealOutput	TSet	Temperature set point

Modelica definition

block CoolingCoilTemperatureSetpoint 
  "Set point scheduler for cooling coil"
  extends Modelica.Blocks.Interfaces.BlockIcon;
  import Buildings.Examples.VAVReheat.Controls.OperationModes;
  parameter Modelica.SIunits.Temperature TOn "Setpoint during on";
  parameter Modelica.SIunits.Temperature TOff "Setpoint during off";
  Modelica.Blocks.Sources.RealExpression TSetPoi(y=if (mode.y ==
        OperationModes.occupied or mode.y == OperationModes.unoccupiedPreCool
         or mode.y == OperationModes.safety) then TOn else TOff) 
    "Air temperature setpoint";
  VAVReheat.Controls.ControlBus controlBus;
  Modelica.Blocks.Routing.IntegerPassThrough mode;
  Modelica.Blocks.Interfaces.RealOutput TSet "Temperature set point";
equation 
  connect(controlBus.controlMode, mode.u);
  connect(TSetPoi.y, TSet);

end CoolingCoilTemperatureSetpoint;

Buildings.Examples.DualFanDualDuct.Controls.HeatingCoilTemperatureSetpoint

Information

Parameters

Type	Name	Default	Description
Temperature	TOn		Setpoint during on [K]
Temperature	TOff		Setpoint during off [K]

Connectors

Type	Name	Description
ControlBus	controlBus
output RealOutput	TSet	Temperature set point

Modelica definition

block HeatingCoilTemperatureSetpoint 
  "Set point scheduler for heating coil"
  import Buildings.Examples.VAVReheat.Controls.OperationModes;
 extends CoolingCoilTemperatureSetpoint(TSetPoi(y=if (mode.y ==
        OperationModes.unoccupiedOff) then TOff else TOn));
end HeatingCoilTemperatureSetpoint;

Buildings.Examples.DualFanDualDuct.Controls.FanVFD

Information

Parameters

Type	Name	Default	Description
Real	xSet_nominal		Nominal setpoint (used for normalization)
Real	r_N_min	0.01	Minimum normalized fan speed

Connectors

Type	Name	Description
input RealInput	u	Connector of Real input signal
output RealOutput	y	Connector of Real output signal
ControlBus	controlBus
input RealInput	u_m	Connector of measurement input signal

Modelica definition

block FanVFD "Controller for fan revolution"
  extends Modelica.Blocks.Interfaces.SISO;
  import Buildings.Examples.VAVReheat.Controls.OperationModes;
  Buildings.Controls.Continuous.LimPID con(
    yMax=1,
    yMin=0,
    controllerType=Modelica.Blocks.Types.SimpleController.PI,
    Td=60,
    Ti=10) "Controller";
  Modelica.Blocks.Math.Gain gaiMea(k=1/xSet_nominal) 
    "Gain to normalize measurement signal";
  parameter Real xSet_nominal "Nominal setpoint (used for normalization)";
  VAVReheat.Controls.ControlBus controlBus;
  Modelica.Blocks.Routing.Extractor extractor(nin=6);
  Modelica.Blocks.Sources.Constant off(k=r_N_min) "Off signal";
  Modelica.Blocks.Sources.Constant on(k=1) "On signal";
  Modelica.Blocks.Math.Gain gaiSet(k=1/xSet_nominal) 
    "Gain to normalize setpoint signal";
  Modelica.Blocks.Interfaces.RealInput u_m 
    "Connector of measurement input signal";
  parameter Real r_N_min=0.01 "Minimum normalized fan speed";
  Modelica.Blocks.Continuous.FirstOrder firstOrder(
    initType=Modelica.Blocks.Types.Init.InitialState,
    y_start=r_N_min,
    T=60);
equation 
  connect(gaiMea.y, con.u_m);
  connect(con.y, extractor.u[OperationModes.occupied]);
  connect(con.y, extractor.u[OperationModes.unoccupiedWarmUp]);
  connect(con.y, extractor.u[OperationModes.unoccupiedPreCool]);
  connect(off.y, extractor.u[OperationModes.unoccupiedOff]);
  connect(off.y, extractor.u[OperationModes.safety]);
  connect(on.y, extractor.u[OperationModes.unoccupiedNightSetBack]);
  connect(controlBus.controlMode, extractor.index);
  connect(gaiSet.y, con.u_s);
  connect(u_m, gaiMea.u);
  connect(gaiSet.u, u);
  connect(extractor.y, firstOrder.u);
  connect(y, extractor.y);
end FanVFD;