Buildings.Rooms.Examples.BESTEST

Home > Modelica

Buildings.Rooms.Examples.BESTEST

BESTEST validation models

Information

This package contains the models that were used for the BESTEST validation (ANSI/ASHRAE 2007). The basic model from which all other models extend from is Buildings.Rooms.Examples.BESTEST.Case600FF.

All examples have a script that runs an annual simulation and plots the results with the minimum, mean and maximum value listed in the ANSI/ASHRAE Standard 140-2007.

The script compares the following quantities

For free floating cases, the annual hourly integrated minimum (and maximum) zone air temperature, and the annual mean zone air temperature.
For cases with heating and cooling, the annual heating and cooling energy, and the annual hourly integrated minimum (and maximum) peak heating and cooling power.

Note that in addition to the BESTESTs, the window model has been validated separately in Nouidui et al. (2012).

Implementation

Heating and cooling is controlled using the PI controller Buildings.Controls.Continuous.LimPID with anti-windup.

Hourly averaged values, and annual mean values, are computed using an instance of Modelica.Blocks.Math.Mean.

References

ANSI/ASHRAE. 2007. ANSI/ASHRAE Standard 140-2007, Standard Method of Test for the Evaluation of Building Energy Analysis Computer Programs.

Thierry Stephane Nouidui, Michael Wetter, and Wangda Zuo. Validation of the window model of the Modelica Buildings library. Proc. of the 5th SimBuild Conference, Madison, WI, USA, August 2012.

Extends from Modelica.Icons.ExamplesPackage (Icon for packages containing runnable examples).

Package Content

Name Description

Case600FF Basic test with light-weight construction and free floating temperature

Case600 Case 600FF, but with dual-setpoint for heating and cooling

Case610 Case 600 with south shading

Case620 Case 600, but with windows on East and West side walls

Case630 Case 620, but with added overhang and sidefins

Case640 Case 600, but with heating schedule

Case650FF Case 600, no heating, no cooling, and ventilation as in case 650

Case650 Case 600, but cooling based on schedule, night venting, and no heating

Case900FF Case 600FF, but with high thermal mass

Case900 Case 600, but with high thermal mass

Case920 Case 900, but with windows on East and West side walls

Case940 Case 900, but with heating schedule

Case950 Case 900, but cooling based on schedule, night venting, and no heating

Case950FF Case 900, but no heating, no cooling, and ventilation as in case 650

Case960 Case 600, but with an unconditioned sun-space

Data Data for BESTEST models

BaseClasses Package with base classes for Buildings.Rooms.Examples.BESTEST

nStaRef=6 Number of states in a reference material

Name	Description
Case600FF	Basic test with light-weight construction and free floating temperature
Case600	Case 600FF, but with dual-setpoint for heating and cooling
Case610	Case 600 with south shading
Case620	Case 600, but with windows on East and West side walls
Case630	Case 620, but with added overhang and sidefins
Case640	Case 600, but with heating schedule
Case650FF	Case 600, no heating, no cooling, and ventilation as in case 650
Case650	Case 600, but cooling based on schedule, night venting, and no heating
Case900FF	Case 600FF, but with high thermal mass
Case900	Case 600, but with high thermal mass
Case920	Case 900, but with windows on East and West side walls
Case940	Case 900, but with heating schedule
Case950	Case 900, but cooling based on schedule, night venting, and no heating
Case950FF	Case 900, but no heating, no cooling, and ventilation as in case 650
Case960	Case 600, but with an unconditioned sun-space
Data	Data for BESTEST models
BaseClasses	Package with base classes for Buildings.Rooms.Examples.BESTEST
nStaRef=6	Number of states in a reference material

Types and constants

  constant Integer nStaRef = 6 "Number of states in a reference material";

Buildings.Rooms.Examples.BESTEST.Case600FF

Basic test with light-weight construction and free floating temperature

Buildings.Rooms.Examples.BESTEST.Case600FF

Information

This model is used for the test case 600FF of the BESTEST validation suite. Case 600FF is a light-weight building. The room temperature is free floating.

Extends from Modelica.Icons.Example (Icon for runnable examples).

Parameters

Type Name Default Description

Angle S_ Buildings.HeatTransfer.Types... Azimuth for south walls [rad]

Angle E_ Buildings.HeatTransfer.Types... Azimuth for east walls [rad]

Angle W_ Buildings.HeatTransfer.Types... Azimuth for west walls [rad]

Angle N_ Buildings.HeatTransfer.Types... Azimuth for north walls [rad]

Angle C_ Buildings.HeatTransfer.Types... Tilt for ceiling [rad]

Angle F_ Buildings.HeatTransfer.Types... Tilt for floor [rad]

Angle Z_ Buildings.HeatTransfer.Types... Tilt for wall [rad]

Integer nConExtWin 1 Number of constructions with a window

Integer nConBou 1 Number of surface that are connected to constructions that are modeled inside the room

Generic matExtWal Exterior wall

Generic matFlo Floor

Generic roof Roof

StandardResultsFreeFloating staRes redeclare parameter Building... Reference results from ASHRAE/ANSI Standard 140

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal		Exterior wall
Generic	matFlo		Floor
Generic	roof		Roof
StandardResultsFreeFloating	staRes	redeclare parameter Building...	Reference results from ASHRAE/ANSI Standard 140

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case600FF 
  "Basic test with light-weight construction and free floating temperature"
  extends Modelica.Icons.Example;

  package MediumA = Buildings.Media.GasesConstantDensity.SimpleAir 
    "Medium model";
  parameter Modelica.SIunits.Angle S_=
    Buildings.HeatTransfer.Types.Azimuth.S "Azimuth for south walls";
  parameter Modelica.SIunits.Angle E_=
    Buildings.HeatTransfer.Types.Azimuth.E "Azimuth for east walls";
  parameter Modelica.SIunits.Angle W_=
    Buildings.HeatTransfer.Types.Azimuth.W "Azimuth for west walls";
  parameter Modelica.SIunits.Angle N_=
    Buildings.HeatTransfer.Types.Azimuth.N "Azimuth for north walls";
  parameter Modelica.SIunits.Angle C_=
    Buildings.HeatTransfer.Types.Tilt.Ceiling "Tilt for ceiling";
  parameter Modelica.SIunits.Angle F_=
    Buildings.HeatTransfer.Types.Tilt.Floor "Tilt for floor";
  parameter Modelica.SIunits.Angle Z_=
    Buildings.HeatTransfer.Types.Tilt.Wall "Tilt for wall";
  parameter Integer nConExtWin = 1 "Number of constructions with a window";
  parameter Integer nConBou = 1 
    "Number of surface that are connected to constructions that are modeled inside the room";
  inner Modelica.Fluid.System system;
  parameter Buildings.HeatTransfer.Data.OpaqueConstructions.Generic matExtWal(
    nLay=3,
    absIR_a=0.9,
    absIR_b=0.9,
    absSol_a=0.6,
    absSol_b=0.6,
    material={Buildings.HeatTransfer.Data.Solids.Generic(
        x=0.009,
        k=0.140,
        c=900,
        d=530,
        nStaRef=nStaRef),Buildings.HeatTransfer.Data.Solids.Generic(
        x=0.066,
        k=0.040,
        c=840,
        d=12,
        nStaRef=nStaRef),Buildings.HeatTransfer.Data.Solids.Generic(
        x=0.012,
        k=0.160,
        c=840,
        d=950,
        nStaRef=nStaRef)}) "Exterior wall";
  parameter Buildings.HeatTransfer.Data.OpaqueConstructions.Generic
                                                          matFlo(final nLay=
           2,
    absIR_a=0.9,
    absIR_b=0.9,
    absSol_a=0.6,
    absSol_b=0.6,
    material={Buildings.HeatTransfer.Data.Solids.Generic(
        x=1.003,
        k=0.040,
        c=0,
        d=0,
        nStaRef=nStaRef),Buildings.HeatTransfer.Data.Solids.Generic(
        x=0.025,
        k=0.140,
        c=1200,
        d=650,
        nStaRef=nStaRef)}) "Floor";
  Buildings.Rooms.MixedAir roo(
    redeclare package Medium = MediumA,
    hRoo=2.7,
    nConExtWin=nConExtWin,
    nConBou=1,
    nPorts=3,
    energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
    AFlo=48,
    datConBou(
      layers={matFlo},
      each A=48,
      each til=F_),
    datConExt(
      layers={roof,matExtWal,matExtWal,matExtWal},
      A={48,6*2.7,6*2.7,8*2.7},
      til={C_,Z_,Z_,Z_},
      azi={S_,W_,E_,N_}),
    nConExt=4,
    nConPar=0,
    nSurBou=0,
    linearizeRadiation=false,
    datConExtWin(
      layers={matExtWal},
      A={8*2.7},
      glaSys={window600},
      wWin={2*3},
      hWin={2},
      fFra={0.001},
      til={Z_},
      azi={S_}),
    lat=weaDat.lat) "Room model for Case 600";
  Modelica.Blocks.Sources.Constant qConGai_flow(k=80/48) "Convective heat gain";
  Modelica.Blocks.Sources.Constant qRadGai_flow(k=120/48) "Radiative heat gain";
  Modelica.Blocks.Routing.Multiplex3 multiplex3_1;
  Modelica.Blocks.Sources.Constant qLatGai_flow(k=0) "Latent heat gain";
  Buildings.BoundaryConditions.WeatherData.ReaderTMY3 weaDat(filNam=
        "Resources/weatherdata/DRYCOLD.mos");
  Modelica.Blocks.Sources.Constant uSha(k=0) 
    "Control signal for the shading device";
  Modelica.Blocks.Routing.Replicator replicator(nout=max(1,nConExtWin));
  Modelica.Thermal.HeatTransfer.Sources.FixedTemperature TSoi[nConBou](each T=
        283.15) "Boundary condition for construction";
  parameter Buildings.HeatTransfer.Data.OpaqueConstructions.Generic roof(nLay=3,
    absIR_a=0.9,
    absIR_b=0.9,
    absSol_a=0.6,
    absSol_b=0.6,
    material={Buildings.HeatTransfer.Data.Solids.Generic(
        x=0.019,
        k=0.140,
        c=900,
        d=530,
        nStaRef=nStaRef),Buildings.HeatTransfer.Data.Solids.Generic(
        x=0.1118,
        k=0.040,
        c=840,
        d=12,
        nStaRef=nStaRef),Buildings.HeatTransfer.Data.Solids.Generic(
        x=0.010,
        k=0.160,
        c=840,
        d=950,
        nStaRef=nStaRef)}) "Roof";
  Buildings.Rooms.Examples.BESTEST.Data.Win600
         window600(
    UFra=3,
    haveExteriorShade=false,
    haveInteriorShade=false) "Window";
  Buildings.HeatTransfer.Conduction.SingleLayer soil(
    A=48,
    material(
      x=2,
      k=1.3,
      c=800,
      d=1500,
      R=0),
    steadyStateInitial=true,
    T_a_start=283.15,
    T_b_start=283.75) "2m deep soil (per definition on p.4 of ASHRAE 140-2007)";
  Buildings.Fluid.Sources.MassFlowSource_T sinInf(
    redeclare package Medium = MediumA,
    m_flow=1,
    use_m_flow_in=true,
    use_T_in=false,
    use_X_in=false,
    use_C_in=false,
    nPorts=1) "Sink model for air infiltration";
  Buildings.Fluid.Sources.Outside souInf(redeclare package Medium = MediumA,
      nPorts=1) "Source model for air infiltration";
  Modelica.Blocks.Sources.Constant InfiltrationRate(k=-48*2.7*0.5/3600) 
    "0.41 ACH adjusted for the altitude (0.5 at sea level)";
  Modelica.Blocks.Math.Product product;
  Buildings.Fluid.Sensors.Density density(redeclare package Medium = MediumA) 
    "Air density inside the building";
  Buildings.BoundaryConditions.WeatherData.Bus weaBus;
  Modelica.Thermal.HeatTransfer.Sensors.TemperatureSensor TRooAir 
    "Room air temperature";
  Buildings.Fluid.FixedResistances.FixedResistanceDpM   heaCoo(
    redeclare package Medium = MediumA,
    allowFlowReversal=false,
    m_flow_nominal=48*2.7*0.41/3600*1.2,
    dp_nominal=1,
    linearized=true,
    from_dp=true) "Heater and cooler";
  replaceable parameter Buildings.Rooms.Examples.BESTEST.Data.StandardResultsFreeFloating
      staRes(
        minT( Min=-18.8+273.15, Max=-15.6+273.15, Mean=-17.6+273.15),
        maxT( Min=64.9+273.15,  Max=69.5+273.15,  Mean=66.2+273.15),
        meanT(Min=24.2+273.15,  Max=25.9+273.15,  Mean=25.1+273.15))
          constrainedby Modelica.Icons.Record 
    "Reference results from ASHRAE/ANSI Standard 140";
  Modelica.Blocks.Math.MultiSum multiSum(nu=1);
  Modelica.Blocks.Math.Mean TRooHou(f=1/3600, y(start=293.15)) 
    "Hourly averaged room air temperature";
  Modelica.Blocks.Math.Mean TRooAnn(f=1/86400/365, y(start=293.15)) 
    "Annual averaged room air temperature";
equation 
  connect(qRadGai_flow.y,multiplex3_1. u1[1]);
  connect(qLatGai_flow.y,multiplex3_1. u3[1]);
  connect(multiplex3_1.y, roo.qGai_flow);
  connect(roo.uSha, replicator.y);
  connect(qConGai_flow.y, multiplex3_1.u2[1]);
  connect(weaDat.weaBus, roo.weaBus);
  connect(uSha.y, replicator.u);
  connect(product.y, sinInf.m_flow_in);
  connect(density.port, roo.ports[1]);
  connect(density.d, product.u2);
  connect(weaDat.weaBus, weaBus);
  connect(TSoi[1].port, soil.port_a);
  connect(soil.port_b, roo.surf_conBou[1]);
  connect(weaBus, souInf.weaBus);
  connect(roo.heaPorAir, TRooAir.port);
  connect(souInf.ports[1], heaCoo.port_a);
  connect(heaCoo.port_b, roo.ports[2]);
  connect(sinInf.ports[1], roo.ports[3]);
  connect(multiSum.y, product.u1);
  connect(InfiltrationRate.y, multiSum.u[1]);

  connect(TRooAir.T, TRooHou.u);
  connect(TRooAir.T, TRooAnn.u);
end Case600FF;

Buildings.Rooms.Examples.BESTEST.Case600

Case 600FF, but with dual-setpoint for heating and cooling

Buildings.Rooms.Examples.BESTEST.Case600

Information

This model is used for the basic test case 600 of the BESTEST validation suite. Case 600 is a light-weight building with room temperature control set to 20°C for heating and 27°C for cooling. The room has no shade and a window that faces south.

Extends from Case600FF (Basic test with light-weight construction and free floating temperature).

Parameters

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal		Exterior wall
Generic	matFlo		Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case600 
  "Case 600FF, but with dual-setpoint for heating and cooling"
  extends Case600FF(
    redeclare Buildings.Rooms.Examples.BESTEST.Data.StandardResults staRes(
    annualHea(Min=4.296*3.6e9, Max=5.709*3.6e9, Mean=5.090*3.6e9),
    annualCoo(Min=-6.137*3.6e9, Max=-7.964*3.6e9, Mean=-6.832*3.6e9),
    peakHea(Min=3.437*1000, Max=4.354*1000, Mean=4.000*1000),
    peakCoo(Min=-5.965*1000, Max=-6.827*1000, Mean=-6.461*1000)));
  Controls.Continuous.LimPID           conHea(
    Td=60,
    initType=Modelica.Blocks.Types.InitPID.InitialState,
    Ti=300,
    controllerType=Modelica.Blocks.Types.SimpleController.PI,
    k=0.1) "Controller for heating";
  Controls.Continuous.LimPID           conCoo(
    Td=60,
    reverseAction=true,
    initType=Modelica.Blocks.Types.InitPID.InitialState,
    Ti=300,
    controllerType=Modelica.Blocks.Types.SimpleController.PI,
    k=0.1) "Controller for cooling";
  Modelica.Blocks.Math.Gain gaiHea(k=1E6) "Gain for heating";
  Modelica.Blocks.Math.Gain gaiCoo(k=-1E6) "Gain for cooling";
  Modelica.Blocks.Math.Sum sum1(nin=2);
  Modelica.Blocks.Routing.Multiplex2 multiplex2;
  Modelica.Thermal.HeatTransfer.Sources.PrescribedHeatFlow preHea 
    "Prescribed heat flow for heating and cooling";
  Modelica.Blocks.Continuous.Integrator EHea(
    k=1,
    initType=Modelica.Blocks.Types.Init.InitialState,
    y_start=0,
    u(unit="W"),
    y(unit="J")) "Heating energy in Joules";
  Modelica.Blocks.Continuous.Integrator ECoo(
    k=1,
    initType=Modelica.Blocks.Types.Init.InitialState,
    y_start=0,
    u(unit="W"),
    y(unit="J")) "Cooling energy in Joules";
  BaseClasses.DaySchedule TSetHea(table=[0.0,273.15 + 20]) "Heating setpoint";
  BaseClasses.DaySchedule TSetCoo(table=[0.0,273.15 + 27]) "Cooling setpoint";
  Modelica.Blocks.Math.Mean PHea(f=1/3600) "Hourly averaged heating power";
  Modelica.Blocks.Math.Mean PCoo(f=1/3600) "Hourly averaged cooling power";
equation 
  connect(TRooAir.T,conHea. u_m);
  connect(conCoo.u_m, TRooAir.T);
  connect(conHea.y,gaiHea. u);
  connect(conCoo.y,gaiCoo. u);
  connect(gaiHea.y,multiplex2. u1[1]);
  connect(gaiCoo.y,multiplex2. u2[1]);
  connect(multiplex2.y,sum1. u);
  connect(sum1.y,preHea. Q_flow);
  connect(EHea.u,gaiHea. y);
  connect(ECoo.u,gaiCoo. y);
  connect(TSetHea.y[1],conHea. u_s);
  connect(TSetCoo.y[1],conCoo. u_s);
  connect(PCoo.u,gaiCoo. y);
  connect(PHea.u,gaiHea. y);
  connect(preHea.port, roo.heaPorAir);
end Case600;

Buildings.Rooms.Examples.BESTEST.Case610

Case 600 with south shading

Buildings.Rooms.Examples.BESTEST.Case610

Information

This model is the case 610 of the BESTEST validation suite. Case 610 differs from case 600 in that the window has an overhang.

Implementation

Two overhangs have been added, one for each window, because each window only sees its own overhang.

Extends from Buildings.Rooms.Examples.BESTEST.Case600 (Case 600FF, but with dual-setpoint for heating and cooling).

Parameters

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal		Exterior wall
Generic	matFlo		Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case610 "Case 600 with south shading"
  extends Buildings.Rooms.Examples.BESTEST.Case600(
  roo(
     datConExtWin(
      ove(
        wR={4.5,0.5},
        wL={0.5,4.5},
        each dep=1,
        each gap=0.5))),
   staRes(
    annualHea(Min=4.355*3.6e9, Max=5.786*3.6e9, Mean=5.146*3.6e9),
    annualCoo(Min=-3.915*3.6e9, Max=-5.778*3.6e9, Mean=-4.964*3.6e9),
    peakHea(Min=3.437*1000, Max=4.354*1000, Mean=3.998*1000),
    peakCoo(Min=-5.689*1000, Max=-6.371*1000, Mean=-5.988*1000)));

end Case610;

Buildings.Rooms.Examples.BESTEST.Case620

Case 600, but with windows on East and West side walls

Buildings.Rooms.Examples.BESTEST.Case620

Information

This model is the case 620 of the BESTEST validation suite. Case 620 differs from case 600 in that the west and east facing walls have a window, but there is no window in the south facing wall.

Extends from Buildings.Rooms.Examples.BESTEST.Case600 (Case 600FF, but with dual-setpoint for heating and cooling).

Parameters

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal		Exterior wall
Generic	matFlo		Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case620 
  "Case 600, but with windows on East and West side walls"
  extends Buildings.Rooms.Examples.BESTEST.Case600(
  roo(
    nConExtWin=2,
    datConExtWin(
      layers={matExtWal, matExtWal},
      each A=6*2.7,
      glaSys={window600, window600},
      each wWin=3,
      each hWin=2,
      each fFra=0.001,
      each til=Z_,
      azi={W_,E_}),
    nConExt=3,
    datConExt(
      layers={roof,matExtWal,matExtWal},
      A={48,8*2.7,8*2.7},
      til={C_,Z_,Z_},
      azi={S_,S_,N_})),
   staRes(
    annualHea(Min=4.613*3.6e9, Max=5.944*3.6e9, Mean=5.407*3.6e9),
    annualCoo(Min=-3.417*3.6e9, Max=-5.004*3.6e9, Mean=-4.218*3.6e9),
    peakHea(Min=3.591*1000, Max=4.379*1000, Mean=4.062*1000),
    peakCoo(Min=-3.634*1000, Max=-5.096*1000, Mean=-4.343*1000)));

end Case620;

Buildings.Rooms.Examples.BESTEST.Case630

Case 620, but with added overhang and sidefins

Buildings.Rooms.Examples.BESTEST.Case630

Information

This model is case 630 of the BESTEST validation suite. Case 630 differs from case 620 in that the windows on the west and east walls have an overhang and side fins.

Extends from Buildings.Rooms.Examples.BESTEST.Case620 (Case 600, but with windows on East and West side walls).

Parameters

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal		Exterior wall
Generic	matFlo		Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case630 "Case 620, but with added overhang and sidefins"
  extends Buildings.Rooms.Examples.BESTEST.Case620(
  roo(
    datConExtWin(
      ove(
        each wR=0.0,
        each wL=0.0,
        each dep=1.0,
        each gap=0.5),
      sidFin(
        each h=0.5,
        each dep=1.0,
        each gap=0.0))),
   staRes(
    annualHea(Min=5.050*3.6e9, Max=6.469*3.6e9, Mean=5.783*3.6e9),
    annualCoo(Min=-2.129*3.6e9, Max=-3.701*3.6e9, Mean=-2.832*3.6e9),
    peakHea(Min=3.592*1000, Max=4.280*1000, Mean=4.006*1000),
    peakCoo(Min=-3.072*1000, Max=-4.116*1000, Mean=-3.626*1000)));

end Case630;

Buildings.Rooms.Examples.BESTEST.Case640

Case 600, but with heating schedule

Buildings.Rooms.Examples.BESTEST.Case640

Information

This model is used for the basic test case 640 of the BESTEST validation suite. Case640 is the same as Case600, but with the following modifications:

From 2300 hours to 0700 hours, heat = on if zone temperature is below 10°C
From 0700 hours to 2300 hours, heat = on if zone temperature is above 20°C
All hours, cool = on if zone temperature below 27°C
Otherwise, mechanical equipment is off.

Extends from Case600 (Case 600FF, but with dual-setpoint for heating and cooling).

Parameters

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal		Exterior wall
Generic	matFlo		Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case640 "Case 600, but with heating schedule"
  extends Case600(
    TSetHea(table=[      0, 273.15 + 10;
                    7*3600, 273.15 + 10;
                    7*3600, 273.15 + 20;
                   23*3600, 273.15 + 20;
                   23*3600,273.15 + 10;
                   24*3600,273.15 + 10]),
  staRes(
    annualHea(Min=2.751*3.6e9, Max=3.803*3.6e9, Mean=3.207*3.6e9),
    annualCoo(Min=-5.952*3.6e9, Max=-7.811*3.6e9, Mean=-6.592*3.6e9),
    peakHea(Min = 5.232*1000, Max = 6.954*1000, Mean = 6.031 * 1000),
    peakCoo(Min= -5.892*1000, Max = 6.776*1000, Mean= -6.410 * 1000)));

end Case640;

Buildings.Rooms.Examples.BESTEST.Case650FF

Case 600, no heating, no cooling, and ventilation as in case 650

Buildings.Rooms.Examples.BESTEST.Case650FF

Information

This model is used for the test case 650FF of the BESTEST validation suite. Case 650FF is identical to case 650, except that there is no heating and no cooling.

Extends from Case600FF (Basic test with light-weight construction and free floating temperature).

Parameters

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal		Exterior wall
Generic	matFlo		Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case650FF 
  "Case 600, no heating, no cooling, and ventilation as in case 650"
  extends Case600FF(
  staRes(
      minT( Min=-23.0+273.15, Max=-21.6+273.15, Mean=-22.7+273.15),
      maxT( Min=63.2+273.15, Max=68.2+273.15, Mean=64.7+273.15),
      meanT(Min=18.0+273.15, Max=19.6+273.15, Mean=18.7+273.15)),
  multiSum(nu=2));
  BaseClasses.DaySchedule vent(table=[      0, -1703.16/3600;
                                       7*3600, -1703.16/3600;
                                       7*3600,             0;
                                      18*3600,             0;
                                      18*3600, -1703.16/3600;
                                      24*3600, -1703.16/3600]) 
    "Ventilation air flow rate";
equation 
  connect(multiSum.u[2],vent.y[1]);

end Case650FF;

Buildings.Rooms.Examples.BESTEST.Case650

Case 600, but cooling based on schedule, night venting, and no heating

Buildings.Rooms.Examples.BESTEST.Case650

Information

This model is used for the test case 650 of the BESTEST validation suite. Case650 is the same as Case600, but with the following modifications:

From 1800 hours to 0700 hours, vent fan = on
From 0700 hours to 1800 hours, vent fan = off
Heating is always off
From 0700 hours to 1800 hours, cooling is on if zone temperature > 27°C, otherwise cool = off.
From 1800 hours to 0700 hours, cooling is always off.
Ventilation fan capacity is 1703.16 standard m³/h (in addition to specified infiltration rate).
No waste heat from fan.

Extends from Case600 (Case 600FF, but with dual-setpoint for heating and cooling).

Parameters

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal		Exterior wall
Generic	matFlo		Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case650 
  "Case 600, but cooling based on schedule, night venting, and no heating"
  extends Case600(
    TSetHea(table=[0, 273.15 -200]),
    TSetCoo(table=[      0, 273.15+100;
                    7*3600, 273.15+100;
                    7*3600, 273.15+27;
                   18*3600, 273.15+27;
                   18*3600, 273.15+100;
                   24*3600, 273.15+100]),
  staRes(
    annualHea(Min=0*3.6e9, Max=0*3.6e9, Mean=0*3.6e9),
    annualCoo(Min=-4.816*3.6e9, Max=-6.545*3.6e9, Mean=-5.482*3.6e9),
    peakHea(Min = 0*1000, Max = 0*1000, Mean = 0 * 1000),
    peakCoo(Min= -5.831*1000, Max = -6.679*1000, Mean= -6.321*1000)),
    gaiHea(k=0),
    multiSum(nu=2));

  BaseClasses.DaySchedule vent(table=[      0, -1703.16/3600;
                                       7*3600, -1703.16/3600;
                                       7*3600,             0;
                                      18*3600,             0;
                                      18*3600, -1703.16/3600;
                                      24*3600, -1703.16/3600]) 
    "Ventilation air flow rate";
equation 
  connect(multiSum.u[2], vent.y[1]);
end Case650;

Buildings.Rooms.Examples.BESTEST.Case900FF

Case 600FF, but with high thermal mass

Buildings.Rooms.Examples.BESTEST.Case900FF

Information

This model is used for the test case 900FF of the BESTEST validation suite. Case 900FF is a heavy-weight building. The room temperature is free floating.

Extends from Case600FF (Basic test with light-weight construction and free floating temperature).

Parameters

Type Name Default Description

Angle S_ Buildings.HeatTransfer.Types... Azimuth for south walls [rad]

Angle E_ Buildings.HeatTransfer.Types... Azimuth for east walls [rad]

Angle W_ Buildings.HeatTransfer.Types... Azimuth for west walls [rad]

Angle N_ Buildings.HeatTransfer.Types... Azimuth for north walls [rad]

Angle C_ Buildings.HeatTransfer.Types... Tilt for ceiling [rad]

Angle F_ Buildings.HeatTransfer.Types... Tilt for floor [rad]

Angle Z_ Buildings.HeatTransfer.Types... Tilt for wall [rad]

Integer nConExtWin 1 Number of constructions with a window

Integer nConBou 1 Number of surface that are connected to constructions that are modeled inside the room

Generic matExtWal extWalCase900 Exterior wall

Generic matFlo floorCase900 Floor

Generic roof Roof

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal	extWalCase900	Exterior wall
Generic	matFlo	floorCase900	Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case900FF "Case 600FF, but with high thermal mass"
  extends Case600FF(
    matExtWal = extWalCase900,
    matFlo =    floorCase900,
    staRes(
      minT( Min=-6.4+273.15, Max=-1.6+273.15, Mean=-4.2+273.15),
      maxT( Min=41.6+273.15, Max=44.8+273.15, Mean=43.1+273.15),
      meanT(Min=24.5+273.15, Max=25.9+273.15, Mean=25.2+273.15)));

  Buildings.Rooms.Examples.BESTEST.Data.ExteriorWallCase900
     extWalCase900 "Exterior wall";

  Buildings.Rooms.Examples.BESTEST.Data.FloorCase900
    floorCase900 "Floor";

end Case900FF;

Buildings.Rooms.Examples.BESTEST.Case900

Case 600, but with high thermal mass

Buildings.Rooms.Examples.BESTEST.Case900

Information

This model is used for the basic test case 900 of the BESTEST validation suite. Case 900 is a heavy-weight building with room temperature control set to 20°C for heating and 27°C for cooling. The room has no shade and a window that faces south.

Extends from Case600 (Case 600FF, but with dual-setpoint for heating and cooling).

Parameters

Type Name Default Description

Angle S_ Buildings.HeatTransfer.Types... Azimuth for south walls [rad]

Angle E_ Buildings.HeatTransfer.Types... Azimuth for east walls [rad]

Angle W_ Buildings.HeatTransfer.Types... Azimuth for west walls [rad]

Angle N_ Buildings.HeatTransfer.Types... Azimuth for north walls [rad]

Angle C_ Buildings.HeatTransfer.Types... Tilt for ceiling [rad]

Angle F_ Buildings.HeatTransfer.Types... Tilt for floor [rad]

Angle Z_ Buildings.HeatTransfer.Types... Tilt for wall [rad]

Integer nConExtWin 1 Number of constructions with a window

Integer nConBou 1 Number of surface that are connected to constructions that are modeled inside the room

Generic matExtWal extWalCase900 Exterior wall

Generic matFlo floorCase900 Floor

Generic roof Roof

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal	extWalCase900	Exterior wall
Generic	matFlo	floorCase900	Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case900 "Case 600, but with high thermal mass"
  extends Case600(
   matExtWal = extWalCase900,
   matFlo =    floorCase900,
   staRes(
    annualHea(Min=1.170*3.6e9, Max=2.041*3.6e9, Mean=1.745*3.6e9),
    annualCoo(Min=-2.132*3.6e9, Max=-3.415*3.6e9, Mean=-2.678*3.6e9),
    peakHea(Min=2.850*1000, Max=3.797*1000, Mean=3.506*1000),
    peakCoo(Min=-2.888*1000, Max=-3.871*1000, Mean=-3.390*1000)));

  Buildings.Rooms.Examples.BESTEST.Data.ExteriorWallCase900
     extWalCase900 "Exterior wall";

  Buildings.Rooms.Examples.BESTEST.Data.FloorCase900
    floorCase900 "Floor";

end Case900;

Buildings.Rooms.Examples.BESTEST.Case920

Case 900, but with windows on East and West side walls

Buildings.Rooms.Examples.BESTEST.Case920

Information

This model is the case 920 of the BESTEST validation suite. Case 920 differs from case 900 in that the west and east facing walls have a window, but there is no window in the south facing wall.

Extends from Buildings.Rooms.Examples.BESTEST.Case900 (Case 600, but with high thermal mass).

Parameters

Type Name Default Description

Angle S_ Buildings.HeatTransfer.Types... Azimuth for south walls [rad]

Angle E_ Buildings.HeatTransfer.Types... Azimuth for east walls [rad]

Angle W_ Buildings.HeatTransfer.Types... Azimuth for west walls [rad]

Angle N_ Buildings.HeatTransfer.Types... Azimuth for north walls [rad]

Angle C_ Buildings.HeatTransfer.Types... Tilt for ceiling [rad]

Angle F_ Buildings.HeatTransfer.Types... Tilt for floor [rad]

Angle Z_ Buildings.HeatTransfer.Types... Tilt for wall [rad]

Integer nConExtWin 1 Number of constructions with a window

Integer nConBou 1 Number of surface that are connected to constructions that are modeled inside the room

Generic matExtWal extWalCase900 Exterior wall

Generic matFlo floorCase900 Floor

Generic roof Roof

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal	extWalCase900	Exterior wall
Generic	matFlo	floorCase900	Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case920 
  "Case 900, but with windows on East and West side walls"
  extends Buildings.Rooms.Examples.BESTEST.Case900(
  roo(
    nConExtWin=2,
    datConExtWin(
      layers={matExtWal, matExtWal},
      each A=6*2.7,
      glaSys={window600, window600},
      each wWin=3,
      each hWin=2,
      each fFra=0.001,
      each til=Z_,
      azi={W_,E_}),
    nConExt=3,
    datConExt(
      layers={roof,matExtWal,matExtWal},
      A={48,8*2.7,8*2.7},
      til={C_,Z_,Z_},
      azi={S_,S_,N_})),
   staRes(
    annualHea(Min=3.313*3.6e9, Max=4.300*3.6e9, Mean=3.973*3.6e9),
    annualCoo(Min=-1.840*3.6e9, Max=-3.092*3.6e9, Mean=-2.552*3.6e9),
    peakHea(Min=3.308*1000, Max=4.061*1000, Mean=3.804*1000),
    peakCoo(Min=-2.385*1000, Max=-3.505*1000, Mean=-3.077*1000)));

end Case920;

Buildings.Rooms.Examples.BESTEST.Case940

Case 900, but with heating schedule

Buildings.Rooms.Examples.BESTEST.Case940

Information

This model is used for the basic test case 940 of the BESTEST validation suite. Case940 is the same as Case900, but with the following modifications:

From 2300 hours to 0700 hours, heat = on if zone temperature is below 10°C
From 0700 hours to 2300 hours, heat = on if zone temperature is above 20°C
All hours, cool = on if zone temperature below 27°C
Otherwise, mechanical equipment is off.

Extends from Case900 (Case 600, but with high thermal mass).

Parameters

Type Name Default Description

Angle S_ Buildings.HeatTransfer.Types... Azimuth for south walls [rad]

Angle E_ Buildings.HeatTransfer.Types... Azimuth for east walls [rad]

Angle W_ Buildings.HeatTransfer.Types... Azimuth for west walls [rad]

Angle N_ Buildings.HeatTransfer.Types... Azimuth for north walls [rad]

Angle C_ Buildings.HeatTransfer.Types... Tilt for ceiling [rad]

Angle F_ Buildings.HeatTransfer.Types... Tilt for floor [rad]

Angle Z_ Buildings.HeatTransfer.Types... Tilt for wall [rad]

Integer nConExtWin 1 Number of constructions with a window

Integer nConBou 1 Number of surface that are connected to constructions that are modeled inside the room

Generic matExtWal extWalCase900 Exterior wall

Generic matFlo floorCase900 Floor

Generic roof Roof

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal	extWalCase900	Exterior wall
Generic	matFlo	floorCase900	Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case940 "Case 900, but with heating schedule"
  extends Case900(
    TSetHea(table=[      0, 273.15 + 10;
                    7*3600, 273.15 + 10;
                    7*3600, 273.15 + 20;
                   23*3600, 273.15 + 20;
                   23*3600,273.15 + 10;
                   24*3600,273.15 + 10]),
    staRes(
      annualHea(Min=0.793*3.6e9, Max=1.411*3.6e9, Mean=1.160*3.6e9),
      annualCoo(Min=-2.079*3.6e9, Max=-3.241*3.6e9, Mean=-2.578*3.6e9),
      peakHea(Min=3.980*1000, Max=6.428*1000, Mean=5.494*1000),
      peakCoo(Min=-2.886*1000, Max=-3.871*1000, Mean=-1.340*1000)));

end Case940;

Buildings.Rooms.Examples.BESTEST.Case950

Case 900, but cooling based on schedule, night venting, and no heating

Buildings.Rooms.Examples.BESTEST.Case950

Information

This model is used for the test case 950 of the BESTEST validation suite. Case950 is the same as Case900, but with the following modifications:

From 1800 hours to 0700 hours, vent fan = on
From 0700 hours to 1800 hours, vent fan = off
Heating is always off
From 0700 hours to 1800 hours, cooling is on if zone temperature > 27°C, otherwise cool = off.
From 1800 hours to 0700 hours, cooling is always off.
Ventilation fan capacity is 1703.16 standard m³/h (in addition to specified infiltration rate).
No waste heat from fan.

Extends from Case900 (Case 600, but with high thermal mass).

Parameters

Type Name Default Description

Angle S_ Buildings.HeatTransfer.Types... Azimuth for south walls [rad]

Angle E_ Buildings.HeatTransfer.Types... Azimuth for east walls [rad]

Angle W_ Buildings.HeatTransfer.Types... Azimuth for west walls [rad]

Angle N_ Buildings.HeatTransfer.Types... Azimuth for north walls [rad]

Angle C_ Buildings.HeatTransfer.Types... Tilt for ceiling [rad]

Angle F_ Buildings.HeatTransfer.Types... Tilt for floor [rad]

Angle Z_ Buildings.HeatTransfer.Types... Tilt for wall [rad]

Integer nConExtWin 1 Number of constructions with a window

Integer nConBou 1 Number of surface that are connected to constructions that are modeled inside the room

Generic matExtWal extWalCase900 Exterior wall

Generic matFlo floorCase900 Floor

Generic roof Roof

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal	extWalCase900	Exterior wall
Generic	matFlo	floorCase900	Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case950 
  "Case 900, but cooling based on schedule, night venting, and no heating"
  extends Case900(
    TSetHea(table=[0, 273.15 -200]),
    TSetCoo(table=[      0, 273.15+100;
                    7*3600, 273.15+100;
                    7*3600, 273.15+27;
                   18*3600, 273.15+27;
                   18*3600, 273.15+100;
                   24*3600, 273.15+100]),
    staRes(
      annualHea(Min=0*3.6e9, Max=0*3.6e9, Mean=0*3.6e9),
      annualCoo(Min=-0.387*3.6e9, Max=-0.921*3.6e9, Mean=-0.605*3.6e9),
      peakHea(Min=0*1000, Max=0*1000, Mean=0*1000),
      peakCoo(Min=-2.033*1000, Max=-3.170*1000, Mean=-2.674*1000)),
    gaiHea(k=0),
    multiSum(nu=2));

  BaseClasses.DaySchedule vent(table=[      0, -1703.16/3600;
                                       7*3600, -1703.16/3600;
                                       7*3600,             0;
                                      18*3600,             0;
                                      18*3600, -1703.16/3600;
                                      24*3600, -1703.16/3600]) 
    "Ventilation air flow rate";
equation 
  connect(multiSum.u[2], vent.y[1]);
end Case950;

Buildings.Rooms.Examples.BESTEST.Case950FF

Case 900, but no heating, no cooling, and ventilation as in case 650

Buildings.Rooms.Examples.BESTEST.Case950FF

Information

This model is used for the test case 950FF of the BESTEST validation suite. Case 950FF is identical to case 950, except that there is no heating and no cooling.

Extends from Case900FF (Case 600FF, but with high thermal mass).

Parameters

Type Name Default Description

Angle S_ Buildings.HeatTransfer.Types... Azimuth for south walls [rad]

Angle E_ Buildings.HeatTransfer.Types... Azimuth for east walls [rad]

Angle W_ Buildings.HeatTransfer.Types... Azimuth for west walls [rad]

Angle N_ Buildings.HeatTransfer.Types... Azimuth for north walls [rad]

Angle C_ Buildings.HeatTransfer.Types... Tilt for ceiling [rad]

Angle F_ Buildings.HeatTransfer.Types... Tilt for floor [rad]

Angle Z_ Buildings.HeatTransfer.Types... Tilt for wall [rad]

Integer nConExtWin 1 Number of constructions with a window

Integer nConBou 1 Number of surface that are connected to constructions that are modeled inside the room

Generic matExtWal extWalCase900 Exterior wall

Generic matFlo floorCase900 Floor

Generic roof Roof

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal	extWalCase900	Exterior wall
Generic	matFlo	floorCase900	Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case950FF 
  "Case 900, but no heating, no cooling, and ventilation as in case 650"
  extends Case900FF(
  staRes(
      minT( Min=-20.2+273.15, Max=-18.6+273.15, Mean=-19.6+273.15),
      maxT( Min=35.5+273.15, Max=38.5+273.15, Mean=36.5+273.15),
      meanT(Min=14.0+273.15, Max=15.0+273.15, Mean=14.4+273.15)),
  multiSum(nu=2));

  BaseClasses.DaySchedule vent(table=[      0, -1703.16/3600;
                                       7*3600, -1703.16/3600;
                                       7*3600,             0;
                                      18*3600,             0;
                                      18*3600, -1703.16/3600;
                                      24*3600, -1703.16/3600]) 
    "Ventilation air flow rate";
equation 
  connect(multiSum.u[2],vent.y[1]);

end Case950FF;

Buildings.Rooms.Examples.BESTEST.Case960

Case 600, but with an unconditioned sun-space

Buildings.Rooms.Examples.BESTEST.Case960

Information

This model is used for the test case 960 of the BESTEST validation suite. Case 960 is a two zones building, whereas the south-facing zone is an unconditioned sun-space.

Extends from Buildings.Rooms.Examples.BESTEST.Case600 (Case 600FF, but with dual-setpoint for heating and cooling).

Parameters

Type	Name	Default	Description
Angle	S_	Buildings.HeatTransfer.Types...	Azimuth for south walls [rad]
Angle	E_	Buildings.HeatTransfer.Types...	Azimuth for east walls [rad]
Angle	W_	Buildings.HeatTransfer.Types...	Azimuth for west walls [rad]
Angle	N_	Buildings.HeatTransfer.Types...	Azimuth for north walls [rad]
Angle	C_	Buildings.HeatTransfer.Types...	Tilt for ceiling [rad]
Angle	F_	Buildings.HeatTransfer.Types...	Tilt for floor [rad]
Angle	Z_	Buildings.HeatTransfer.Types...	Tilt for wall [rad]
Integer	nConExtWin	1	Number of constructions with a window
Integer	nConBou	1	Number of surface that are connected to constructions that are modeled inside the room
Generic	matExtWal		Exterior wall
Generic	matFlo		Floor
Generic	roof		Roof

Connectors

Type Name Description

Bus weaBus

Type	Name	Description
Bus	weaBus

Modelica definition

model Case960 "Case 600, but with an unconditioned sun-space"
  extends Buildings.Rooms.Examples.BESTEST.Case600(
    roo(
    nConExt=4,
    datConExt(
      layers={roof,matExtWal,matExtWal,matExtWal},
      A={48,6*2.7,6*2.7,8*2.7},
      til={C_,Z_,Z_,Z_},
      azi={S_,W_,E_,N_}),
    nConExtWin=0,
      datConExtWin(A={0}, hWin={0}, wWin={0}),
    nSurBou=1,
    surBou(
      each A=8*2.7,
      each absIR=0.9,
      each absSol=0.6,
      each til=Buildings.HeatTransfer.Types.Tilt.Wall)),
    souInf(nPorts=2),
    staRes(
      annualHea(Min=2.311*3.6e9, Max=3.373*3.6e9, Mean=2.846*3.6e9),
      annualCoo(Min=-0.411*3.6e9, Max=-0.803*3.6e9, Mean=-0.618*3.6e9),
      peakHea(Min=2.410*1000, Max=2.863*1000, Mean=2.701*1000),
      peakCoo(Min=-0.953*1000, Max=-1.404*1000, Mean=-1.212*1000)));

  Buildings.HeatTransfer.Conduction.MultiLayer
    parWal(layers=matLayPar, A=8*2.7) "Partition wall between the two rooms";

  Buildings.HeatTransfer.Data.OpaqueConstructions.Brick120
    matLayPar(material={
        Buildings.HeatTransfer.Data.Solids.Generic(
        x=0.2,
        k=0.510,
        c=1000,
        d=1400)}) "Construction material for partition walls";

  Buildings.Rooms.Examples.BESTEST.Data.ExteriorWallCase900
     extWalCase900 "Exterior wall";

  Buildings.Rooms.Examples.BESTEST.Data.FloorCase900
    floorCase900 "Floor";

  Buildings.Rooms.MixedAir sunSpa(
    redeclare package Medium = MediumA,
    hRoo=2.7,
    nPorts=3,
    energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
    intConMod=Buildings.HeatTransfer.Types.InteriorConvection.Temperature,
    extConMod=Buildings.HeatTransfer.Types.ExteriorConvection.TemperatureWind,
    nConPar=0,
    nConExt=3,
    datConExt(
      layers={roof,extWalCase900,extWalCase900},
      A={8*2,2*2.7,2*2.7},
      til={C_,Z_,Z_},
      azi={S_,W_,E_}),
    nSurBou=1,
    surBou(
      each A=8*2.7,
      each absIR=0.9,
      each absSol=0.6,
      each til=Buildings.HeatTransfer.Types.Tilt.Wall),
    linearizeRadiation=false,
    nConExtWin=1,
    datConExtWin(
      layers={extWalCase900},
      A={8*2.7},
      glaSys={window600},
      wWin={2*3},
      hWin={2},
      fFra={0.001},
      til={Z_},
      azi={S_}),
    nConBou=1,
    datConBou(
      layers={floorCase900},
      each A=2*8,
      each til=F_),
    AFlo=16,
    lat=0.69464104229374) "Room model for sun-space";
  Modelica.Blocks.Sources.Constant qConGai_flow1(k=0) "Convective heat gain";
  Modelica.Blocks.Sources.Constant qRadGai_flow1(k=0) "Radiative heat gain";
  Modelica.Blocks.Routing.Multiplex3 multiplex3_2;
  Modelica.Blocks.Sources.Constant qLatGai_flow1(k=0) "Latent heat gain";
  Buildings.HeatTransfer.Conduction.SingleLayer soil1(
    material(
      x=2,
      k=1.3,
      c=800,
      d=1500,
      R=0),
    steadyStateInitial=true,
    A=16,
    T_a_start=283.15,
    T_b_start=283.75) "2m deep soil (per definition on p.4 of ASHRAE 140-2007)";
  Buildings.Fluid.Sources.MassFlowSource_T sinInf2(
    redeclare package Medium = MediumA,
    m_flow=1,
    use_m_flow_in=true,
    use_T_in=false,
    use_X_in=false,
    use_C_in=false,
    nPorts=1) "Sink model for sunspace infiltration";
  Modelica.Blocks.Sources.Constant InfiltrationRate1(k=-16*2.7*0.5/3600) 
    "0.41 ACH adjusted for the altitude (0.5 at sea level)";
  Modelica.Blocks.Math.Product product1;
  Buildings.Fluid.Sensors.Density density1(redeclare package Medium = MediumA) 
    "Air density inside the building";

  Modelica.Thermal.HeatTransfer.Sources.FixedTemperature TSoi1[nConBou](
    each T=283.15) "Boundary condition for construction";
  Fluid.FixedResistances.FixedResistanceDpM heaCoo1(
    redeclare package Medium = MediumA,
    allowFlowReversal=false,
    m_flow_nominal=48*2.7*0.41/3600*1.2,
    dp_nominal=1,
    linearized=true,
    from_dp=true) "Heater and cooler";
equation 
  connect(sunSpa.uSha, replicator.y);
  connect(parWal.port_a, roo.surf_surBou[1]);
  connect(parWal.port_b, sunSpa.surf_surBou[1]);
  connect(sunSpa.surf_conBou[1], soil1.port_b);
  connect(TSoi1[1].port, soil1.port_a);
  connect(weaDat.weaBus, sunSpa.weaBus);
  connect(qRadGai_flow1.y, multiplex3_2.u1[1]);
  connect(qConGai_flow1.y, multiplex3_2.u2[1]);
  connect(qLatGai_flow1.y, multiplex3_2.u3[1]);
  connect(multiplex3_2.y, sunSpa.qGai_flow);
  connect(InfiltrationRate1.y, product1.u1);
  connect(density1.d, product1.u2);
  connect(product1.y, sinInf2.m_flow_in);
  connect(heaCoo1.port_b, sunSpa.ports[1]);
  connect(sinInf2.ports[1], sunSpa.ports[2]);
  connect(density1.port, sunSpa.ports[3]);
  connect(souInf.ports[2], heaCoo1.port_a);
end Case960;

Automatically generated Tue Jan 8 08:31:55 2013.