model ASHRAE2006 "Variable air volume flow system with terminal reheat and ASHRAE 2006 control sequence serving five thermal zones" extends Buildings.Examples.VAVReheat.BaseClasses.PartialHVAC(amb(nPorts=3)); parameter Real ratVMinVAV_flow[numZon](each final unit="1") = {max(1.5* VZonOA_flow_nominal[i]/mCooVAV_flow_nominal[i]/1.2, 0.15) for i in 1:numZon} "Minimum discharge air flow rate ratio"; Controls.FanVFD conFanSup( xSet_nominal(displayUnit="Pa") = 410, r_N_min=yFanMin) "Controller for fan"; Controls.ModeSelector modeSelector; Controls.ControlBus controlBus; Controls.Economizer conEco( have_reset=true, have_frePro=true, VOut_flow_min=Vot_flow_nominal) "Controller for economizer"; Controls.RoomTemperatureSetpoint TSetRoo( final THeaOn=THeaOn, final THeaOff=THeaOff, final TCooOn=TCooOn, final TCooOff=TCooOff); Controls.DuctStaticPressureSetpoint pSetDuc( nin=5, pMin=50) "Duct static pressure setpoint"; Controls.RoomVAV conVAV[numZon]( ratVFloMin=ratVMinVAV_flow, ratVFloHea=mHeaVAV_flow_nominal ./ mCooVAV_flow_nominal) "Controller for terminal unit"; Buildings.Controls.OBC.CDL.Logical.Or or2; Controls.SupplyAirTemperature conTSup "Supply air temperature and economizer controller"; Controls.SupplyAirTemperatureSetpoint TSupSet "Supply air temperature set point"; Buildings.Fluid.Actuators.Dampers.Exponential damExh( from_dp=false, riseTime=15, dpFixed_nominal=5, redeclare package Medium = MediumA, m_flow_nominal=mAir_flow_nominal, dpDamper_nominal=5) "Exhaust air damper"; Controls.SystemHysteresis sysHysHea "Hysteresis and delay to switch heating on and off"; Controls.SystemHysteresis sysHysCoo "Hysteresis and delay to switch cooling on and off"; Buildings.Controls.OBC.CDL.Continuous.Switch swiFreStaPum "Switch for freeze stat of pump"; Buildings.Controls.OBC.CDL.Continuous.Switch swiFreStaVal "Switch for freeze stat of valve"; Buildings.Controls.OBC.CDL.Continuous.Sources.Constant yFreHeaCoi(final k=1) "Flow rate signal for heating coil when freeze stat is on"; Buildings.Controls.OBC.CDL.Continuous.MultiMin TRooMin( final nin=numZon, u(each final unit="K", each displayUnit="degC"), y(final unit="K", displayUnit="degC")) "Minimum room temperature"; Utilities.Math.Average TRooAve( final nin=numZon, u(each final unit="K", each displayUnit="degC"), y(final unit="K", displayUnit="degC")) "Average room temperature"; Controls.FreezeStat freSta "Freeze stat for heating coil"; Buildings.Controls.OBC.CDL.Routing.RealScalarReplicator TRooHeaSet(final nout= numZon) "Replicate room temperature heating setpoint"; Buildings.Controls.OBC.CDL.Routing.RealScalarReplicator TRooCooSet(final nout= numZon) "Replicate room temperature cooling setpoint"; equation connect(controlBus, modeSelector.cb); connect(TRooAve.y, controlBus.TRooAve); connect(TRet.T, conEco.TRet); connect(TSetRoo.controlBus, controlBus); connect(dpDisSupFan.p_rel, conFanSup.u_m); connect(pSetDuc.y, conFanSup.u); connect(conEco.VOut_flow, VOut1.V_flow); connect(occSch.tNexOcc, controlBus.dTNexOcc); connect(occSch.occupied, controlBus.occupied); connect(TOut.y, controlBus.TOut); connect(conEco.controlBus, controlBus); connect(modeSelector.yFan, conFanSup.uFan); connect(conFanSup.y, fanSup.y); connect(or2.u2, modeSelector.yFan); connect(VAVBox.y_actual, pSetDuc.u); connect(TSup.T, conTSup.TSup); connect(conTSup.yOA, conEco.uOATSup); connect(or2.y, conTSup.uEna); connect(modeSelector.yEco, conEco.uEna); connect(TMix.T, conEco.TMix); connect(controlBus, TSupSet.controlBus); connect(TSupSet.TSet, conTSup.TSupSet); connect(damRet.y, conEco.yRet); connect(damExh.y, conEco.yOA); connect(damOut.y, conEco.yOA); connect(damExh.port_a, TRet.port_b); connect(freSta.y, or2.u1); connect(conTSup.yHea, sysHysHea.u); connect(conTSup.yCoo, sysHysCoo.u); connect(sysHysCoo.y, valCooCoi.y); connect(sysHysCoo.yPum, pumCooCoi.y); connect(sysHysCoo.sysOn, modeSelector.yFan); connect(sysHysHea.sysOn, modeSelector.yFan); connect(yFreHeaCoi.y, swiFreStaPum.u1); connect(yFreHeaCoi.y, swiFreStaVal.u1); connect(freSta.y, swiFreStaPum.u2); connect(freSta.y, swiFreStaVal.u2); connect(sysHysHea.y, swiFreStaVal.u3); connect(sysHysHea.yPum, swiFreStaPum.u3); connect(swiFreStaPum.y, pumHeaCoi.y); connect(swiFreStaVal.y, valHeaCoi.y); connect(TRooMin.y, controlBus.TRooMin); connect(TRooMin.u, TRoo); connect(TRooAve.u, TRoo); connect(freSta.u, TMix.T); connect(damExh.port_b, amb.ports[3]); connect(TRoo, conVAV.TRoo); connect(controlBus.TRooSetHea, TRooHeaSet.u); connect(controlBus.TRooSetCoo, TRooCooSet.u); connect(TRooHeaSet.y, conVAV.TRooHeaSet); connect(TRooCooSet.y, conVAV.TRooCooSet); connect(conVAV.yDam, VAVBox.yVAV); connect(conVAV.yVal, VAVBox.yHea); end ASHRAE2006;

model Floor "Model of a floor of the building" extends Buildings.Examples.VAVReheat.BaseClasses.PartialFloor( final VRooCor=cor.AFlo*hRoo, final VRooSou=sou.AFlo*hRoo, final VRooNor=nor.AFlo*hRoo, final VRooEas=eas.AFlo*hRoo, final VRooWes=wes.AFlo*hRoo, AFloCor=2698/hRoo, AFloSou=568.77/hRoo, AFloNor=568.77/hRoo, AFloEas=360.0785/hRoo, AFloWes=360.0785/hRoo); parameter Modelica.Units.SI.Length wExtSou=49.91 "South zone exterior wall width"; parameter Modelica.Units.SI.Length wExtNor=49.91 "North zone exterior wall width"; parameter Modelica.Units.SI.Length wExtEas=33.27 "East zone exterior wall width"; parameter Modelica.Units.SI.Length wExtWes=33.27 "West zone exterior wall width"; parameter HeatTransfer.Types.InteriorConvection intConMod=Buildings.HeatTransfer.Types.InteriorConvection.Temperature "Convective heat transfer model for room-facing surfaces of opaque constructions"; parameter Real winWalRat( min=0.01, max=0.99) = 0.33 "Window to wall ratio for exterior walls"; parameter Modelica.Units.SI.Length hWin=1.5 "Height of windows"; parameter HeatTransfer.Data.Solids.Plywood matFur(x=0.15, nStaRef=5) "Material for furniture"; parameter HeatTransfer.Data.Resistances.Carpet matCar "Carpet"; parameter HeatTransfer.Data.Solids.Concrete matCon( x=0.1, k=1.311, c=836, nStaRef=5) "Concrete"; parameter HeatTransfer.Data.Solids.Plywood matWoo( x=0.01, k=0.11, d=544, nStaRef=1) "Wood for exterior construction"; parameter HeatTransfer.Data.Solids.Generic matIns( x=0.087, k=0.049, c=836.8, d=265, nStaRef=5) "Steelframe construction with insulation"; parameter HeatTransfer.Data.Solids.GypsumBoard matGyp( x=0.0127, k=0.16, c=830, d=784, nStaRef=2) "Gypsum board"; parameter HeatTransfer.Data.Solids.GypsumBoard matGyp2( x=0.025, k=0.16, c=830, d=784, nStaRef=2) "Gypsum board"; parameter HeatTransfer.Data.OpaqueConstructions.Generic conExtWal(final nLay=3, material={matWoo,matIns,matGyp}) "Exterior construction"; parameter HeatTransfer.Data.OpaqueConstructions.Generic conIntWal(final nLay=1, material={matGyp2}) "Interior wall construction"; parameter HeatTransfer.Data.OpaqueConstructions.Generic conFlo(final nLay=1, material={ matCon}) "Floor construction (opa_a is carpet)"; parameter HeatTransfer.Data.OpaqueConstructions.Generic conFur(final nLay=1, material={ matFur}) "Construction for internal mass of furniture"; parameter HeatTransfer.Data.Solids.Plywood matCarTra( k=0.11, d=544, nStaRef=1, x=0.215/0.11) "Wood for floor"; parameter HeatTransfer.Data.GlazingSystems.DoubleClearAir13Clear glaSys( UFra=2, shade=Buildings.HeatTransfer.Data.Shades.Gray(), haveInteriorShade=false, haveExteriorShade=false) "Data record for the glazing system"; constant Modelica.Units.SI.Height hRoo=2.74 "Room height"; parameter Boolean sampleModel = false "Set to true to time-sample the model, which can give shorter simulation time if there is already time sampling in the system model"; Buildings.ThermalZones.Detailed.MixedAir sou( redeclare package Medium = Medium, AFlo=AFloSou, hRoo=hRoo, nConExt=0, nConExtWin=1, datConExtWin( layers={conExtWal}, A={wExtSou*hRoo}, glaSys={glaSys}, wWin={winWalRat/hWin*wExtSou*hRoo}, each hWin=hWin, fFra={0.1}, til={Buildings.Types.Tilt.Wall}, azi={Buildings.Types.Azimuth.S}), nConPar=2, datConPar( layers={conFlo,conFur}, A={AFloSou,414.68}, til={Buildings.Types.Tilt.Floor,Buildings.Types.Tilt.Wall}), nConBou=3, datConBou( layers={conIntWal,conIntWal,conIntWal}, A={6.47,40.76,6.47}*hRoo, til={Buildings.Types.Tilt.Wall, Buildings.Types.Tilt.Wall, Buildings.Types.Tilt.Wall}), nSurBou=0, nPorts=5, intConMod=intConMod, energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial, final sampleModel=sampleModel) "South zone"; Buildings.ThermalZones.Detailed.MixedAir eas( redeclare package Medium = Medium, AFlo=AFloEas, hRoo=hRoo, nConExt=0, nConExtWin=1, datConExtWin( layers={conExtWal}, A={wExtEas*hRoo}, glaSys={glaSys}, wWin={winWalRat/hWin*wExtEas*hRoo}, each hWin=hWin, fFra={0.1}, til={Buildings.Types.Tilt.Wall}, azi={Buildings.Types.Azimuth.E}), nConPar=2, datConPar( layers={conFlo,conFur}, A={AFloEas,262.52}, til={Buildings.Types.Tilt.Floor,Buildings.Types.Tilt.Wall}), nConBou=1, datConBou( layers={conIntWal}, A={24.13}*hRoo, til={Buildings.Types.Tilt.Wall}), nSurBou=2, surBou( each A=6.47*hRoo, each absIR=0.9, each absSol=0.9, til={Buildings.Types.Tilt.Wall, Buildings.Types.Tilt.Wall}), nPorts=5, intConMod=intConMod, energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial, final sampleModel=sampleModel) "East zone"; Buildings.ThermalZones.Detailed.MixedAir nor( redeclare package Medium = Medium, AFlo=AFloNor, hRoo=hRoo, nConExt=0, nConExtWin=1, datConExtWin( layers={conExtWal}, A={wExtNor*hRoo}, glaSys={glaSys}, wWin={winWalRat/hWin*wExtNor*hRoo}, each hWin=hWin, fFra={0.1}, til={Buildings.Types.Tilt.Wall}, azi={Buildings.Types.Azimuth.N}), nConPar=2, datConPar( layers={conFlo,conFur}, A={AFloNor,414.68}, til={Buildings.Types.Tilt.Floor,Buildings.Types.Tilt.Wall}), nConBou=3, datConBou( layers={conIntWal,conIntWal,conIntWal}, A={6.47,40.76,6.47}*hRoo, til={Buildings.Types.Tilt.Wall, Buildings.Types.Tilt.Wall, Buildings.Types.Tilt.Wall}), nSurBou=0, nPorts=5, intConMod=intConMod, energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial, final sampleModel=sampleModel) "North zone"; Buildings.ThermalZones.Detailed.MixedAir wes( redeclare package Medium = Medium, AFlo=AFloWes, hRoo=hRoo, nConExt=0, nConExtWin=1, datConExtWin( layers={conExtWal}, A={wExtEas*hRoo}, glaSys={glaSys}, wWin={winWalRat/hWin*wExtEas*hRoo}, each hWin=hWin, fFra={0.1}, til={Buildings.Types.Tilt.Wall}, azi={Buildings.Types.Azimuth.W}), nConPar=2, datConPar( layers={conFlo,conFur}, A={AFloWes,262.52}, til={Buildings.Types.Tilt.Floor,Buildings.Types.Tilt.Wall}), nConBou=1, datConBou( layers={conIntWal}, A={24.13}*hRoo, til={Buildings.Types.Tilt.Wall}), nSurBou=2, surBou( each A=6.47*hRoo, each absIR=0.9, each absSol=0.9, til={Buildings.Types.Tilt.Wall, Buildings.Types.Tilt.Wall}), nPorts=5, intConMod=intConMod, energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial, final sampleModel=sampleModel) "West zone"; Buildings.ThermalZones.Detailed.MixedAir cor( redeclare package Medium = Medium, AFlo=AFloCor, hRoo=hRoo, nConExt=0, nConExtWin=0, nConPar=2, datConPar( layers={conFlo,conFur}, A={AFloCor,1967.01}, til={Buildings.Types.Tilt.Floor,Buildings.Types.Tilt.Wall}), nConBou=0, nSurBou=4, surBou( A={40.76,24.13,40.76,24.13}*hRoo, each absIR=0.9, each absSol=0.9, til={Buildings.Types.Tilt.Wall, Buildings.Types.Tilt.Wall, Buildings.Types.Tilt.Wall, Buildings.Types.Tilt.Wall}), nPorts=11, intConMod=intConMod, energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial, final sampleModel=sampleModel) "Core zone"; Modelica.Blocks.Math.MatrixGain gai(K=20*[0.4; 0.4; 0.2]) "Matrix gain to split up heat gain in radiant, convective and latent gain"; Modelica.Blocks.Sources.CombiTimeTable intGaiFra( table=[0,0.05; 8,0.05; 9,0.9; 12,0.9; 12,0.8; 13,0.8; 13,1; 17,1; 19,0.1; 24,0.05], timeScale=3600, extrapolation=Modelica.Blocks.Types.Extrapolation.Periodic) "Fraction of internal heat gain"; Modelica.Blocks.Math.Gain gaiIntNor[3](each k=kIntNor) "Gain for internal heat gain amplification for north zone"; Modelica.Blocks.Math.Gain gaiIntSou[3](each k=2 - kIntNor) "Gain to change the internal heat gain for south"; Modelica.Blocks.Sources.Constant uSha(k=0) "Control signal for the shading device"; Modelica.Blocks.Routing.Replicator replicator(nout=1); equation connect(sou.surf_conBou[1], wes.surf_surBou[2]); connect(sou.surf_conBou[2], cor.surf_surBou[1]); connect(sou.surf_conBou[3], eas.surf_surBou[1]); connect(eas.surf_conBou[1], cor.surf_surBou[2]); connect(eas.surf_surBou[2], nor.surf_conBou[1]); connect(nor.surf_conBou[2], cor.surf_surBou[3]); connect(nor.surf_conBou[3], wes.surf_surBou[1]); connect(wes.surf_conBou[1], cor.surf_surBou[4]); connect(replicator.y, nor.uSha); connect(replicator.y, wes.uSha); connect(replicator.y, eas.uSha); connect(replicator.y, sou.uSha); connect(replicator.y, cor.uSha); connect(gai.y, cor.qGai_flow); connect(gai.y, eas.qGai_flow); connect(gai.y, wes.qGai_flow); connect(sou.weaBus, weaBus); connect(eas.weaBus, weaBus); connect(nor.weaBus, weaBus); connect(wes.weaBus, weaBus); connect(cor.weaBus, weaBus); connect(sou.heaPorAir, temAirSou.port); connect(eas.heaPorAir, temAirEas.port); connect(nor.heaPorAir, temAirNor.port); connect(wes.heaPorAir, temAirWes.port); connect(cor.heaPorAir, temAirCor.port); connect(sou.ports[1], portsSou[1]); connect(sou.ports[2], portsSou[2]); connect(eas.ports[1], portsEas[1]); connect(eas.ports[2], portsEas[2]); connect(nor.ports[1], portsNor[1]); connect(nor.ports[2], portsNor[2]); connect(wes.ports[1], portsWes[1]); connect(wes.ports[2], portsWes[2]); connect(cor.ports[1], portsCor[1]); connect(cor.ports[2], portsCor[2]); connect(leaSou.port_b, sou.ports[3]); connect(leaEas.port_b, eas.ports[3]); connect(leaNor.port_b, nor.ports[3]); connect(leaWes.port_b, wes.ports[3]); connect(opeSouCor.port_b1, cor.ports[3]); connect(opeSouCor.port_a2, cor.ports[4]); connect(opeSouCor.port_a1, sou.ports[4]); connect(opeSouCor.port_b2, sou.ports[5]); connect(opeEasCor.port_b1, eas.ports[4]); connect(opeEasCor.port_a2, eas.ports[5]); connect(opeEasCor.port_a1, cor.ports[5]); connect(opeEasCor.port_b2, cor.ports[6]); connect(opeNorCor.port_b1, nor.ports[4]); connect(opeNorCor.port_a2, nor.ports[5]); connect(opeNorCor.port_a1, cor.ports[7]); connect(opeNorCor.port_b2, cor.ports[8]); connect(opeWesCor.port_b1, cor.ports[9]); connect(opeWesCor.port_a2, cor.ports[10]); connect(opeWesCor.port_a1, wes.ports[4]); connect(opeWesCor.port_b2, wes.ports[5]); connect(cor.ports[11], senRelPre.port_a); connect(senRelPre.p_rel, p_rel); connect(gaiIntNor.y, nor.qGai_flow); connect(gaiIntSou.y, sou.qGai_flow); connect(gai.y,gaiIntSou. u); connect(gai.y,gaiIntNor. u); connect(intGaiFra.y,gai. u); connect(uSha.y,replicator. u); end Floor;

model Guideline36 "Variable air volume flow system with terminal reheat and Guideline 36 control sequence serving five thermal zones" extends Buildings.Examples.VAVReheat.BaseClasses.PartialHVAC( damOut( dpDamper_nominal=10, dpFixed_nominal=10), amb(nPorts=3)); parameter Modelica.Units.SI.VolumeFlowRate minZonPriFlo[numZon]=conVAV.VDisSetMin_flow "Minimum expected zone primary flow rate"; parameter Modelica.Units.SI.Time samplePeriod=120 "Sample period of component, set to the same value as the trim and respond that process yPreSetReq"; parameter Modelica.Units.SI.PressureDifference dpDisRetMax(displayUnit="Pa")= 40 "Maximum return fan discharge static pressure setpoint"; Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.Controller conVAV[numZon]( V_flow_nominal=mCooVAV_flow_nominal/1.2, AFlo=AFlo, each final samplePeriod=samplePeriod, VDisSetMin_flow={max(1.5*VZonOA_flow_nominal[i], 0.15*mCooVAV_flow_nominal[ i]/1.2) for i in 1:numZon}, VDisHeaSetMax_flow=mHeaVAV_flow_nominal/1.2) "Controller for terminal unit"; Buildings.Controls.OBC.CDL.Integers.MultiSum TZonResReq(nin=numZon) "Number of zone temperature requests"; Buildings.Controls.OBC.CDL.Integers.MultiSum PZonResReq(nin=numZon) "Number of zone pressure requests"; Buildings.Controls.OBC.CDL.Continuous.Switch swiFreStaPum "Switch for freeze stat of pump"; Buildings.Controls.OBC.CDL.Continuous.Sources.Constant yFreHeaCoi(final k=1) "Flow rate signal for heating coil when freeze stat is on"; Buildings.Controls.OBC.ASHRAE.G36_PR1.AHUs.MultiZone.VAV.Controller conAHU( kMinOut=0.03, final pMaxSet=410, final yFanMin=yFanMin, final VPriSysMax_flow=mAir_flow_nominal/1.2, final peaSysPop=divP*sum({ratP_A*AFlo[i] for i in 1:numZon})) "AHU controller"; Buildings.Controls.OBC.ASHRAE.G36_PR1.AHUs.MultiZone.VAV.SetPoints.OutdoorAirFlow.Zone zonOutAirSet[numZon]( final AFlo=AFlo, final have_occSen=fill(false, numZon), final have_winSen=fill(false, numZon), final desZonPop={ratP_A*AFlo[i] for i in 1:numZon}, final minZonPriFlo=minZonPriFlo) "Zone level calculation of the minimum outdoor airflow setpoint"; Buildings.Controls.OBC.ASHRAE.G36_PR1.AHUs.MultiZone.VAV.SetPoints.OutdoorAirFlow.SumZone zonToSys(final numZon=numZon) "Sum up zone calculation output"; Buildings.Controls.OBC.CDL.Routing.RealScalarReplicator reaRep1(final nout=numZon) "Replicate design uncorrected minimum outdoor airflow setpoint"; Buildings.Controls.OBC.CDL.Routing.BooleanScalarReplicator booRep1(final nout=numZon) "Replicate signal whether the outdoor airflow is required"; Buildings.Controls.OBC.ASHRAE.G36_PR1.Generic.SetPoints.ZoneStatus zonSta[numZon] "Check zone temperature status"; Buildings.Controls.OBC.ASHRAE.G36_PR1.Generic.SetPoints.GroupStatus zonGroSta( final numZon=numZon) "Check zone group status according to the zones status"; Buildings.Controls.OBC.ASHRAE.G36_PR1.Generic.SetPoints.OperationMode opeModSel(final numZon=numZon); Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.SetPoints.ZoneTemperatures TZonSet[numZon]( final have_occSen=fill(false, numZon), final have_winSen=fill(false, numZon)) "Zone setpoint"; Buildings.Controls.OBC.CDL.Continuous.Sources.Constant warCooTim[numZon]( final k=fill(1800, numZon)) "Warm up and cool down time"; Buildings.Controls.OBC.CDL.Logical.Sources.Constant falSta[numZon]( final k=fill(false, numZon)) "All windows are closed, no zone has override switch"; Buildings.Controls.OBC.CDL.Routing.RealScalarReplicator reaRep(nout=numZon) "Assume all zones have same occupancy schedule"; Buildings.Controls.OBC.CDL.Routing.BooleanScalarReplicator booRep(nout=numZon) "Assume all zones have same occupancy schedule"; Buildings.Controls.OBC.CDL.Integers.Sources.Constant demLimLev[numZon]( final k=fill(0, numZon)) "Demand limit level, assumes to be 0"; Buildings.Controls.OBC.CDL.Routing.IntegerScalarReplicator intRep( final nout=numZon) "All zones in same operation mode"; Controls.SystemHysteresis sysHysHea "Hysteresis and delay to switch heating on and off"; Controls.SystemHysteresis sysHysCoo "Hysteresis and delay to switch cooling on and off"; Buildings.Controls.OBC.CDL.Continuous.Switch swiFreStaVal "Switch for freeze stat of valve"; Controls.FreezeStat freSta(lockoutTime=3600) "Freeze stat for heating coil"; Buildings.Controls.OBC.CDL.Routing.RealScalarReplicator TSupAHU(final nout= numZon) "Replicate AHU supply temperature"; Buildings.Controls.OBC.CDL.Routing.IntegerScalarReplicator opeMod(final nout= numZon) "Replicate operation mode"; Buildings.Controls.OBC.Utilities.OptimalStart optSta[numZon]( each computeHeating=true, each computeCooling=true) "Optimal startup"; Buildings.Controls.OBC.CDL.Routing.RealScalarReplicator tZonNexOcc(nout= numZon) "Next occupancy for each zone"; Buildings.Controls.OBC.CDL.Continuous.Sources.Constant TZonSetHea[numZon]( each k( unit="K", displayUnit="degC") = 293.15) "Heating setpoint for zone air"; Buildings.Controls.OBC.CDL.Continuous.Sources.Constant TZonSetCoo[numZon]( each k( unit="K", displayUnit="degC") = 297.15) "Cooling setpoint for zone air"; equation connect(conVAV.TDis, VAVBox.TSup); connect(conVAV.yZonTemResReq, TZonResReq.u); connect(conVAV.yZonPreResReq, PZonResReq.u); connect(conVAV.VDis_flow, VAVBox.VSup_flow); connect(yFreHeaCoi.y, swiFreStaPum.u1); connect(zonToSys.ySumDesZonPop, conAHU.sumDesZonPop); connect(zonToSys.VSumDesPopBreZon_flow, conAHU.VSumDesPopBreZon_flow); connect(zonToSys.VSumDesAreBreZon_flow, conAHU.VSumDesAreBreZon_flow); connect(zonToSys.yDesSysVenEff, conAHU.uDesSysVenEff); connect(zonToSys.VSumUncOutAir_flow, conAHU.VSumUncOutAir_flow); connect(zonToSys.VSumSysPriAir_flow, conAHU.VSumSysPriAir_flow); connect(zonToSys.uOutAirFra_max, conAHU.uOutAirFra_max); connect(zonOutAirSet.yDesZonPeaOcc, zonToSys.uDesZonPeaOcc); connect(zonOutAirSet.VDesPopBreZon_flow, zonToSys.VDesPopBreZon_flow); connect(zonOutAirSet.VDesAreBreZon_flow, zonToSys.VDesAreBreZon_flow); connect(zonOutAirSet.yDesPriOutAirFra, zonToSys.uDesPriOutAirFra); connect(zonOutAirSet.VUncOutAir_flow, zonToSys.VUncOutAir_flow); connect(zonOutAirSet.yPriOutAirFra, zonToSys.uPriOutAirFra); connect(zonOutAirSet.VPriAir_flow, zonToSys.VPriAir_flow); connect(conAHU.yAveOutAirFraPlu, zonToSys.yAveOutAirFraPlu); connect(conAHU.VDesUncOutAir_flow, reaRep1.u); connect(reaRep1.y, zonOutAirSet.VUncOut_flow_nominal); connect(conAHU.yReqOutAir, booRep1.u); connect(booRep1.y, zonOutAirSet.uReqOutAir); connect(TZonResReq.y, conAHU.uZonTemResReq); connect(PZonResReq.y, conAHU.uZonPreResReq); connect(TOut.y, conAHU.TOut); connect(dpDisSupFan.p_rel, conAHU.ducStaPre); connect(TSup.T, conAHU.TSup); connect(TRet.T, conAHU.TOutCut); connect(VOut1.V_flow, conAHU.VOut_flow); connect(TMix.T, conAHU.TMix); connect(conAHU.yOutDamPos, damOut.y); connect(conAHU.yRetDamPos, damRet.y); connect(conAHU.ySupFanSpe, fanSup.y); connect(VAVBox.y_actual, conVAV.yDam_actual); connect(zonSta.yCooTim, zonGroSta.uCooTim); connect(zonSta.yWarTim, zonGroSta.uWarTim); connect(zonSta.yOccHeaHig, zonGroSta.uOccHeaHig); connect(zonSta.yHigOccCoo, zonGroSta.uHigOccCoo); connect(zonSta.THeaSetOff, zonGroSta.THeaSetOff); connect(zonSta.yUnoHeaHig, zonGroSta.uUnoHeaHig); connect(zonSta.yEndSetBac, zonGroSta.uEndSetBac); connect(zonSta.TCooSetOff, zonGroSta.TCooSetOff); connect(zonSta.yHigUnoCoo, zonGroSta.uHigUnoCoo); connect(zonSta.yEndSetUp, zonGroSta.uEndSetUp); connect(falSta.y, zonGroSta.uWin); connect(occSch.tNexOcc, reaRep.u); connect(reaRep.y, zonGroSta.tNexOcc); connect(occSch.occupied, booRep.u); connect(booRep.y, zonGroSta.uOcc); connect(falSta.y, zonGroSta.zonOcc); connect(zonGroSta.uGroOcc, opeModSel.uOcc); connect(zonGroSta.nexOcc, opeModSel.tNexOcc); connect(zonGroSta.yCooTim, opeModSel.maxCooDowTim); connect(zonGroSta.yWarTim, opeModSel.maxWarUpTim); connect(zonGroSta.yOccHeaHig, opeModSel.uOccHeaHig); connect(zonGroSta.yHigOccCoo, opeModSel.uHigOccCoo); connect(zonGroSta.yColZon, opeModSel.totColZon); connect(zonGroSta.ySetBac, opeModSel.uSetBac); connect(zonGroSta.yEndSetBac, opeModSel.uEndSetBac); connect(zonGroSta.TZonMin, opeModSel.TZonMin); connect(zonGroSta.yHotZon, opeModSel.totHotZon); connect(zonGroSta.ySetUp, opeModSel.uSetUp); connect(zonGroSta.yEndSetUp, opeModSel.uEndSetUp); connect(zonSta.THeaSetOn, TZonSet.TZonHeaSetOcc); connect(zonSta.THeaSetOff, TZonSet.TZonHeaSetUno); connect(zonSta.TCooSetOn, TZonSet.TZonCooSetOcc); connect(zonSta.TCooSetOff, TZonSet.TZonCooSetUno); connect(demLimLev.y, TZonSet.uCooDemLimLev); connect(demLimLev.y, TZonSet.uHeaDemLimLev); connect(opeModSel.yOpeMod, conAHU.uOpeMod); connect(TZonSet[1].TZonHeaSet, conAHU.TZonHeaSet); connect(TZonSet[1].TZonCooSet, conAHU.TZonCooSet); connect(TZonSet.TZonHeaSet, conVAV.TZonHeaSet); connect(TZonSet.TZonCooSet, conVAV.TZonCooSet); connect(opeModSel.yOpeMod, intRep.u); connect(intRep.y, TZonSet.uOpeMod); connect(zonGroSta.yOpeWin, opeModSel.uOpeWin); connect(VAVBox.yVAV, conVAV.yDam); connect(VAVBox.yHea, conVAV.yVal); connect(freSta.y, swiFreStaPum.u2); connect(sysHysCoo.y, valCooCoi.y); connect(sysHysCoo.yPum, pumCooCoi.y); connect(conAHU.yCoo, sysHysCoo.u); connect(conAHU.yHea, sysHysHea.u); connect(sysHysHea.sysOn, conAHU.ySupFan); connect(swiFreStaPum.y, pumHeaCoi.y); connect(swiFreStaVal.u1, yFreHeaCoi.y); connect(sysHysHea.y, swiFreStaVal.u3); connect(sysHysHea.yPum, swiFreStaPum.u3); connect(freSta.y, swiFreStaVal.u2); connect(swiFreStaVal.y, valHeaCoi.y); connect(sysHysCoo.sysOn, conAHU.ySupFan); connect(zonGroSta.TZon, TRoo); connect(zonSta.TZon, TRoo); connect(zonOutAirSet.TZon, TRoo); connect(TMix.T, freSta.u); connect(TRet.port_b, amb.ports[3]); connect(TRoo, conVAV.TZon); connect(zonOutAirSet.VDis_flow, VAVBox.VSup_flow); connect(VAVBox.TSup, zonOutAirSet.TDis); connect(TSup.T, TSupAHU.u); connect(TSupAHU.y, conVAV.TSupAHU); connect(opeModSel.yOpeMod, opeMod.u); connect(opeMod.y, conVAV.uOpeMod); connect(optSta.TZon, TRoo); connect(optSta.tOpt, zonSta.cooDowTim); connect(optSta.tOpt, zonSta.warUpTim); connect(occSch.tNexOcc, tZonNexOcc.u); connect(tZonNexOcc.y, optSta.tNexOcc); connect(optSta.TSetZonCoo, TZonSetCoo.y); connect(optSta.TSetZonHea, TZonSetHea.y); end Guideline36;

partial model HVACBuilding "Partial model that contains the HVAC and building model" replaceable package MediumA = Buildings.Media.Air "Medium model for air"; replaceable package MediumW = Buildings.Media.Water "Medium model for water"; final parameter Modelica.Units.SI.Volume VRooCor=flo.VRooCor "Room volume corridor"; final parameter Modelica.Units.SI.Volume VRooSou=flo.VRooSou "Room volume south"; final parameter Modelica.Units.SI.Volume VRooNor=flo.VRooNor "Room volume north"; final parameter Modelica.Units.SI.Volume VRooEas=flo.VRooEas "Room volume east"; final parameter Modelica.Units.SI.Volume VRooWes=flo.VRooWes "Room volume west"; final parameter Modelica.Units.SI.Area AFloCor=flo.AFloCor "Floor area corridor"; final parameter Modelica.Units.SI.Area AFloSou=flo.AFloSou "Floor area south"; final parameter Modelica.Units.SI.Area AFloNor=flo.AFloNor "Floor area north"; final parameter Modelica.Units.SI.Area AFloEas=flo.AFloEas "Floor area east"; final parameter Modelica.Units.SI.Area AFloWes=flo.AFloWes "Floor area west"; constant Real conv=1.2/3600 "Conversion factor for nominal mass flow rate"; parameter Modelica.Units.SI.MassFlowRate mCor_flow_nominal "Design mass flow rate core"; parameter Modelica.Units.SI.MassFlowRate mSou_flow_nominal "Design mass flow rate south"; parameter Modelica.Units.SI.MassFlowRate mEas_flow_nominal "Design mass flow rate east"; parameter Modelica.Units.SI.MassFlowRate mNor_flow_nominal "Design mass flow rate north"; parameter Modelica.Units.SI.MassFlowRate mWes_flow_nominal "Design mass flow rate west"; final parameter Modelica.Units.SI.MassFlowRate mCooVAV_flow_nominal[5]={ mSou_flow_nominal,mEas_flow_nominal,mNor_flow_nominal,mWes_flow_nominal, mCor_flow_nominal} "Design mass flow rate of each zone"; parameter Modelica.Units.SI.Temperature THeaWatInl_nominal(displayUnit="degC")= 45 + 273.15 "Reheat coil nominal inlet water temperature"; replaceable Buildings.Examples.VAVReheat.BaseClasses.PartialHVAC hvac constrainedby Buildings.Examples.VAVReheat.BaseClasses.PartialHVAC( redeclare final package MediumA = MediumA, redeclare final package MediumW = MediumW, final VRoo={VRooSou,VRooEas,VRooNor,VRooWes,VRooCor}, final AFlo={AFloSou,AFloEas,AFloNor,AFloWes,AFloCor}, final mCooVAV_flow_nominal=mCooVAV_flow_nominal, final THeaWatInl_nominal=THeaWatInl_nominal) "HVAC system"; replaceable Buildings.Examples.VAVReheat.BaseClasses.PartialFloor flo constrainedby Buildings.Examples.VAVReheat.BaseClasses.PartialFloor( redeclare final package Medium = MediumA) "Building"; Buildings.BoundaryConditions.WeatherData.ReaderTMY3 weaDat( filNam=Modelica.Utilities.Files.loadResource( "modelica://Buildings/Resources/weatherdata/USA_IL_Chicago-OHare.Intl.AP.725300_TMY3.mos"), computeWetBulbTemperature=false) "Weather data reader"; Fluid.Sources.Boundary_pT sinHea( redeclare package Medium = MediumW, p=300000, T=THeaWatInl_nominal, nPorts=1) "Sink for heating coil"; Fluid.Sources.Boundary_pT souHea( redeclare package Medium = MediumW, p(displayUnit="Pa") = 300000 + 6000, T=THeaWatInl_nominal, nPorts=1) "Source for heating coil"; Fluid.Sources.Boundary_pT sinCoo( redeclare package Medium = MediumW, p=300000, T=279.15, nPorts=1) "Sink for cooling coil"; Fluid.Sources.Boundary_pT souCoo( redeclare package Medium = MediumW, p(displayUnit="Pa") = 300000 + 6000, T=279.15, nPorts=1) "Source for cooling coil loop"; Fluid.Sources.Boundary_pT souHeaTer( redeclare package Medium = MediumW, p(displayUnit="Pa") = 300000 + 6000, T=THeaWatInl_nominal, nPorts=1) "Source for heating of terminal boxes"; Fluid.Sources.Boundary_pT sinHeaTer( redeclare package Medium = MediumW, p(displayUnit="Pa") = 300000, T=THeaWatInl_nominal, nPorts=1) "Source for heating of terminal boxes"; equation connect(souHea.ports[1], hvac.portHeaCoiSup); connect(sinHea.ports[1], hvac.portHeaCoiRet); connect(hvac.portHeaTerSup, souHeaTer.ports[1]); connect(hvac.portHeaTerRet, sinHeaTer.ports[1]); connect(weaDat.weaBus, hvac.weaBus); connect(flo.TRooAir, hvac.TRoo); connect(hvac.port_supAir[1], flo.portsSou[1]); connect(hvac.port_supAir[2], flo.portsEas[1]); connect(hvac.port_supAir[3], flo.portsNor[1]); connect(hvac.port_supAir[4], flo.portsWes[1]); connect(hvac.port_supAir[5], flo.portsCor[1]); connect(hvac.port_retAir[1], flo.portsSou[2]); connect(hvac.port_retAir[2], flo.portsEas[2]); connect(hvac.port_retAir[3], flo.portsNor[2]); connect(hvac.port_retAir[4], flo.portsWes[2]); connect(hvac.port_retAir[5], flo.portsCor[2]); connect(weaDat.weaBus, flo.weaBus); connect(souCoo.ports[1], hvac.portCooCoiSup); connect(sinCoo.ports[1], hvac.portCooCoiRet); end HVACBuilding;

partial model PartialFloor "Interface for a model of a floor of a building" replaceable package Medium = Modelica.Media.Interfaces.PartialMedium "Medium model for air"; parameter Boolean use_windPressure=true "Set to true to enable wind pressure"; parameter Real kIntNor(min=0, max=1) = 1 "Gain factor to scale internal heat gain in north zone"; parameter Modelica.Units.SI.Volume VRooCor "Room volume corridor"; parameter Modelica.Units.SI.Volume VRooSou "Room volume south"; parameter Modelica.Units.SI.Volume VRooNor "Room volume north"; parameter Modelica.Units.SI.Volume VRooEas "Room volume east"; parameter Modelica.Units.SI.Volume VRooWes "Room volume west"; parameter Modelica.Units.SI.Area AFloCor "Floor area corridor"; parameter Modelica.Units.SI.Area AFloSou "Floor area south"; parameter Modelica.Units.SI.Area AFloNor "Floor area north"; parameter Modelica.Units.SI.Area AFloEas "Floor area east"; parameter Modelica.Units.SI.Area AFloWes "Floor area west"; Modelica.Fluid.Vessels.BaseClasses.VesselFluidPorts_b portsSou[2]( redeclare package Medium = Medium) "Fluid inlets and outlets"; Modelica.Fluid.Vessels.BaseClasses.VesselFluidPorts_b portsEas[2]( redeclare package Medium = Medium) "Fluid inlets and outlets"; Modelica.Fluid.Vessels.BaseClasses.VesselFluidPorts_b portsNor[2]( redeclare package Medium = Medium) "Fluid inlets and outlets"; Modelica.Fluid.Vessels.BaseClasses.VesselFluidPorts_b portsWes[2]( redeclare package Medium = Medium) "Fluid inlets and outlets"; Modelica.Fluid.Vessels.BaseClasses.VesselFluidPorts_b portsCor[2]( redeclare package Medium = Medium) "Fluid inlets and outlets"; Modelica.Blocks.Interfaces.RealOutput TRooAir[5]( each unit="K", each displayUnit="degC") "Room air temperatures"; Modelica.Blocks.Interfaces.RealOutput p_rel "Relative pressure signal of building static pressure"; BoundaryConditions.WeatherData.Bus weaBus "Weather bus"; Buildings.Examples.VAVReheat.BaseClasses.RoomLeakage leaSou( redeclare package Medium = Medium, VRoo=VRooSou, s=49.91/33.27, azi=Buildings.Types.Azimuth.S, final use_windPressure=use_windPressure) "Model for air infiltration through the envelope"; Buildings.Examples.VAVReheat.BaseClasses.RoomLeakage leaEas( redeclare package Medium = Medium, VRoo=VRooEas, s=33.27/49.91, azi=Buildings.Types.Azimuth.E, final use_windPressure=use_windPressure) "Model for air infiltration through the envelope"; Buildings.Examples.VAVReheat.BaseClasses.RoomLeakage leaNor( redeclare package Medium = Medium, VRoo=VRooNor, s=49.91/33.27, azi=Buildings.Types.Azimuth.N, final use_windPressure=use_windPressure) "Model for air infiltration through the envelope"; Buildings.Examples.VAVReheat.BaseClasses.RoomLeakage leaWes( redeclare package Medium = Medium, VRoo=VRooWes, s=33.27/49.91, azi=Buildings.Types.Azimuth.W, final use_windPressure=use_windPressure) "Model for air infiltration through the envelope"; Modelica.Thermal.HeatTransfer.Sensors.TemperatureSensor temAirSou "Air temperature sensor"; Modelica.Thermal.HeatTransfer.Sensors.TemperatureSensor temAirEas "Air temperature sensor"; Modelica.Thermal.HeatTransfer.Sensors.TemperatureSensor temAirNor "Air temperature sensor"; Modelica.Thermal.HeatTransfer.Sensors.TemperatureSensor temAirWes "Air temperature sensor"; Modelica.Thermal.HeatTransfer.Sensors.TemperatureSensor temAirCor "Air temperature sensor"; Modelica.Blocks.Routing.Multiplex5 multiplex5_1; Airflow.Multizone.DoorOpen opeSouCor( redeclare package Medium = Medium, wOpe=10) "Opening between perimeter1 and core"; Airflow.Multizone.DoorOpen opeEasCor( redeclare package Medium = Medium, wOpe=10) "Opening between perimeter2 and core"; Airflow.Multizone.DoorOpen opeNorCor( redeclare package Medium = Medium, wOpe=10) "Opening between perimeter3 and core"; Airflow.Multizone.DoorOpen opeWesCor(redeclare package Medium = Medium, wOpe=10) "Opening between perimeter3 and core"; Buildings.Fluid.Sensors.RelativePressure senRelPre(redeclare package Medium = Medium) "Building pressure measurement"; Buildings.Fluid.Sources.Outside out(nPorts=1, redeclare package Medium = Medium); equation connect(weaBus, leaSou.weaBus); connect(weaBus, leaEas.weaBus); connect(weaBus, leaNor.weaBus); connect(weaBus, leaWes.weaBus); connect(out.weaBus, weaBus); connect(multiplex5_1.y, TRooAir); connect(temAirSou.T, multiplex5_1.u1[1]); connect(temAirEas.T, multiplex5_1.u2[1]); connect(temAirNor.T, multiplex5_1.u3[1]); connect(temAirWes.T, multiplex5_1.u4[1]); connect(temAirCor.T, multiplex5_1.u5[1]); connect(senRelPre.p_rel, p_rel); connect(out.ports[1], senRelPre.port_b); end PartialFloor;

partial model PartialHVAC "Partial model of variable air volume flow system with terminal reheat that serves five thermal zones" replaceable package MediumA = Buildings.Media.Air constrainedby Modelica.Media.Interfaces.PartialCondensingGases "Medium model for air"; replaceable package MediumW = Buildings.Media.Water "Medium model for water"; constant Integer numZon(min=2)=5 "Total number of served VAV boxes"; parameter Modelica.Units.SI.Volume VRoo[numZon] "Room volume per zone"; parameter Modelica.Units.SI.Area AFlo[numZon] "Floor area per zone"; final parameter Modelica.Units.SI.Area ATot=sum(AFlo) "Total floor area for all zone"; constant Real conv=1.2/3600 "Conversion factor for nominal mass flow rate"; parameter Modelica.Units.SI.HeatFlowRate QHeaAHU_flow_nominal(min=0) = mHeaAir_flow_nominal * cpAir * (THeaAirSup_nominal-THeaAirMix_nominal) "Nominal heating heat flow rate of air handler unit coil"; parameter Modelica.Units.SI.HeatFlowRate QCooAHU_flow_nominal(max=0) = 1.3 * mCooAir_flow_nominal * cpAir *(TCooAirSup_nominal-TCooAirMix_nominal) "Nominal total cooling heat flow rate of air handler unit coil (negative number)"; parameter Modelica.Units.SI.MassFlowRate mCooVAV_flow_nominal[numZon] "Design mass flow rate per zone for cooling"; parameter Modelica.Units.SI.MassFlowRate mHeaVAV_flow_nominal[numZon] = 0.3*mCooVAV_flow_nominal "Design mass flow rate per zone for heating"; parameter Modelica.Units.SI.MassFlowRate mAir_flow_nominal=mCooAir_flow_nominal "Nominal mass flow rate for fan"; parameter Modelica.Units.SI.MassFlowRate mCooAir_flow_nominal=0.7*sum(mCooVAV_flow_nominal) "Nominal mass flow rate for fan"; parameter Modelica.Units.SI.MassFlowRate mHeaAir_flow_nominal = 0.7*sum(mHeaVAV_flow_nominal) "Nominal mass flow rate for fan"; parameter Modelica.Units.SI.MassFlowRate mHeaWat_flow_nominal= QHeaAHU_flow_nominal/cpWat/10 "Nominal water mass flow rate for heating coil in AHU"; parameter Modelica.Units.SI.MassFlowRate mCooWat_flow_nominal= QCooAHU_flow_nominal/cpWat/(-6) "Nominal water mass flow rate for cooling coil"; parameter Real ratOAFlo_A(final unit="m3/(s.m2)") = 0.3e-3 "Outdoor airflow rate required per unit area"; parameter Real ratOAFlo_P = 2.5e-3 "Outdoor airflow rate required per person"; parameter Real ratP_A = 5e-2 "Occupant density"; parameter Real effZ(final unit="1") = 0.8 "Zone air distribution effectiveness (limiting value)"; parameter Real divP(final unit="1") = 0.7 "Occupant diversity ratio"; parameter Modelica.Units.SI.VolumeFlowRate VZonOA_flow_nominal[numZon]=( ratOAFlo_P*ratP_A + ratOAFlo_A)*AFlo/effZ "Zone outdoor air flow rate of each VAV box"; parameter Modelica.Units.SI.VolumeFlowRate Vou_flow_nominal=(divP*ratOAFlo_P* ratP_A + ratOAFlo_A)*sum(AFlo) "System uncorrected outdoor air flow rate"; parameter Real effVen(final unit="1") = if divP < 0.6 then 0.88 * divP + 0.22 else 0.75 "System ventilation efficiency"; parameter Modelica.Units.SI.VolumeFlowRate Vot_flow_nominal=Vou_flow_nominal/ effVen "System design outdoor air flow rate"; parameter Modelica.Units.SI.Temperature THeaOn=293.15 "Heating setpoint during on"; parameter Modelica.Units.SI.Temperature THeaOff=285.15 "Heating setpoint during off"; parameter Modelica.Units.SI.Temperature TCooOn=297.15 "Cooling setpoint during on"; parameter Modelica.Units.SI.Temperature TCooOff=303.15 "Cooling setpoint during off"; parameter Modelica.Units.SI.PressureDifference dpBuiStaSet(min=0) = 12 "Building static pressure"; parameter Real yFanMin = 0.1 "Minimum fan speed"; parameter Modelica.Units.SI.Temperature TCooAirMix_nominal(displayUnit="degC")=303.15 "Mixed air temperature during cooling nominal conditions (used to size cooling coil)"; parameter Modelica.Units.SI.Temperature TCooAirSup_nominal(displayUnit="degC")=285.15 "Supply air temperature during cooling nominal conditions (used to size cooling coil)"; parameter Modelica.Units.SI.MassFraction wCooAirMix_nominal = 0.017 "Humidity ratio of mixed air at a nominal conditions used to size cooling coil (in kg/kg dry total)"; parameter Modelica.Units.SI.Temperature TCooWatInl_nominal(displayUnit="degC") = 279.15 "Cooling coil nominal inlet water temperature"; parameter Modelica.Units.SI.Temperature THeaAirMix_nominal(displayUnit="degC")=277.15 "Mixed air temperature during heating nominal conditions (used to size heating coil)"; parameter Modelica.Units.SI.Temperature THeaAirSup_nominal(displayUnit="degC")=285.15 "Supply air temperature during heating nominal conditions (used to size heating coil)"; parameter Modelica.Units.SI.Temperature THeaWatInl_nominal(displayUnit="degC") "Reheat coil nominal inlet water temperature"; parameter Boolean allowFlowReversal=true "= false to simplify equations, assuming, but not enforcing, no flow reversal"; Modelica.Fluid.Interfaces.FluidPort_a port_supAir[numZon](redeclare package Medium = MediumA) "Supply air to thermal zones"; Modelica.Fluid.Interfaces.FluidPort_a port_retAir[numZon](redeclare package Medium = MediumA) "Return air from thermal zones"; Modelica.Blocks.Interfaces.RealInput TRoo[numZon]( each final unit="K", each displayUnit="degC") "Room temperatures"; Buildings.Fluid.Sources.Outside amb( redeclare package Medium = MediumA, nPorts=2) "Ambient conditions"; Buildings.Fluid.HeatExchangers.DryCoilEffectivenessNTU heaCoi( redeclare package Medium1 = MediumW, redeclare package Medium2 = MediumA, Q_flow_nominal=QHeaAHU_flow_nominal, m1_flow_nominal=mHeaWat_flow_nominal, m2_flow_nominal=mHeaAir_flow_nominal, show_T=true, configuration=Buildings.Fluid.Types.HeatExchangerConfiguration.CounterFlow, dp1_nominal=3000, dp2_nominal=0, allowFlowReversal1=false, allowFlowReversal2=allowFlowReversal, T_a1_nominal=THeaWatInl_nominal, T_a2_nominal=THeaAirMix_nominal) "Heating coil"; Fluid.HeatExchangers.WetCoilEffectivenessNTU cooCoi( redeclare package Medium1 = MediumW, redeclare package Medium2 = MediumA, use_Q_flow_nominal=true, Q_flow_nominal=QCooAHU_flow_nominal, m1_flow_nominal=mCooWat_flow_nominal, m2_flow_nominal=mCooAir_flow_nominal, dp2_nominal=0, dp1_nominal=3000, T_a1_nominal=TCooWatInl_nominal, T_a2_nominal=TCooAirMix_nominal, w_a2_nominal=wCooAirMix_nominal, energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial, allowFlowReversal1=false, allowFlowReversal2=allowFlowReversal, show_T=true) "Cooling coil"; Buildings.Fluid.FixedResistances.PressureDrop dpRetDuc( m_flow_nominal=mAir_flow_nominal, redeclare package Medium = MediumA, allowFlowReversal=allowFlowReversal, dp_nominal=40) "Pressure drop for return duct"; Buildings.Fluid.Movers.SpeedControlled_y fanSup( redeclare package Medium = MediumA, per(pressure( V_flow={0,mAir_flow_nominal/1.2*2}, dp=2*{780 + 10 + dpBuiStaSet,0})), energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial) "Supply air fan"; Buildings.Fluid.Sensors.VolumeFlowRate senSupFlo(redeclare package Medium = MediumA, m_flow_nominal=mAir_flow_nominal) "Sensor for supply fan flow rate"; Buildings.Fluid.Sensors.VolumeFlowRate senRetFlo(redeclare package Medium = MediumA, m_flow_nominal=mAir_flow_nominal) "Sensor for return fan flow rate"; Modelica.Blocks.Routing.RealPassThrough TOut(y( final quantity="ThermodynamicTemperature", final unit="K", displayUnit="degC", min=0)); Buildings.Fluid.Sensors.TemperatureTwoPort TSup( redeclare package Medium = MediumA, m_flow_nominal=mAir_flow_nominal, allowFlowReversal=allowFlowReversal); Buildings.Fluid.Sensors.RelativePressure dpDisSupFan(redeclare package Medium = MediumA) "Supply fan static discharge pressure"; Buildings.Controls.SetPoints.OccupancySchedule occSch(occupancy=3600*{6,19}) "Occupancy schedule"; Buildings.Fluid.Sensors.TemperatureTwoPort TRet( redeclare package Medium = MediumA, m_flow_nominal=mAir_flow_nominal, allowFlowReversal=allowFlowReversal) "Return air temperature sensor"; Buildings.Fluid.Sensors.TemperatureTwoPort TMix( redeclare package Medium = MediumA, m_flow_nominal=mAir_flow_nominal, allowFlowReversal=allowFlowReversal) "Mixed air temperature sensor"; Buildings.Fluid.Sensors.VolumeFlowRate VOut1(redeclare package Medium = MediumA, m_flow_nominal=mAir_flow_nominal) "Outside air volume flow rate"; BoundaryConditions.WeatherData.Bus weaBus "Weather data bus"; Results res( final A=ATot, PFan=fanSup.P + 0, PPum=pumHeaCoi.P + pumCooCoi.P, PHea=heaCoi.Q2_flow + sum(VAVBox.terHea.Q2_flow), PCooSen=cooCoi.QSen2_flow, PCooLat=cooCoi.QLat2_flow) "Results of the simulation"; Fluid.Actuators.Dampers.Exponential damRet( redeclare package Medium = MediumA, m_flow_nominal=mAir_flow_nominal, from_dp=false, riseTime=15, dpDamper_nominal=5, dpFixed_nominal=5) "Return air damper"; Fluid.Actuators.Dampers.Exponential damOut( redeclare package Medium = MediumA, m_flow_nominal=mAir_flow_nominal, from_dp=false, riseTime=15, dpDamper_nominal=5, dpFixed_nominal=5) "Outdoor air damper"; Fluid.FixedResistances.Junction splCooSup( redeclare package Medium = MediumW, m_flow_nominal=mCooWat_flow_nominal*{1,1,1}, energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState, dp_nominal(each displayUnit="Pa") = {0,0,0}, portFlowDirection_1=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Entering, portFlowDirection_2=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving, portFlowDirection_3=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving) "Flow splitter"; Fluid.Actuators.Valves.TwoWayEqualPercentage valCooCoi( redeclare package Medium = MediumW, m_flow_nominal=mCooWat_flow_nominal, dpValve_nominal=6000, dpFixed_nominal=0) "Valve for cooling coil"; Fluid.FixedResistances.Junction splCooRet( redeclare package Medium = MediumW, m_flow_nominal=mCooWat_flow_nominal*{1,1,1}, energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState, dp_nominal(each displayUnit="Pa") = {0,0,0}, portFlowDirection_1=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Entering, portFlowDirection_2=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving, portFlowDirection_3=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving) "Flow splitter"; Fluid.Movers.SpeedControlled_y pumCooCoi( redeclare package Medium = MediumW, per(pressure(V_flow={0,mCooWat_flow_nominal/1000*2}, dp=2*{3000,0})), energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial) "Supply air fan"; Fluid.Movers.SpeedControlled_y pumHeaCoi( redeclare package Medium = MediumW, per(pressure(V_flow={0,mHeaWat_flow_nominal/1000*2}, dp=2*{3000,0})), energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial) "Pump for heating coil"; Fluid.Actuators.Valves.TwoWayEqualPercentage valHeaCoi( redeclare package Medium = MediumW, m_flow_nominal=mHeaWat_flow_nominal, dpValve_nominal=6000, dpFixed_nominal=0) "Valve for heating coil"; Fluid.FixedResistances.Junction splHeaRet( redeclare package Medium = MediumW, m_flow_nominal=mHeaWat_flow_nominal*{1,1,1}, energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState, dp_nominal(each displayUnit="Pa") = {0,0,0}, portFlowDirection_1=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Entering, portFlowDirection_2=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving, portFlowDirection_3=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving) "Flow splitter"; Fluid.FixedResistances.Junction splHeaSup( redeclare package Medium = MediumW, m_flow_nominal=mHeaWat_flow_nominal*{1,1,1}, energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState, dp_nominal(each displayUnit="Pa") = {0,0,0}, portFlowDirection_1=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Entering, portFlowDirection_2=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving, portFlowDirection_3=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving) "Flow splitter"; Modelica.Fluid.Interfaces.FluidPort_a portHeaCoiSup(redeclare package Medium = MediumW) "Heating coil loop supply"; Modelica.Fluid.Interfaces.FluidPort_b portHeaCoiRet(redeclare package Medium = MediumW) "Heating coil loop return"; Modelica.Fluid.Interfaces.FluidPort_a portHeaTerSup(redeclare package Medium = MediumW) "Terminal heat loop supply"; Modelica.Fluid.Interfaces.FluidPort_b portHeaTerRet(redeclare package Medium = MediumW) "Terminal heat loop return"; Modelica.Fluid.Interfaces.FluidPort_a portCooCoiSup(redeclare package Medium = MediumW) "Cooling coil loop supply"; Modelica.Fluid.Interfaces.FluidPort_b portCooCoiRet(redeclare package Medium = MediumW) "Coolin coil loop return"; Buildings.Examples.VAVReheat.BaseClasses.VAVReheatBox VAVBox[numZon]( redeclare each package MediumA = MediumA, redeclare each package MediumW = MediumW, mCooAir_flow_nominal=mCooVAV_flow_nominal, mHeaAir_flow_nominal=mHeaVAV_flow_nominal, VRoo=VRoo, each allowFlowReversal=allowFlowReversal, each THeaWatInl_nominal=THeaWatInl_nominal, each THeaWatOut_nominal=THeaWatInl_nominal - 10, each THeaAirInl_nominal=285.15, each THeaAirDis_nominal=301.15) "VAV boxes"; Buildings.Fluid.FixedResistances.Junction splRetRoo[numZon - 1]( redeclare each package Medium = MediumA, each from_dp=false, each linearized=true, m_flow_nominal={{sum(mCooVAV_flow_nominal[i:numZon]),sum( mCooVAV_flow_nominal[(i + 1):numZon]),mCooVAV_flow_nominal[i]} for i in 1:(numZon - 1)}, each energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState, each dp_nominal(each displayUnit="Pa") = {0,0,0}, each portFlowDirection_1=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving, each portFlowDirection_2=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Entering, each portFlowDirection_3=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Entering) "Splitter for room return air"; Buildings.Fluid.FixedResistances.Junction splSupRoo[numZon - 1]( redeclare each package Medium = MediumA, each from_dp=true, each linearized=true, m_flow_nominal={{sum(mCooVAV_flow_nominal[i:numZon]),sum( mCooVAV_flow_nominal[(i + 1):numZon]),mCooVAV_flow_nominal[i]} for i in 1:(numZon - 1)}, each energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState, each dp_nominal(each displayUnit="Pa") = {0,0,0}, each portFlowDirection_1=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Entering, each portFlowDirection_2=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving, each portFlowDirection_3=if allowFlowReversal then Modelica.Fluid.Types.PortFlowDirection.Bidirectional else Modelica.Fluid.Types.PortFlowDirection.Leaving) "Splitter for room supply air"; Fluid.FixedResistances.PressureDrop dpSupDuc( m_flow_nominal=mAir_flow_nominal, redeclare package Medium = MediumA, allowFlowReversal=allowFlowReversal, dp_nominal=200 + 200 + 100 + 40) "Pressure drop for supply duct"; protected constant Modelica.Units.SI.SpecificHeatCapacity cpAir=Buildings.Utilities.Psychrometrics.Constants.cpAir "Air specific heat capacity"; constant Modelica.Units.SI.SpecificHeatCapacity cpWat=Buildings.Utilities.Psychrometrics.Constants.cpWatLiq "Water specific heat capacity"; model Results "Model to store the results of the simulation" parameter Modelica.Units.SI.Area A "Floor area"; input Modelica.Units.SI.Power PFan "Fan energy"; input Modelica.Units.SI.Power PPum "Pump energy"; input Modelica.Units.SI.Power PHea "Heating energy"; input Modelica.Units.SI.Power PCooSen "Sensible cooling energy"; input Modelica.Units.SI.Power PCooLat "Latent cooling energy"; Real EFan( unit="J/m2", start=0, nominal=1E5, fixed=true) "Fan energy"; Real EPum( unit="J/m2", start=0, nominal=1E5, fixed=true) "Pump energy"; Real EHea( unit="J/m2", start=0, nominal=1E5, fixed=true) "Heating energy"; Real ECooSen( unit="J/m2", start=0, nominal=1E5, fixed=true) "Sensible cooling energy"; Real ECooLat( unit="J/m2", start=0, nominal=1E5, fixed=true) "Latent cooling energy"; Real ECoo(unit="J/m2") "Total cooling energy"; equation A*der(EFan) = PFan; A*der(EPum) = PPum; A*der(EHea) = PHea; A*der(ECooSen) = PCooSen; A*der(ECooLat) = PCooLat; ECoo = ECooSen + ECooLat; end Results; equation connect(fanSup.port_b, dpDisSupFan.port_a); connect(TSup.port_a, fanSup.port_b); connect(amb.ports[1], VOut1.port_a); connect(weaBus.TDryBul, TOut.u); connect(amb.weaBus, weaBus); connect(senRetFlo.port_a, dpRetDuc.port_b); connect(TSup.port_b, senSupFlo.port_a); connect(dpDisSupFan.port_b, amb.ports[2]); connect(senRetFlo.port_b, TRet.port_a); connect(TMix.port_b, heaCoi.port_a2); connect(heaCoi.port_b2, cooCoi.port_a2); connect(VOut1.port_b, damOut.port_a); connect(damOut.port_b, TMix.port_a); connect(damRet.port_a, TRet.port_b); connect(damRet.port_b, TMix.port_a); connect(pumHeaCoi.port_b, heaCoi.port_a1); connect(cooCoi.port_b1,pumCooCoi. port_a); connect(splCooSup.port_2, cooCoi.port_a1); connect(splCooRet.port_3,splCooSup. port_3); connect(pumCooCoi.port_b, splCooRet.port_2); connect(splHeaSup.port_2, pumHeaCoi.port_a); connect(heaCoi.port_b1, splHeaRet.port_2); connect(splHeaRet.port_3, splHeaSup.port_3); connect(splHeaSup.port_1, valHeaCoi.port_b); connect(splCooSup.port_1, valCooCoi.port_b); connect(portHeaCoiSup, valHeaCoi.port_a); connect(portHeaCoiRet, splHeaRet.port_1); connect(portCooCoiSup, valCooCoi.port_a); connect(portCooCoiRet, splCooRet.port_1); connect(VAVBox.port_bAir, port_supAir); for i in 1:numZon loop connect(VAVBox[i].port_aHeaWat, portHeaTerSup); connect(VAVBox[i].port_bHeaWat, portHeaTerRet); end for; connect(splSupRoo[1].port_1, senSupFlo.port_b); connect(splRetRoo[1].port_1, dpRetDuc.port_a); connect(splSupRoo.port_3, VAVBox[1:(numZon-1)].port_aAir); connect(splRetRoo.port_3, port_retAir[1:(numZon-1)]); for i in 1:(numZon - 2) loop connect(splSupRoo[i].port_2, splSupRoo[i+1].port_1); connect(splRetRoo[i].port_2, splRetRoo[i+1].port_1); end for; connect(splSupRoo[numZon-1].port_2, VAVBox[numZon].port_aAir); connect(splRetRoo[numZon-1].port_2, port_retAir[numZon]); connect(cooCoi.port_b2, dpSupDuc.port_a); connect(dpSupDuc.port_b, fanSup.port_a); end PartialHVAC;

model RoomLeakage "Room leakage model" extends Buildings.BaseClasses.BaseIcon; replaceable package Medium = Modelica.Media.Interfaces.PartialMedium "Medium in the component"; parameter Modelica.Units.SI.Volume VRoo "Room volume"; parameter Boolean use_windPressure=false "Set to true to enable wind pressure"; Buildings.Fluid.FixedResistances.PressureDrop res( redeclare package Medium = Medium, dp_nominal=50, m_flow_nominal=VRoo*1.2/3600) "Resistance model"; Modelica.Fluid.Interfaces.FluidPort_b port_b(redeclare package Medium = Medium); Buildings.Fluid.Sources.Outside_CpLowRise amb(redeclare package Medium = Medium, nPorts=1, s=s, azi=azi, Cp0=if use_windPressure then 0.6 else 0); BoundaryConditions.WeatherData.Bus weaBus "Bus with weather data"; Buildings.Fluid.Sensors.MassFlowRate senMasFlo1(redeclare package Medium = Medium, allowFlowReversal=true) "Sensor for mass flow rate"; Modelica.Blocks.Math.Gain ACHInf(k=1/VRoo/1.2*3600, y(unit="1/h")) "Air change per hour due to infiltration"; parameter Real s "Side ratio, s=length of this wall/length of adjacent wall"; parameter Modelica.Units.SI.Angle azi "Surface azimuth (South:0, West:pi/2)"; equation connect(res.port_b, port_b); connect(amb.weaBus, weaBus); connect(amb.ports[1], senMasFlo1.port_a); connect(senMasFlo1.port_b, res.port_a); connect(senMasFlo1.m_flow, ACHInf.u); end RoomLeakage;

model VAVReheatBox "Supply box of a VAV system with a hot water reheat coil" extends Modelica.Blocks.Icons.Block; replaceable package MediumA = Modelica.Media.Interfaces.PartialMedium "Medium model for air"; replaceable package MediumW = Modelica.Media.Interfaces.PartialMedium "Medium model for water"; parameter Boolean allowFlowReversal=true "= false to simplify equations, assuming, but not enforcing, no flow reversal"; parameter Modelica.Units.SI.MassFlowRate mCooAir_flow_nominal "Nominal air mass flow rate from cooling sizing calculations"; parameter Modelica.Units.SI.MassFlowRate mHeaAir_flow_nominal "Nominal air mass flow rate from heating sizing calculations"; final parameter Modelica.Units.SI.MassFlowRate mHeaWat_flow_nominal= QHea_flow_nominal/(cpWatLiq*(THeaWatInl_nominal - THeaWatOut_nominal)) "Nominal mass flow rate of hot water to reheat coil"; parameter Modelica.Units.SI.Volume VRoo "Room volume"; parameter Modelica.Units.SI.Temperature THeaWatInl_nominal(start=55 + 273.15, displayUnit="degC") "Reheat coil nominal inlet water temperature"; parameter Modelica.Units.SI.Temperature THeaWatOut_nominal(start= THeaWatInl_nominal - 10, displayUnit="degC") "Reheat coil nominal outlet water temperature"; parameter Modelica.Units.SI.Temperature THeaAirInl_nominal(start=12 + 273.15, displayUnit="degC") "Inlet air nominal temperature into VAV box during heating"; parameter Modelica.Units.SI.Temperature THeaAirDis_nominal(start=28 + 273.15, displayUnit="degC") "Discharge air temperature from VAV box during heating"; parameter Modelica.Units.SI.HeatFlowRate QHea_flow_nominal= mHeaAir_flow_nominal * cpAir * (THeaAirDis_nominal-THeaAirInl_nominal) "Nominal heating heat flow rate"; Modelica.Fluid.Interfaces.FluidPort_a port_aAir( redeclare package Medium=MediumA) "Fluid connector a1 (positive design flow direction is from port_a1 to port_b1)"; Modelica.Fluid.Interfaces.FluidPort_a port_bAir( redeclare package Medium=MediumA) "Fluid connector b (positive design flow direction is from port_a1 to port_b1)"; Modelica.Blocks.Interfaces.RealInput yVAV(final unit="1") "Signal for VAV damper"; Modelica.Blocks.Interfaces.RealOutput y_actual(final unit="1") "Actual VAV damper position"; Modelica.Fluid.Interfaces.FluidPort_a port_aHeaWat(redeclare package Medium = MediumW) "Hot water inlet port"; Modelica.Fluid.Interfaces.FluidPort_b port_bHeaWat(redeclare package Medium = MediumW) "Hot water outlet port"; Modelica.Blocks.Interfaces.RealOutput TSup( final unit = "K", displayUnit = "degC") "Supply Air Temperature"; Modelica.Blocks.Interfaces.RealOutput VSup_flow( final unit="m3/s") "Supply Air Volumetric Flow Rate"; Buildings.Fluid.Actuators.Dampers.PressureIndependent vav( redeclare package Medium = MediumA, m_flow_nominal=mCooAir_flow_nominal, dpDamper_nominal=20, allowFlowReversal=allowFlowReversal, dpFixed_nominal=130) "VAV box for room"; Buildings.Fluid.HeatExchangers.DryCoilEffectivenessNTU terHea( redeclare package Medium1 = MediumW, redeclare package Medium2 = MediumA, m1_flow_nominal=mHeaWat_flow_nominal, m2_flow_nominal=mHeaAir_flow_nominal, Q_flow_nominal=QHea_flow_nominal, configuration=Buildings.Fluid.Types.HeatExchangerConfiguration.CounterFlow, dp1_nominal=0, from_dp2=true, dp2_nominal=0, allowFlowReversal1=false, allowFlowReversal2=allowFlowReversal, T_a1_nominal=THeaWatInl_nominal, T_a2_nominal=THeaAirInl_nominal) "Reheat coil"; Fluid.Sensors.TemperatureTwoPort senTem( redeclare package Medium = MediumA, initType=Modelica.Blocks.Types.Init.InitialState, m_flow_nominal=mCooAir_flow_nominal, allowFlowReversal=allowFlowReversal) "Supply air temperature sensor"; Fluid.Sensors.VolumeFlowRate senVolFlo( redeclare package Medium = MediumA, initType=Modelica.Blocks.Types.Init.InitialState, m_flow_nominal=mCooAir_flow_nominal, allowFlowReversal=allowFlowReversal) "Supply air volumetric flow rate sensor"; Fluid.Actuators.Valves.TwoWayEqualPercentage val( redeclare package Medium = MediumW, allowFlowReversal=false, m_flow_nominal=mHeaWat_flow_nominal, from_dp=true, dpValve_nominal=3000, use_inputFilter=false, dpFixed_nominal=3000) "Valve for terminal heater"; Modelica.Blocks.Interfaces.RealInput yHea "Actuator position for heating valve (0: closed, 1: open)"; Real ACH(unit="1/h") = VSup_flow/VRoo*3600 "Air changes per hour"; protected constant Modelica.Units.SI.SpecificHeatCapacity cpAir=Buildings.Utilities.Psychrometrics.Constants.cpAir "Air specific heat capacity"; constant Modelica.Units.SI.SpecificHeatCapacity cpWatLiq=Buildings.Utilities.Psychrometrics.Constants.cpWatLiq "Water specific heat capacity"; equation connect(vav.y, yVAV); connect(vav.y_actual, y_actual); connect(port_aAir, terHea.port_a2); connect(vav.port_a, terHea.port_b2); connect(port_bHeaWat, terHea.port_b1); connect(vav.port_b, senTem.port_a); connect(senTem.port_b, senVolFlo.port_a); connect(senVolFlo.port_b, port_bAir); connect(senVolFlo.V_flow, VSup_flow); connect(senTem.T, TSup); connect(port_aHeaWat, val.port_a); connect(val.port_b, terHea.port_a1); connect(yHea, val.y); end VAVReheatBox;

model Results "Model to store the results of the simulation" parameter Modelica.Units.SI.Area A "Floor area"; input Modelica.Units.SI.Power PFan "Fan energy"; input Modelica.Units.SI.Power PPum "Pump energy"; input Modelica.Units.SI.Power PHea "Heating energy"; input Modelica.Units.SI.Power PCooSen "Sensible cooling energy"; input Modelica.Units.SI.Power PCooLat "Latent cooling energy"; Real EFan( unit="J/m2", start=0, nominal=1E5, fixed=true) "Fan energy"; Real EPum( unit="J/m2", start=0, nominal=1E5, fixed=true) "Pump energy"; Real EHea( unit="J/m2", start=0, nominal=1E5, fixed=true) "Heating energy"; Real ECooSen( unit="J/m2", start=0, nominal=1E5, fixed=true) "Sensible cooling energy"; Real ECooLat( unit="J/m2", start=0, nominal=1E5, fixed=true) "Latent cooling energy"; Real ECoo(unit="J/m2") "Total cooling energy"; equation A*der(EFan) = PFan; A*der(EPum) = PPum; A*der(EHea) = PHea; A*der(ECooSen) = PCooSen; A*der(ECooLat) = PCooLat; ECoo = ECooSen + ECooLat; end Results;