Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits
Control sequences for terminal units
Information
This package contains control sequences for terminal units.
Package Content
| Name | Description |
|---|---|
 Controller
|
Controller for room VAV box |
 ModeAndSetPoints
|
Output zone setpoint with operation mode selection |
 Reheat
|
Sequences for VAV reheat terminal unit |
 SetPoints
|
Generic sequences of generating setpoints for terminal units control |
 Validation
|
Collection of validation models |
Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.Controller
Controller for room VAV box
Information
Controller for terminal box of VAV system with reheat according to ASHRAE
Guideline 36, Part 5.E. It outputs damper position yDam,
hot water valve position yVal, AHU cooling supply temperature
setpoint reset request yZonTemResReq, and static pressure setpoint
reset request yZonPreResReq.
The sequence consists of four subsequences.
a. Heating and cooling control loop
The subsequence is implementd according to Part 5.B.5. The measured zone
temperature TZon, zone setpoints temperatures TZonHeaSet and
TZonCooSet are inputs to the block conHeaLoo and
conCooLoo to generate the control loop signal.
b. Active airflow setpoint calculation
This sequence sets the active maximum and minimum airflow according to
Part 5.E.3-5. Depending on operation modes uOpeMod, it sets the
airflow rate limits for cooling and heating supply. See
Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.Reheat.SetPoints.ActiveAirFlow.
c. Damper and valve control
This sequence sets the damper and valve position for VAV reheat terminal unit.
The implementation is according to Part 5.E.6. According to heating and cooling
control loop signal, it calculates the discharge air temperature setpoint
TDisHeaSet. Along with the defined maximum and minimum airflow, measured
zone temperature, the sequence outputs yDam, yVal,
TDisHeaSet and discharge airflow rate setpoint VDisSet_flow.
See
Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.Reheat.DamperValves.
d. System reset requests generation
According to Part 5.E.9, this sequence outputs the system reset requests, i.e.
cooling supply air temperature reset requests yZonTemResReq,
static pressure reset requests yZonPreResReq, hot water reset
requests yHeaValResReq, and the boiler plant reset requests
yHeaPlaReq. See
Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.Reheat.SystemRequests.
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| Real | samplePeriod | samplePeriod(final unit="s",... | Sample period of component, set to the same value as the trim and respond that process yPreSetReq [s] |
| Real | V_flow_nominal | V_flow_nominal(final unit="m... | Volume flow rate of this thermal zone [m3/s] |
| Real | AFlo | AFlo(final unit="m2", final ... | Area of the zone [m2] |
| Cooling loop signal | |||
| SimpleController | controllerTypeCoo | Buildings.Controls.OBC.CDL.T... | Type of controller |
| Real | kCoo | 0.1 | Gain for cooling control loop signal [1/K] |
| Real | TiCoo | 900 | Time constant of integrator block for cooling control loop signal [s] |
| Real | TdCoo | 0.1 | Time constant of derivative block for cooling control loop signal [s] |
| Heating loop signal | |||
| SimpleController | controllerTypeHea | Buildings.Controls.OBC.CDL.T... | Type of controller |
| Real | kHea | 0.1 | Gain for heating control loop signal [1/K] |
| Real | TiHea | 900 | Time constant of integrator block for heating control loop signal [s] |
| Real | TdHea | 0.1 | Time constant of derivative block for heating control loop signal [s] |
| Valve | |||
| SimpleController | controllerTypeVal | Buildings.Controls.OBC.CDL.T... | Type of controller |
| Real | kVal | 0.5 | Gain of controller for valve control |
| Real | TiVal | 300 | Time constant of integrator block for valve control [s] |
| Real | TdVal | 0.1 | Time constant of derivative block for valve control [s] |
| Damper | |||
| SimpleController | controllerTypeDam | Buildings.Controls.OBC.CDL.T... | Type of controller |
| Real | kDam | 0.5 | Gain of controller for damper control [1] |
| Real | TiDam | 300 | Time constant of integrator block for damper control [s] |
| Real | TdDam | 0.1 | Time constant of derivative block for damper control [s] |
| Airflow setpoint | |||
| Zone sensors | |||
| Boolean | have_occSen | false | Set to true if the zone has occupancy sensor |
| Boolean | have_winSen | false | Set to true if the zone has window status sensor |
| Boolean | have_CO2Sen | false | Set to true if the zone has CO2 sensor |
| Nominal conditions | |||
| Real | VDisCooSetMax_flow | V_flow_nominal | Zone maximum cooling airflow setpoint [m3/s] |
| Real | VDisSetMin_flow | 0.15*V_flow_nominal | Zone minimum airflow setpoint [m3/s] |
| Real | VDisHeaSetMax_flow | V_flow_nominal | Zone maximum heating airflow setpoint [m3/s] |
| Real | VDisConMin_flow | 0.1*V_flow_nominal | VAV box controllable minimum [m3/s] |
| Real | VOutPerAre_flow | 3e-4 | Outdoor air rate per unit area [m3/(s.m2)] |
| Real | VOutPerPer_flow | 2.5e-3 | Outdoor air rate per person [m3/s] |
| Real | CO2Set | 894 | CO2 setpoint in ppm |
| Damper and valve | |||
| Parameters | |||
| Real | dTDisZonSetMax | 11 | Zone maximum discharge air temperature above heating setpoint [K] |
| Real | TDisMin | 283.15 | Lowest discharge air temperature [K] |
| System requests | |||
| Parameters | |||
| Boolean | have_heaWatCoi | true | Flag, true if there is a hot water coil |
| Boolean | have_heaPla | false | Flag, true if there is a boiler plant |
| Real | errTZonCoo_1 | 2.8 | Limit value of difference between zone temperature and cooling setpoint for generating 3 cooling SAT reset requests [K] |
| Real | errTZonCoo_2 | 1.7 | Limit value of difference between zone temperature and cooling setpoint for generating 2 cooling SAT reset requests [K] |
| Real | errTDis_1 | 17 | Limit value of difference between discharge air temperature and its setpoint for generating 3 hot water reset requests [K] |
| Real | errTDis_2 | 8.3 | Limit value of difference between discharge air temperature and its setpoint for generating 2 hot water reset requests [K] |
| Duration times | |||
| Real | durTimTem | 120 | Duration time of zone temperature exceeds setpoint [s] |
| Real | durTimFlo | 60 | Duration time of airflow rate less than setpoint [s] |
| Real | durTimDisAir | 300 | Duration time of discharge air temperature is less than setpoint [s] |
Connectors
| Type | Name | Description |
|---|---|---|
| input RealInput | TZonHeaSet | Setpoint temperature for room for heating [K] |
| input RealInput | TZonCooSet | Setpoint temperature for room for cooling [K] |
| input RealInput | TZon | Measured room temperature [K] |
| input RealInput | TDis | Measured supply air temperature after heating coil [K] |
| input RealInput | VDis_flow | Measured discharge airflow rate [m3/s] |
| input RealInput | TSupAHU | AHU supply air temperature [K] |
| input RealInput | ppmCO2 | Measured CO2 concentration |
| input RealInput | nOcc | Number of occupants |
| input BooleanInput | uWin | Window status, true if open, false if closed |
| input IntegerInput | uOpeMod | Zone operation mode |
| input RealInput | yDam_actual | Actual VAV damper position |
| output RealOutput | yVal | Signal for heating coil valve [1] |
| output RealOutput | yDam | Signal for VAV damper [1] |
| output IntegerOutput | yZonTemResReq | Zone cooling supply air temperature reset request |
| output IntegerOutput | yZonPreResReq | Zone static pressure reset requests |
Modelica definition
block Controller "Controller for room VAV box"
parameter Real samplePeriod(
final unit="s",
final quantity="Time")
"Sample period of component, set to the same value as the trim and respond that process yPreSetReq";
parameter Real V_flow_nominal(
final unit="m3/s",
final quantity="VolumeFlowRate")
"Volume flow rate of this thermal zone";
parameter Real AFlo(
final unit="m2",
final quantity="Area") "Area of the zone";
parameter Buildings.Controls.OBC.CDL.Types.SimpleController controllerTypeCoo=
Buildings.Controls.OBC.CDL.Types.SimpleController.PI "Type of controller";
parameter Real kCoo(final unit="1/K") = 0.1
"Gain for cooling control loop signal";
parameter Real TiCoo(
final unit="s",
final quantity="Time")=900
"Time constant of integrator block for cooling control loop signal";
parameter Real TdCoo(
final unit="s",
final quantity="Time")=0.1
"Time constant of derivative block for cooling control loop signal";
parameter Buildings.Controls.OBC.CDL.Types.SimpleController controllerTypeHea=
Buildings.Controls.OBC.CDL.Types.SimpleController.PI
"Type of controller";
parameter Real kHea(final unit="1/K")=0.1
"Gain for heating control loop signal";
parameter Real TiHea(
final unit="s",
final quantity="Time")=900
"Time constant of integrator block for heating control loop signal";
parameter Real TdHea(
final unit="s",
final quantity="Time")=0.1
"Time constant of derivative block for heating control loop signal";
parameter Buildings.Controls.OBC.CDL.Types.SimpleController controllerTypeVal=
Buildings.Controls.OBC.CDL.Types.SimpleController.PI
"Type of controller";
parameter Real kVal=0.5
"Gain of controller for valve control";
parameter Real TiVal(
final unit="s",
final quantity="Time")=300
"Time constant of integrator block for valve control";
parameter Real TdVal(
final unit="s",
final quantity="Time")=0.1
"Time constant of derivative block for valve control";
parameter Buildings.Controls.OBC.CDL.Types.SimpleController controllerTypeDam=
Buildings.Controls.OBC.CDL.Types.SimpleController.PI
"Type of controller";
parameter Real kDam(final unit="1")=0.5
"Gain of controller for damper control";
parameter Real TiDam(
final unit="s",
final quantity="Time")=300
"Time constant of integrator block for damper control";
parameter Real TdDam(
final unit="s",
final quantity="Time")=0.1
"Time constant of derivative block for damper control";
parameter Boolean have_occSen=false
"Set to true if the zone has occupancy sensor";
parameter Boolean have_winSen=false
"Set to true if the zone has window status sensor";
parameter Boolean have_CO2Sen=false
"Set to true if the zone has CO2 sensor";
parameter Real VDisCooSetMax_flow(
final unit="m3/s",
final quantity="VolumeFlowRate")=V_flow_nominal
"Zone maximum cooling airflow setpoint";
parameter Real VDisSetMin_flow(
final unit="m3/s",
final quantity="VolumeFlowRate")=0.15*V_flow_nominal
"Zone minimum airflow setpoint";
parameter Real VDisHeaSetMax_flow(
final unit="m3/s",
final quantity="VolumeFlowRate")=V_flow_nominal
"Zone maximum heating airflow setpoint";
parameter Real VDisConMin_flow(
final unit="m3/s",
final quantity="VolumeFlowRate")=0.1*V_flow_nominal
"VAV box controllable minimum";
parameter Real VOutPerAre_flow(final unit = "m3/(s.m2)")=3e-4
"Outdoor air rate per unit area";
parameter Real VOutPerPer_flow(
final unit="m3/s",
final quantity="VolumeFlowRate")=2.5e-3
"Outdoor air rate per person";
parameter Real CO2Set=894 "CO2 setpoint in ppm";
parameter Real dTDisZonSetMax(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=11
"Zone maximum discharge air temperature above heating setpoint";
parameter Real TDisMin(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=283.15
"Lowest discharge air temperature";
parameter Boolean have_heaWatCoi=true
"Flag, true if there is a hot water coil";
parameter Boolean have_heaPla=false
"Flag, true if there is a boiler plant";
parameter Real errTZonCoo_1(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=2.8
"Limit value of difference between zone temperature and cooling setpoint
for generating 3 cooling SAT reset requests";
parameter Real errTZonCoo_2(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=1.7
"Limit value of difference between zone temperature and cooling setpoint
for generating 2 cooling SAT reset requests";
parameter Real errTDis_1(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=17
"Limit value of difference between discharge air temperature and its setpoint
for generating 3 hot water reset requests";
parameter Real errTDis_2(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=8.3
"Limit value of difference between discharge air temperature and its setpoint
for generating 2 hot water reset requests";
parameter Real durTimTem(
final unit="s",
final quantity="Time")=120
"Duration time of zone temperature exceeds setpoint";
parameter Real durTimFlo(
final unit="s",
final quantity="Time")=60
"Duration time of airflow rate less than setpoint";
parameter Real durTimDisAir(
final unit="s",
final quantity="Time")=300
"Duration time of discharge air temperature is less than setpoint";
Buildings.Controls.OBC.CDL.Interfaces.RealInput TZonHeaSet(
final quantity="ThermodynamicTemperature",
final unit = "K",
final displayUnit = "degC")
"Setpoint temperature for room for heating";
Buildings.Controls.OBC.CDL.Interfaces.RealInput TZonCooSet(
final quantity="ThermodynamicTemperature",
final unit = "K",
final displayUnit = "degC")
"Setpoint temperature for room for cooling";
Buildings.Controls.OBC.CDL.Interfaces.RealInput TZon(
final quantity="ThermodynamicTemperature",
final unit = "K",
final displayUnit = "degC")
"Measured room temperature";
Buildings.Controls.OBC.CDL.Interfaces.RealInput TDis(
final quantity="ThermodynamicTemperature",
final unit = "K",
final displayUnit = "degC")
"Measured supply air temperature after heating coil";
Buildings.Controls.OBC.CDL.Interfaces.RealInput VDis_flow(
final unit="m3/s",
final quantity="VolumeFlowRate")
"Measured discharge airflow rate";
Buildings.Controls.OBC.CDL.Interfaces.RealInput TSupAHU(
final quantity="ThermodynamicTemperature",
final unit = "K",
final displayUnit = "degC")
"AHU supply air temperature";
Buildings.Controls.OBC.CDL.Interfaces.RealInput ppmCO2 if have_CO2Sen
"Measured CO2 concentration";
Buildings.Controls.OBC.CDL.Interfaces.RealInput nOcc if have_occSen
"Number of occupants";
Buildings.Controls.OBC.CDL.Interfaces.BooleanInput uWin if have_winSen
"Window status, true if open, false if closed";
Buildings.Controls.OBC.CDL.Interfaces.IntegerInput uOpeMod
"Zone operation mode";
Buildings.Controls.OBC.CDL.Interfaces.RealInput yDam_actual
"Actual VAV damper position";
Buildings.Controls.OBC.CDL.Interfaces.RealOutput yVal(
final min=0,
final max=1,
final unit="1")
"Signal for heating coil valve";
Buildings.Controls.OBC.CDL.Interfaces.RealOutput yDam(
final min=0,
final max=1,
final unit="1")
"Signal for VAV damper";
Buildings.Controls.OBC.CDL.Interfaces.IntegerOutput yZonTemResReq
"Zone cooling supply air temperature reset request";
Buildings.Controls.OBC.CDL.Interfaces.IntegerOutput yZonPreResReq
"Zone static pressure reset requests";
Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.Reheat.SetPoints.ActiveAirFlow
actAirSet(
final AFlo=AFlo,
final have_occSen=have_occSen,
final have_winSen=have_winSen,
final have_CO2Sen=have_CO2Sen,
final VDisCooSetMax_flow=VDisCooSetMax_flow,
final VDisSetMin_flow=VDisSetMin_flow,
final VDisHeaSetMax_flow=VDisHeaSetMax_flow,
final VDisConMin_flow=VDisConMin_flow,
final VOutPerAre_flow=VOutPerAre_flow,
final VOutPerPer_flow=VOutPerPer_flow,
final CO2Set=CO2Set)
"Active airflow rate setpoint";
Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.Reheat.DamperValves damVal(
final controllerTypeVal=controllerTypeVal,
final kVal=kVal,
final TiVal=TiVal,
final TdVal=TdVal,
final controllerTypeDam=controllerTypeDam,
final kDam=kDam,
final TiDam=TiDam,
final TdDam=TdDam,
final dTDisZonSetMax=dTDisZonSetMax,
final TDisMin=TDisMin,
V_flow_nominal=max(VDisCooSetMax_flow, VDisHeaSetMax_flow))
"Damper and valve controller";
Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.Reheat.SystemRequests sysReq(
final samplePeriod=samplePeriod,
final have_heaWatCoi=have_heaWatCoi,
final have_heaPla=have_heaPla,
final errTZonCoo_1=errTZonCoo_1,
final errTZonCoo_2=errTZonCoo_2,
final errTDis_1=errTDis_1,
final errTDis_2=errTDis_2,
final durTimTem=durTimTem,
final durTimFlo=durTimFlo,
final durTimDisAir=durTimDisAir)
"Number of system requests";
Buildings.Controls.OBC.CDL.Continuous.LimPID conHeaLoo(
final controllerType=controllerTypeHea,
final k=kHea,
final Ti=TiHea,
final Td=TdHea,
final yMax=1,
final yMin=0,
reset=Buildings.Controls.OBC.CDL.Types.Reset.Parameter) "Heating loop signal";
Buildings.Controls.OBC.CDL.Continuous.LimPID conCooLoo(
final controllerType=controllerTypeCoo,
final k=kCoo,
final Ti=TiCoo,
final Td=TdCoo,
final yMax=1,
final yMin=0,
reverseAction=true,
reset=Buildings.Controls.OBC.CDL.Types.Reset.Parameter) "Cooling loop signal";
protected
Buildings.Controls.OBC.CDL.Integers.Equal isUnOcc
"Output true if unoccupied";
Buildings.Controls.OBC.CDL.Integers.Sources.Constant conIntUn(
final k=Buildings.Controls.OBC.ASHRAE.G36_PR1.Types.OperationModes.unoccupied)
"Constant signal for unoccupied mode";
Buildings.Controls.OBC.CDL.Logical.Not isNotUn
"Output true if not unoccupied";
equation
connect(sysReq.TZonCooSet, TZonCooSet);
connect(sysReq.TZon, TZon);
connect(sysReq.VDisSet_flow, damVal.VDisSet_flow);
connect(sysReq.VDis_flow, VDis_flow);
connect(sysReq.TDisHeaSet, damVal.TDisHeaSet);
connect(damVal.yDam, yDam);
connect(damVal.yHeaVal, yVal);
connect(damVal.VDis_flow, VDis_flow);
connect(damVal.TDis, TDis);
connect(sysReq.TDis, TDis);
connect(damVal.yHeaVal, sysReq.uHeaVal);
connect(TZon, damVal.TZon);
connect(damVal.TSup, TSupAHU);
connect(actAirSet.VActCooMax_flow, damVal.VActCooMax_flow);
connect(actAirSet.VActCooMin_flow, damVal.VActCooMin_flow);
connect(actAirSet.VActMin_flow, damVal.VActMin_flow);
connect(actAirSet.VActHeaMin_flow, damVal.VActHeaMin_flow);
connect(actAirSet.VActHeaMax_flow, damVal.VActHeaMax_flow);
connect(damVal.THeaSet, TZonHeaSet);
connect(actAirSet.VActCooMax_flow, damVal.VActCooMax_flow);
connect(actAirSet.VActCooMin_flow, damVal.VActCooMin_flow);
connect(actAirSet.VActMin_flow, damVal.VActMin_flow);
connect(actAirSet.VActHeaMin_flow, damVal.VActHeaMin_flow);
connect(actAirSet.VActHeaMax_flow, damVal.VActHeaMax_flow);
connect(actAirSet.uOpeMod, uOpeMod);
connect(sysReq.yZonTemResReq, yZonTemResReq);
connect(sysReq.yZonPreResReq, yZonPreResReq);
connect(actAirSet.ppmCO2, ppmCO2);
connect(actAirSet.nOcc, nOcc);
connect(actAirSet.uWin, uWin);
connect(TZonHeaSet, conHeaLoo.u_s);
connect(TZonCooSet, conCooLoo.u_s);
connect(TZon, conHeaLoo.u_m);
connect(TZon, conCooLoo.u_m);
connect(conCooLoo.y, damVal.uCoo);
connect(conHeaLoo.y, damVal.uHea);
connect(conCooLoo.y, sysReq.uCoo);
connect(damVal.uOpeMod, uOpeMod);
connect(conIntUn.y, isUnOcc.u1);
connect(uOpeMod, isUnOcc.u2);
connect(isUnOcc.y, isNotUn.u);
connect(isNotUn.y, conCooLoo.trigger);
connect(isNotUn.y, conHeaLoo.trigger);
connect(sysReq.yDam_actual,yDam_actual);
end Controller;
Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.ModeAndSetPoints
Output zone setpoint with operation mode selection
Information
Block that outputs the zone setpoint temperature (TZonCooSet, TZonHeaSet)
and system operation mode (yOpeMod). When operation mode is in freeze
protection setback mode, it also outputs a level 3 freeze protection alarm
yFreProSta. The sequences are implemented according to ASHRAE
Guideline 36, Part 5.B.3 and 5.C.6.
The sequence consists of the following two subsequences.
Operation mode selector
The subsequence outputs one of seven types of system operation mode (occupied, warmup,
cool-down, setback, freeze protection setback, setup, unoccupied) according
to current time, the time to next occupied hours tNexOcc and
current zone temperature TZon.
See
Buildings.Controls.OBC.ASHRAE.G36_PR1.Generic.SetPoints.OperationMode.
Zone setpoint temperature reset
This sequence is implemented according to Part 5.B.3. It sets the zone temperature setpoint according to the globally specified setpoints, the local setpoint adjustments, the demand limits adjustment, the window status and the occupancy status. See Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.SetPoints.ZoneTemperatures.
Usage
This version is for a single zone only to be used in the Single Zone VAV sequence. For multizone systems, use Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.ModeAndSetPoints.
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| Real | TZonHeaOn | 293.15 | Heating setpoint during on [K] |
| Real | TZonHeaOff | 285.15 | Heating setpoint during off [K] |
| Real | TZonCooOn | 297.15 | Cooling setpoint during on [K] |
| Real | TZonCooOff | 303.15 | Cooling setpoint during off [K] |
| Operation mode | |||
| Parameters | |||
| Real | preWarCooTim | 10800 | Maximum cool-down/warm-up time [s] |
| Real | bouLim | 1.1 | Value limit to indicate the end of setback/setup mode [K] |
| Real | TZonFreProOn | 277.55 | Threshold zone temperature value to activate freeze protection mode [K] |
| Real | TZonFreProOff | 280.35 | Threshold zone temperature value to finish the freeze protection mode [K] |
| Test setting | |||
| Real | warCooTim | 1800 | Defined cool-down/warm-up time [s] |
| Setpoint adjust | |||
| Sensors | |||
| Boolean | have_occSen | false | Check if the zone has occupancy sensor |
| Boolean | have_winSen | false | Check if the zone has window status sensor |
| Adjustable settings | |||
| Boolean | cooAdj | false | Flag, set to true if both cooling and heating setpoint are adjustable separately |
| Boolean | heaAdj | false | Flag, set to true if heating setpoint is adjustable |
| Boolean | sinAdj | false | Flag, set to true if both cooling and heating setpoint are adjustable through a single common knob |
| Boolean | ignDemLim | true | Flag, set to true to exempt individual zone from demand limit setpoint adjustment |
| Limits | |||
| Real | TZonCooOnMax | 300.15 | Maximum cooling setpoint during on [K] |
| Real | TZonCooOnMin | 295.15 | Minimum cooling setpoint during on [K] |
| Real | TZonHeaOnMax | 295.15 | Maximum heating setpoint during on [K] |
| Real | TZonHeaOnMin | 291.15 | Minimum heating setpoint during on [K] |
| Real | TZonCooSetWinOpe | 322.15 | Cooling setpoint when window is open [K] |
| Real | TZonHeaSetWinOpe | 277.15 | Heating setpoint when window is open [K] |
| Demands settings | |||
| Real | incTSetDem_1 | 0.56 | Cooling setpoint increase value when cooling demand limit level 1 is imposed [K] |
| Real | incTSetDem_2 | 1.1 | Cooling setpoint increase value when cooling demand limit level 2 is imposed [K] |
| Real | incTSetDem_3 | 2.2 | Cooling setpoint increase value when cooling demand limit level 3 is imposed [K] |
| Real | decTSetDem_1 | 0.56 | Heating setpoint decrease value when heating demand limit level 1 is imposed [K] |
| Real | decTSetDem_2 | 1.1 | Heating setpoint decrease value when heating demand limit level 2 is imposed [K] |
| Real | decTSetDem_3 | 2.2 | Heating setpoint decrease value when heating demand limit level 3 is imposed [K] |
| Integer | cooDemLimLevCon | Buildings.Controls.OBC.ASHRA... | Cooling demand limit level |
| Integer | heaDemLimLevCon | Buildings.Controls.OBC.ASHRA... | Heating demand limit level |
| Boolean | winStaCon | false | Window status, set to true if window is open |
Connectors
| Type | Name | Description |
|---|---|---|
| input RealInput | tNexOcc | Time to next occupied period [s] |
| input BooleanInput | uOcc | Current occupancy period, true if it is in occupant period |
| input RealInput | TZon | Measured zone temperatures [K] |
| input RealInput | setAdj | Setpoint adjustment value [K] |
| input RealInput | heaSetAdj | Heating setpoint adjustment value [K] |
| input BooleanInput | uOccSen | Occupancy sensor (occupied=true, unoccupied=false) |
| input BooleanInput | uWinSta | Window status (open=true, close=false) |
| output RealOutput | TZonCooSet | Cooling setpoint temperature [K] |
| output RealOutput | TZonHeaSet | Heating setpoint temperature [K] |
| output IntegerOutput | yOpeMod | Operation mode |
Modelica definition
block ModeAndSetPoints
"Output zone setpoint with operation mode selection"
parameter Real TZonHeaOn(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=293.15
"Heating setpoint during on";
parameter Real TZonHeaOff(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=285.15
"Heating setpoint during off";
parameter Real TZonCooOn(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=297.15
"Cooling setpoint during on";
parameter Real TZonCooOff(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=303.15
"Cooling setpoint during off";
parameter Real preWarCooTim(
final unit="s",
final quantity="Time")=10800
"Maximum cool-down/warm-up time";
parameter Real bouLim(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=1.1
"Value limit to indicate the end of setback/setup mode";
parameter Real TZonFreProOn(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=277.55
"Threshold zone temperature value to activate freeze protection mode";
parameter Real TZonFreProOff(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=280.35
"Threshold zone temperature value to finish the freeze protection mode";
parameter Real warCooTim(
final unit="s",
final quantity="Time")=1800
"Defined cool-down/warm-up time";
parameter Boolean have_occSen=false
"Check if the zone has occupancy sensor";
parameter Boolean have_winSen=false
"Check if the zone has window status sensor";
parameter Boolean cooAdj=false
"Flag, set to true if both cooling and heating setpoint are adjustable separately";
parameter Boolean heaAdj=false
"Flag, set to true if heating setpoint is adjustable";
parameter Boolean sinAdj=false
"Flag, set to true if both cooling and heating setpoint are adjustable through a single common knob";
parameter Boolean ignDemLim=true
"Flag, set to true to exempt individual zone from demand limit setpoint adjustment";
parameter Real TZonCooOnMax(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=300.15
"Maximum cooling setpoint during on";
parameter Real TZonCooOnMin(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=295.15
"Minimum cooling setpoint during on";
parameter Real TZonHeaOnMax(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=295.15
"Maximum heating setpoint during on";
parameter Real TZonHeaOnMin(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=291.15
"Minimum heating setpoint during on";
parameter Real TZonCooSetWinOpe(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=322.15
"Cooling setpoint when window is open";
parameter Real TZonHeaSetWinOpe(
final unit="K",
final displayUnit="degC",
final quantity="ThermodynamicTemperature")=277.15
"Heating setpoint when window is open";
parameter Real incTSetDem_1(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=0.56
"Cooling setpoint increase value when cooling demand limit level 1 is imposed";
parameter Real incTSetDem_2(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=1.1
"Cooling setpoint increase value when cooling demand limit level 2 is imposed";
parameter Real incTSetDem_3(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=2.2
"Cooling setpoint increase value when cooling demand limit level 3 is imposed";
parameter Real decTSetDem_1(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=0.56
"Heating setpoint decrease value when heating demand limit level 1 is imposed";
parameter Real decTSetDem_2(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=1.1
"Heating setpoint decrease value when heating demand limit level 2 is imposed";
parameter Real decTSetDem_3(
final unit="K",
final displayUnit="K",
final quantity="TemperatureDifference")=2.2
"Heating setpoint decrease value when heating demand limit level 3 is imposed";
parameter Integer cooDemLimLevCon=Buildings.Controls.OBC.ASHRAE.G36_PR1.Types.DemandLimitLevels.cooling0
"Cooling demand limit level";
parameter Integer heaDemLimLevCon=Buildings.Controls.OBC.ASHRAE.G36_PR1.Types.DemandLimitLevels.heating0
"Heating demand limit level";
parameter Boolean winStaCon=false
"Window status, set to true if window is open";
Buildings.Controls.OBC.CDL.Interfaces.RealInput tNexOcc(
final unit="s",
quantity="Time")
"Time to next occupied period";
Buildings.Controls.OBC.CDL.Interfaces.BooleanInput uOcc
"Current occupancy period, true if it is in occupant period";
Buildings.Controls.OBC.CDL.Interfaces.RealInput TZon(
final unit="K",
quantity="ThermodynamicTemperature")
"Measured zone temperatures";
Buildings.Controls.OBC.CDL.Interfaces.RealInput setAdj(
final unit="K",
quantity="ThermodynamicTemperature") if (cooAdj or sinAdj)
"Setpoint adjustment value";
Buildings.Controls.OBC.CDL.Interfaces.RealInput heaSetAdj(
final unit="K",
quantity="ThermodynamicTemperature") if heaAdj
"Heating setpoint adjustment value";
Buildings.Controls.OBC.CDL.Interfaces.BooleanInput uOccSen if have_occSen
"Occupancy sensor (occupied=true, unoccupied=false)";
Buildings.Controls.OBC.CDL.Interfaces.BooleanInput uWinSta if have_winSen
"Window status (open=true, close=false)";
Buildings.Controls.OBC.CDL.Interfaces.RealOutput TZonCooSet(
final unit="K",
quantity="ThermodynamicTemperature") "Cooling setpoint temperature";
Buildings.Controls.OBC.CDL.Interfaces.RealOutput TZonHeaSet(
final unit="K",
quantity="ThermodynamicTemperature") "Heating setpoint temperature";
Buildings.Controls.OBC.CDL.Interfaces.IntegerOutput yOpeMod
"Operation mode";
protected
Buildings.Controls.OBC.ASHRAE.G36_PR1.TerminalUnits.SetPoints.ZoneTemperatures
TZonSet(
final have_occSen=have_occSen,
final have_winSen=have_winSen,
final cooAdj=cooAdj,
final heaAdj=heaAdj,
final sinAdj=sinAdj,
final ignDemLim=ignDemLim,
final TZonCooOnMax=TZonCooOnMax,
final TZonCooOnMin=TZonCooOnMin,
final TZonHeaOnMax=TZonHeaOnMax,
final TZonHeaOnMin=TZonHeaOnMin,
final TZonCooSetWinOpe=TZonCooSetWinOpe,
final TZonHeaSetWinOpe=TZonHeaSetWinOpe,
final incTSetDem_1=incTSetDem_1,
final incTSetDem_2=incTSetDem_2,
final incTSetDem_3=incTSetDem_3,
final decTSetDem_1=decTSetDem_1,
final decTSetDem_2=decTSetDem_2,
final decTSetDem_3=decTSetDem_3) "Zone set point temperature";
Buildings.Controls.OBC.CDL.Integers.Sources.Constant cooDemLimLev(
final k=cooDemLimLevCon)
"Cooling demand limit level";
Buildings.Controls.OBC.CDL.Integers.Sources.Constant heaDemLimLev(
final k=heaDemLimLevCon) "Heating demand limit level";
Buildings.Controls.OBC.CDL.Continuous.Sources.Constant TSetRooHeaOn(
final k=TZonHeaOn)
"Heating on setpoint";
Buildings.Controls.OBC.CDL.Continuous.Sources.Constant TSetRooHeaOff(
final k=TZonHeaOff)
"Heating off set point";
Buildings.Controls.OBC.CDL.Continuous.Sources.Constant TSetRooCooOn(
final k=TZonCooOn)
"Cooling on setpoint";
Buildings.Controls.OBC.CDL.Continuous.Sources.Constant TSetRooCooOff(
final k=TZonCooOff)
"Cooling off set point";
Buildings.Controls.OBC.ASHRAE.G36_PR1.Generic.SetPoints.OperationMode
opeModSel(
final have_winSen=have_winSen,
final numZon=1,
final preWarCooTim=preWarCooTim,
final TZonFreProOn=TZonFreProOn,
final TZonFreProOff=TZonFreProOff) "Operation mode selector";
Buildings.Controls.OBC.CDL.Continuous.Sources.Constant tCooDowHeaUp(
final k=warCooTim) "Cool down and heat up time (simplified as constant)";
Buildings.Controls.OBC.ASHRAE.G36_PR1.Generic.SetPoints.ZoneStatus zonSta(
final have_winSen=have_winSen) "Check zone temperature status";
Buildings.Controls.OBC.CDL.Conversions.BooleanToInteger colZon
"Check if the zone is cold zone";
Buildings.Controls.OBC.CDL.Conversions.BooleanToInteger hotZon
"Check if the zone is hot zone";
equation
connect(TZonSet.uCooDemLimLev,cooDemLimLev. y);
connect(heaDemLimLev.y,TZonSet. uHeaDemLimLev);
connect(TZonSet.TZonCooSet, TZonCooSet);
connect(TZonSet.TZonHeaSet, TZonHeaSet);
connect(setAdj, TZonSet.setAdj);
connect(heaSetAdj, TZonSet.heaSetAdj);
connect(TZonSet.uOccSen, uOccSen);
connect(TZonSet.uWinSta, uWinSta);
connect(tCooDowHeaUp.y, zonSta.cooDowTim);
connect(tCooDowHeaUp.y, zonSta.warUpTim);
connect(uWinSta, zonSta.uWinSta);
connect(TSetRooHeaOn.y, zonSta.TZonHeaSetOcc);
connect(TSetRooCooOn.y, zonSta.TZonCooSetOcc);
connect(TZon, zonSta.TZonMax);
connect(TZon, zonSta.TZon);
connect(TZon, zonSta.TZonMin);
connect(TSetRooHeaOff.y, zonSta.TZonHeaSetUno);
connect(TSetRooCooOff.y, zonSta.TZonCooSetUno);
connect(uOcc, opeModSel.uOcc);
connect(tNexOcc, opeModSel.tNexOcc);
connect(zonSta.yCooTim, opeModSel.maxCooDowTim);
connect(zonSta.yWarTim, opeModSel.maxWarUpTim);
connect(zonSta.yOccHeaHigMin, opeModSel.occHeaHigMin);
connect(zonSta.yMaxHigOccCoo, opeModSel.maxHigOccCoo);
connect(zonSta.yUnoHeaHigMin, opeModSel.unoHeaHigMin);
connect(TZon, opeModSel.TZonMax);
connect(TZon, opeModSel.TZonMin);
connect(zonSta.yMaxHigUnoCoo, opeModSel.maxHigUnoCoo);
connect(zonSta.yLowUnoHea, colZon.u);
connect(zonSta.yHigUnoCoo, hotZon.u);
connect(colZon.y, opeModSel.totColZon);
connect(hotZon.y, opeModSel.totHotZon);
connect(opeModSel.yOpeMod, TZonSet.uOpeMod);
connect(opeModSel.yOpeMod, yOpeMod);
connect(TSetRooCooOn.y, TZonSet.TZonCooSetOcc);
connect(TSetRooCooOff.y, TZonSet.TZonCooSetUno);
connect(TSetRooHeaOn.y, TZonSet.TZonHeaSetOcc);
connect(TSetRooHeaOff.y, TZonSet.TZonHeaSetUno);
connect(uWinSta, opeModSel.uWinSta);
end ModeAndSetPoints;