Buildings.HeatTransfer.Windows.BaseClasses

Information

This package contains base classes that are used to construct the models in Buildings.HeatTransfer.Windows.

Extends from Modelica.Icons.BasesPackage (Icon for packages containing base classes).

Package Content

Name	Description
AbsorbedRadiation	Absorbed radiation by window
ExteriorConvectionCoefficient	Model for the heat transfer coefficient at the outside of the window
InteriorConvectionCoefficient	Model for the heat transfer coefficient at the inside of the window
CenterOfGlass	Model for center of glass of a window construction
GasConvection	Model for heat convection through gas in a window assembly
GlassLayer	Model for a glass layer of a window assembly
Overhang	For a window with an overhang, outputs the fraction of the area that is sun exposed
ThermalConductor	Lumped thermal element with variable area, transporting heat without storing it
Shade	Model for infrared radiative heat balance of a layer that may or may not have a shade
ShadeInterface_weatherBus	Base class for models of window shade and overhangs
ShadingSignal	Converts the shading signal to be strictly bigger than 0 and smaller than 1
SideFins	For a window with side fins, outputs the fraction of the area that is sun exposed
PartialConvection	Partial model for heat convection between a possibly shaded window that can be outside or inside the room
PartialRadiation	Partial model for variables and data used in radiation calculation
PartialShade_weatherBus	Partial model to implement overhang and side fins with weather bus connector
TransmittedRadiation	Transmitted radiation through window
WindowRadiation	Calculation radiation for window
RadiationBaseData	Basic parameters for window radiation calculation
RadiationData	Radiation data of a window
convectionVerticalCavity	Free convection in vertical cavity
convectionHorizontalCavity	Free convection in horizontal cavity
nusseltHorizontalCavityEnhanced	Nusselt number for horizontal cavity, bottom surface warmer than top surface
nusseltHorizontalCavityReduced	Nusselt number for horizontal cavity, bottom surface colder than top surface
smoothInterpolation	Get interpolated data without triggering events
Examples	Collection of models that illustrate model use and test models

Buildings.HeatTransfer.Windows.BaseClasses.AbsorbedRadiation

Information

The absorbed radiation by exterior shades includes:

1. the directly absorbed exterior radiation: AWin*uSha*(HDir+HDif)*(1-tau-rho)
2. the indirectly absorbed exterior radiantion from reflection (angular part): AWin*uSha*HDir*tau*rho(IncAng)*(1-tau-rho)
3. the indirectly absorbed of exterior irradiantion from reflection (diffusive part): AWin*uSha*HDif*tau*rho(HEM)*(1-tau-rho)
4. the absorbed interior radiation is neglected.

The absorbed radiation by interior shades includes:

1. the absorbed exterior radiation (angular part): AWin*uSha*HDir*alpha(IncAng)
2. the absorbed exterior radiation (diffusive part): AWin*uSha*HDif*alpha(HEM)
3. the absorbed interior radiation (diffusive part): AWin*uSha*HRoo*(1-tau-rho)

The absorbed radiation by glass includes:

1. the absorbed radiation by unshaded part (diffusive part): AWin*(1-uSha)*(HDif*alphaEx(HEM)+HRoo*alphaIn(HEM))
2. the absorbed radiation by unshaded part (angular part from exterior source): AWin*(1-uSha)*HDir*alphaEx(IncAng)
3. the absorbed radiaiton by shaded part (diffusive part): AWin*uSha*(HDif*alphaExSha(HEM)+HRoo*alphaInSha(HEM))
4. the absorbed radiation by shaded part (angular part from exterior source): AWin*uSha*HDir*alphaExSha(IncAng)

References

• Michael Wetter.
  Simulation-based Building Energy Optimization.
  Dissertation. University of California at Berkeley. 2004.

Extends from Buildings.HeatTransfer.Windows.BaseClasses.PartialRadiation (Partial model for variables and data used in radiation calculation).

Parameters

Type	Name	Default	Description
Boolean	haveExteriorShade		Set to true if window has an exterior shade
Boolean	haveInteriorShade		Set to true if window has an interior shade
Area	AWin		Area of window [m2]
Glass
Integer	N		Number of glass layers
Length	xGla[N]		Thickness of glass [m]
TransmissionCoefficient	tauGlaSol[N]		Solar transmissivity of glass [1]
ReflectionCoefficient	rhoGlaSol_a[N]		Solar reflectivity of glass at surface a (facing outside) [1]
ReflectionCoefficient	rhoGlaSol_b[N]		Solar reflectivity of glass at surface b (facing room-side) [1]
Shade
TransmissionCoefficient	tauShaSol_a		Solar transmissivity of shade for irradiation from air-side [1]
TransmissionCoefficient	tauShaSol_b		Solar transmissivity of shade for irradiation from glass-side [1]
ReflectionCoefficient	rhoShaSol_a		Solar reflectivity of shade for irradiation from air-side [1]
ReflectionCoefficient	rhoShaSol_b		Solar reflectivity of shade for irradiation from glass-side [1]

Connectors

Type	Name	Description
input RealInput	uSha	Control signal for shading (0: unshaded; 1: fully shaded)
input RealInput	HDif	Diffussive solar radiation [W/m2]
input RealInput	incAng	Incident angle [rad]
input RealInput	HDir	Direct solar radiation [W/m2]
input RealInput	HRoo	Diffussive radiation from room [W/m2]
output RealOutput	QAbsExtSha_flow	Absorbed interior and exterior radiation by exterior shading device [W]
output RealOutput	QAbsIntSha_flow	Absorbed interior and exterior radiation by interior shading device [W]
output RealOutput	QAbsGlaUns_flow[N]	Absorbed interior and exterior radiation by unshaded part of glass [W]
output RealOutput	QAbsGlaSha_flow[N]	Absorbed interior and exterior radiation by shaded part of glass [W]

Modelica definition

block AbsorbedRadiation "Absorbed radiation by window"
  extends Buildings.HeatTransfer.Windows.BaseClasses.PartialRadiation;

  Modelica.Blocks.Interfaces.RealInput HRoo(quantity="RadiantEnergyFluenceRate",
      unit="W/m2") "Diffussive radiation from room ";

  Modelica.Blocks.Interfaces.RealOutput QAbsExtSha_flow(final quantity="Power",
      final unit="W") 
    "Absorbed interior and exterior radiation by exterior shading device";
  Modelica.Blocks.Interfaces.RealOutput QAbsIntSha_flow(final quantity="Power",
      final unit="W") 
    "Absorbed interior and exterior radiation by interior shading device";
  Modelica.Blocks.Interfaces.RealOutput QAbsGlaUns_flow[N](each quantity=
        "Power", each final unit="W") 
    "Absorbed interior and exterior radiation by unshaded part of glass";
  Modelica.Blocks.Interfaces.RealOutput QAbsGlaSha_flow[N](each quantity=
        "Power", each final unit="W") 
    "Absorbed interior and exterior radiation by shaded part of glass";

  output Modelica.SIunits.Power absRad[2, N + 2] "Absorbed interior and exterior radiation. 
      (absRad[2,1]: exterior shading device, 
      absRad[1,2 to N+1]: glass (unshaded part),
      absRad[2,2 to N+1]: glass (shaded part),   
      absRad[2,N+2]: interior shading device)";

protected 
  Integer k=1;
  Real x;
  final parameter Integer NDIR=radDat.NDIR;
  final parameter Integer HEM=radDat.HEM;
  constant Integer NoShade=1;
  constant Integer Shade=2;
  constant Integer Interior=1;
  constant Integer Exterior=2;
  final parameter Real coeAbsEx[2, radDat.N, radDat.HEM + 2](fixed=false);
  final parameter Real coeRefExtPan1[radDat.HEM + 2](fixed=false) 
    "Reflectivity of pane 1";
  final parameter Real coeAbsIn[2, radDat.N](fixed=false);
  final parameter Real coeAbsDevExtIrrIntSha[radDat.HEM + 2](fixed=false) 
    "Absorptivity of interior shading device for exterior radiation";
  final parameter Real coeAbsDevExtIrrExtSha=1 - radDat.traRefShaDev[1, 1] -
      radDat.traRefShaDev[2, 1] 
    "Absorptivity of exterior shading device for exterior radiation";
  final parameter Real coeAbsDevIntIrrIntSha=radDat.devAbsIntIrrIntSha 
    "Absorptivity of interior shading device for interior radiation";
  final parameter Real coeAbsDevIntIrrExtSha=1 - radDat.winTraRefIntIrrExtSha[1]
       - radDat.winTraRefIntIrrExtSha[2] 
    "Absorptivity of exterior shading device for interior radiation";
  Real tmpNoSha;
  Real tmpSha;
  Real incAng2;

initial algorithm 
  //**************************************************************
  // Assign coefficients.
  // Data dimension changes from Orginal ([1 : HEM]) to New ([2 : HEM+1])
  // with 2 dummy variable for interpolation.
  //**************************************************************
  // Glass
  for i in 1:N loop
    for j in 1:HEM loop
      // Properties for glass without shading
      coeAbsEx[NoShade, i, j + 1] := radDat.absExtIrrNoSha[i, j];
      coeAbsIn[NoShade, i] := radDat.absIntIrrNoSha[i];
      // Properties for glass with shading
      if haveInteriorShade then
        coeAbsEx[Shade, i, j + 1] := radDat.absExtIrrIntSha[i, j];
        coeAbsIn[Shade, i] := radDat.absIntIrrIntSha[i];
      elseif haveExteriorShade then
        coeAbsEx[Shade, i, j + 1] := radDat.absExtIrrExtSha[i, j];
        coeAbsIn[Shade, i] := radDat.absIntIrrExtSha[i];
      else
        // No Shade
        coeAbsEx[Shade, i, j + 1] := 0.0;
        coeAbsIn[Shade, i] := 0.0;
      end if;
    end for;
    // Dummy variables at 1 and HEM+2
    for k in NoShade:Shade loop
      coeAbsEx[k, i, 1] := coeAbsEx[k, i, 2];
      coeAbsEx[k, i, HEM + 2] := coeAbsEx[k, i, HEM + 1];
    end for;
  end for;

  // Glass Pane 1: Reflectivity
  for j in 1:HEM loop
    coeRefExtPan1[j + 1] := radDat.traRef[2, 1, N, j];
  end for;

  // Interior shades
  for j in 1:HEM loop
    coeAbsDevExtIrrIntSha[j + 1] := radDat.devAbsExtIrrIntShaDev[j];
  end for;

  // Dummy variables at 1 and HEM+2
  coeRefExtPan1[1] := coeRefExtPan1[2];
  coeRefExtPan1[HEM + 2] := coeRefExtPan1[HEM + 1];
  coeAbsDevExtIrrIntSha[1] := coeAbsDevExtIrrIntSha[2];
  coeAbsDevExtIrrIntSha[HEM + 2] := coeAbsDevExtIrrIntSha[HEM + 1];

algorithm 
  absRad[NoShade, 1] := 0.0;
  absRad[NoShade, N + 2] := 0.0;
  absRad[Shade, 1] := 0.0;
  absRad[Shade, N + 2] := 0.0;

  //**************************************************************
  // Glass: absorbed diffusive radiation from exterior and interior sources
  //**************************************************************
  for i in 1:N loop
    absRad[NoShade, i + 1] := AWin*(1 - uSha_internal)*(HDif*coeAbsEx[NoShade,
      i, HEM + 1] + HRoo*coeAbsIn[NoShade, i]);
    absRad[Shade, i + 1] := AWin*uSha_internal*(HDif*coeAbsEx[Shade, i, HEM + 1]
       + HRoo*coeAbsIn[Shade, i]);
  end for;

  //**************************************************************
  // Shading device: absorbed radiation from exterior source
  //**************************************************************
  // Exterior Shading Device:
  // direct radiation: 1. direct absorption;
  // diffusive radiation: 1. direct absorption 2. absorption from back reflection
  if haveExteriorShade then
    absRad[Shade, 1] := AWin*uSha_internal*coeAbsDevExtIrrExtSha*(HDif + HDir
       + HDif*radDat.traRefShaDev[1, 1]*radDat.traRef[2, 1, N, HEM]);
    // Interior Shading Device: diffusive radiation from both interior and exterior
  elseif haveInteriorShade then
    absRad[Shade, N + 2] := AWin*uSha_internal*(HDif*radDat.devAbsExtIrrIntShaDev[
      HEM] + HRoo*coeAbsDevIntIrrIntSha);
  end if;

  //**************************************************************
  // Glass, Device: add absorbed direct radiation from exterior sources
  //**************************************************************
  // Use min() instead of if() to avoid event
  incAng2 := min(incAng, 0.5*Modelica.Constants.pi);

  x := 2*(NDIR - 1)*abs(incAng2)/Modelica.Constants.pi 
    "x=(index-1)*incAng/(0.5pi), 0<=x<=NDIR";
  x := x + 2;

  for i in 1:N loop
    // Glass without shading: Add absorbed direct radiation
    tmpNoSha :=
      Buildings.HeatTransfer.Windows.BaseClasses.smoothInterpolation({
      coeAbsEx[NoShade, i, k] for k in 1:(HEM + 2)}, x);
    absRad[NoShade, i + 1] := absRad[NoShade, i + 1] + AWin*HDir*(1 -
      uSha_internal)*tmpNoSha;

    // Glass with shading: add absorbed direct radiation
    tmpSha :=
      Buildings.HeatTransfer.Windows.BaseClasses.smoothInterpolation({
      coeAbsEx[Shade, i, k] for k in 1:(HEM + 2)}, x);
    absRad[Shade, i + 1] := absRad[Shade, i + 1] + AWin*HDir*uSha_internal*
      tmpSha;
  end for;

  // Interior shading device: add absorbed direct radiation
  if haveInteriorShade then
    tmpSha :=
      Buildings.HeatTransfer.Windows.BaseClasses.smoothInterpolation({
      coeAbsDevExtIrrIntSha[k] for k in 1:(HEM + 2)}, x);
    absRad[Shade, N + 2] := absRad[Shade, N + 2] + AWin*HDir*uSha_internal*
      tmpSha;
  end if;

  // Exterior shading device: add absorbed reflection of direct radiation from exterior source
  if haveExteriorShade then
    tmpNoSha :=
      Buildings.HeatTransfer.Windows.BaseClasses.smoothInterpolation({
      coeRefExtPan1[k] for k in 1:(HEM + 2)}, x);
    absRad[Shade, 1] := absRad[Shade, 1] + AWin*HDir*uSha_internal*
      coeAbsDevExtIrrExtSha*tmpNoSha;
  end if;

  // Assign quantities to output connectors
  QAbsExtSha_flow := absRad[2, 1];
  QAbsIntSha_flow := absRad[2, N + 2];
  QAbsGlaUns_flow[:] := absRad[1, 2:N + 1];
  QAbsGlaSha_flow[:] := absRad[2, 2:N + 1];
end AbsorbedRadiation;

Buildings.HeatTransfer.Windows.BaseClasses.ExteriorConvectionCoefficient

Information

h = 4+4 v

References

TARCOG 2006: Carli, Inc., TARCOG: Mathematical models for calculation of thermal performance of glazing systems with our without shading devices, Technical Report, Oct. 17, 2006.

Extends from Modelica.Blocks.Interfaces.BlockIcon (Basic graphical layout of input/output block).

Parameters

Type	Name	Default	Description
Area	A		Heat transfer area [m2]

Connectors

Type	Name	Description
output RealOutput	GCon	Convective thermal conductance [W/K]
input RealInput	v	Wind speed [m/s]

Modelica definition

model ExteriorConvectionCoefficient 
  "Model for the heat transfer coefficient at the outside of the window"
  extends Modelica.Blocks.Interfaces.BlockIcon;
  parameter Modelica.SIunits.Area A "Heat transfer area";

  Modelica.Blocks.Interfaces.RealOutput GCon(unit="W/K") 
    "Convective thermal conductance";
  Modelica.Blocks.Interfaces.RealInput v(unit="m/s") "Wind speed";

equation 
  GCon = A*(4+4*Buildings.Utilities.Math.Functions.smoothMax(v, -v, 0.1));
end ExteriorConvectionCoefficient;

Buildings.HeatTransfer.Windows.BaseClasses.InteriorConvectionCoefficient

Information

h = 4 W ⁄ (m² K).

References

TARCOG 2006: Carli, Inc., TARCOG: Mathematical models for calculation of thermal performance of glazing systems with our without shading devices, Technical Report, Oct. 17, 2006.

Extends from Modelica.Blocks.Interfaces.BlockIcon (Basic graphical layout of input/output block).

Parameters

Type	Name	Default	Description
Area	A		Heat transfer area [m2]

Connectors

Type	Name	Description
output RealOutput	GCon	Convective thermal conductance [W/K]

Modelica definition

model InteriorConvectionCoefficient 
  "Model for the heat transfer coefficient at the inside of the window"
  extends Modelica.Blocks.Interfaces.BlockIcon;
  parameter Modelica.SIunits.Area A "Heat transfer area";

  Modelica.Blocks.Interfaces.RealOutput GCon(unit="W/K") 
    "Convective thermal conductance";

equation 
  GCon = 4*A;
end InteriorConvectionCoefficient;

Buildings.HeatTransfer.Windows.BaseClasses.CenterOfGlass

Information

• the models extSha and intSha for the heat balance of the shade, modeled using Buildings.HeatTransfer.Windows.BaseClasses.Shade.
• an array of models glass for the heat conduction and the infrared radiative heat balance of the glass layers. There can be an arbitrary number of glass layers, which are all modeled using instances of Buildings.HeatTransfer.Windows.BaseClasses.GlassLayer.
• an array of models gas for the gas layers. There is one model of a gas layer between each window panes. The gas layers are modeled using instances of Buildings.HeatTransfer.Windows.BaseClasses.GasConvection.

Extends from Buildings.HeatTransfer.Radiosity.BaseClasses.RadiosityTwoSurfaces (Model for the radiosity balance of a device with two surfaces).

Parameters

Type	Name	Default	Description
Area	A		Surface area [m2]
Angle	til		Surface tilt (only 90 degrees=vertical is implemented) [rad]
Generic	glaSys		Glazing system
Boolean	linearize	false	Set to true to linearize emissive power

Connectors

Type	Name	Description
input RadiosityInflow	JIn_a	Incoming radiosity at surface a [W]
input RadiosityInflow	JIn_b	Incoming radiosity at surface b [W]
output RadiosityOutflow	JOut_a	Outgoing radiosity at surface a [W]
output RadiosityOutflow	JOut_b	Outgoing radiosity at surface b [W]
input RealInput	u	Input connector, used to scale the surface area to take into account an operable shading device
HeatPort_a	glass_a	Heat port connected to the outside facing surface of the glass
HeatPort_b	glass_b	Heat port connected to the room-facing surface of the glass
input RealInput	QAbs_flow[size(glass, 1)]	Solar radiation absorbed by glass [W]

Modelica definition

model CenterOfGlass 
  "Model for center of glass of a window construction"
  extends Buildings.HeatTransfer.Radiosity.BaseClasses.RadiosityTwoSurfaces;
  parameter Modelica.SIunits.Area A "Heat transfer area";
  parameter Modelica.SIunits.Angle til(displayUnit="deg") 
    "Surface tilt (only 90 degrees=vertical is implemented)";

  parameter Buildings.HeatTransfer.Data.GlazingSystems.Generic glaSys 
    "Glazing system";

  Modelica.Blocks.Interfaces.RealInput u 
    "Input connector, used to scale the surface area to take into account an operable shading device";
    

  Buildings.HeatTransfer.Windows.BaseClasses.GlassLayer[glaSys.nLay] glass(
    each final A=A,
    final x=glaSys.glass.x,
    final k=glaSys.glass.k,
    final absIR_a=glaSys.glass.absIR_a,
    final absIR_b=glaSys.glass.absIR_b,
    final tauIR=glaSys.glass.tauIR,
    each final linearize=linearize) "Window glass layer";
  Buildings.HeatTransfer.Windows.BaseClasses.GasConvection gas[glaSys.nLay-1](
    each final A=A,
    final gas=glaSys.gas,
    each final til=til,
    each linearize=linearize) "Window gas layer";

  // Note that the interior shade is flipped horizontally. Hence, surfaces a and b are exchanged,
  // i.e., surface a faces the room, while surface b faces the window

  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_a glass_a 
    "Heat port connected to the outside facing surface of the glass";
  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_b glass_b 
    "Heat port connected to the room-facing surface of the glass";

  parameter Boolean linearize=false "Set to true to linearize emissive power";
  Modelica.Blocks.Interfaces.RealInput QAbs_flow[size(glass, 1)](each unit="W", each 
      quantity =                                                                              "Power") 
    "Solar radiation absorbed by glass";
equation 
  for i in 1:glaSys.nLay-1 loop
    connect(glass[i].port_b, gas[i].port_a);
    connect(gas[i].port_b, glass[i+1].port_a);

    connect(glass[i].JOut_b, glass[i+1].JIn_a);
    connect(glass[i].JIn_b, glass[i+1].JOut_a);

    connect(u, gas[i].u);

  end for;

  for i in 1:glaSys.nLay loop
    connect(u, glass[i].u);
  end for;

  connect(glass_b, glass[glaSys.nLay].port_b);

  connect(glass_a, glass[1].port_a);

  connect(JIn_a, glass[1].JIn_a);
  connect(glass[1].JOut_a, JOut_a);
  connect(glass[glaSys.nLay].JOut_b, JOut_b);
  connect(JIn_b, glass[glaSys.nLay].JIn_b);
  connect(glass.QAbs_flow, QAbs_flow);
end CenterOfGlass;

Buildings.HeatTransfer.Windows.BaseClasses.GasConvection

Information

To use this model, set the parameter til to a value defined in Buildings.HeatTransfer.Types.Tilt.

If the parameter linearize is set to true, then all equations are linearized.

References

TARCOG 2006: Carli, Inc., TARCOG: Mathematical models for calculation of thermal performance of glazing systems with our without shading devices, Technical Report, Oct. 17, 2006.

Extends from Modelica.Thermal.HeatTransfer.Interfaces.Element1D (Partial heat transfer element with two HeatPort connectors that does not store energy), Buildings.BaseClasses.BaseIcon (Base icon).

Parameters

Type	Name	Default	Description
Generic	gas		Thermophysical properties of gas fill
Area	A		Heat transfer area [m2]
Area	h	sqrt(A)	Height of window [m2]
Angle	til		Surface tilt (only 0, 90 and 180 degrees are implemented) [rad]
Boolean	linearize	false	Set to true to linearize emissive power
Temperature	T0	293.15	Temperature used to compute thermophysical properties [K]

Connectors

Type	Name	Description
input RealInput	u	Input connector, used to scale the surface area to take into account an operable shading device

Modelica definition

model GasConvection 
  "Model for heat convection through gas in a window assembly"
  extends Modelica.Thermal.HeatTransfer.Interfaces.Element1D(
     port_a(T(start=293.15)),
     port_b(T(start=293.15)));
  extends Buildings.BaseClasses.BaseIcon;
  parameter Buildings.HeatTransfer.Data.Gases.Generic gas 
    "Thermophysical properties of gas fill";
  parameter Modelica.SIunits.Area A "Heat transfer area";
  parameter Modelica.SIunits.Area h(min=0) = sqrt(A) "Height of window";

  parameter Modelica.SIunits.Angle til(displayUnit="deg") 
    "Surface tilt (only 0, 90 and 180 degrees are implemented)";
  parameter Boolean linearize=false "Set to true to linearize emissive power";

  Modelica.Blocks.Interfaces.RealInput u 
    "Input connector, used to scale the surface area to take into account an operable shading device";
    

  parameter Modelica.SIunits.Temperature T0 = 293.15 
    "Temperature used to compute thermophysical properties";
  Modelica.SIunits.CoefficientOfHeatTransfer hCon(min=0, start=3) 
    "Convective heat transfer coefficient";
  Modelica.SIunits.HeatFlux q_flow "Convective heat flux";
  Real Nu(min=0) "Nusselt number";
  Real Ra(min=0) "Raleigh number";
protected 
  Modelica.SIunits.Temperature T_a 
    "Temperature used for thermophysical properties at port_a";
  Modelica.SIunits.Temperature T_b 
    "Temperature used for thermophysical properties at port_b";
  Modelica.SIunits.Temperature T_m 
    "Temperature used for thermophysical properties";

  Real deltaNu(min=0.01) = 0.1 
    "Small value for Nusselt number, used for smoothing";
  Real deltaRa(min=0.01) = 100 
    "Small value for Raleigh number, used for smoothing";
  final parameter Real cosTil=Modelica.Math.cos(til) "Cosine of window tilt";
  final parameter Real sinTil=Modelica.Math.sin(til) "Sine of window tilt";
  final parameter Boolean isVertical = abs(cosTil) < 10E-10 
    "Flag, true if the window is in a wall";
  final parameter Boolean isHorizontal = abs(sinTil) < 10E-10 
    "Flag, true if the window is horizontal";
  // Quantities that are only used in linearized model

  parameter Modelica.SIunits.CoefficientOfHeatTransfer hCon0(fixed=false) 
    "Convective heat transfer coefficient";
  parameter Real Nu0(fixed=false, min=0) "Nusselt number";
  parameter Real Ra0(fixed=false, min=0) "Raleigh number";
  parameter Boolean homotopyInitialization = true "= true, use homotopy method";

initial equation 
  assert(isVertical or isHorizontal, "Only vertical and horizontal windows are implemented.");
initial equation 
  // Computations that are used in the linearized model only
  Ra0 = Buildings.HeatTransfer.Convection.Functions.HeatFlux.raleigh(
    x=gas.x,
    rho=Buildings.HeatTransfer.Data.Gases.density(gas, T0),
    c_p=Buildings.HeatTransfer.Data.Gases.specificHeatCapacity(gas, T0),
    mu=Buildings.HeatTransfer.Data.Gases.dynamicViscosity(gas, T0),
    k=Buildings.HeatTransfer.Data.Gases.thermalConductivity(gas, T0),
    T_a=T0-5,
    T_b=T0+5,
    Ra_min=100);
  (Nu0, hCon0) = Buildings.HeatTransfer.Windows.BaseClasses.convectionVerticalCavity(
            gas=gas, Ra=Ra0, T_m=T0, dT=10, h=h, deltaNu=deltaNu, deltaRa=deltaRa);

equation 
  T_a = port_a.T;
  T_b = port_b.T;
  T_m = (port_a.T+port_b.T)/2;
  if linearize then
    Ra=Ra0;
    Nu=Nu0;
    hCon=hCon0;
    q_flow = hCon0 * dT;
  else
    Ra = Buildings.HeatTransfer.Convection.Functions.HeatFlux.raleigh(
      x=gas.x,
      rho=Buildings.HeatTransfer.Data.Gases.density(gas, T_m),
      c_p=Buildings.HeatTransfer.Data.Gases.specificHeatCapacity(gas, T_m),
      mu=Buildings.HeatTransfer.Data.Gases.dynamicViscosity(gas, T_m),
      k=Buildings.HeatTransfer.Data.Gases.thermalConductivity(gas, T_m),
      T_a=T_a,
      T_b=T_b,
      Ra_min=100);
    if isVertical then
       (Nu, hCon, q_flow) = Buildings.HeatTransfer.Windows.BaseClasses.convectionVerticalCavity(
              gas=gas, Ra=Ra, T_m=T_m, dT=dT, h=h, deltaNu=deltaNu, deltaRa=deltaRa);
    elseif isHorizontal then
       (Nu, hCon, q_flow) = Buildings.HeatTransfer.Windows.BaseClasses.convectionHorizontalCavity(
              gas=gas, Ra=Ra, T_m=T_m, dT=dT, til=til, sinTil=sinTil, cosTil=cosTil,
              h=h, deltaNu=deltaNu, deltaRa=deltaRa);

    else
       Nu = 0;
       hCon=0;
       q_flow=0;
    end if; // isVertical or isHorizontal
  end if; // linearize
  if homotopyInitialization then
    Q_flow = u*A*homotopy(actual=q_flow,
                          simplified=hCon0*dT);
  else
    Q_flow = u*A*q_flow;
  end if;
end GasConvection;

Buildings.HeatTransfer.Windows.BaseClasses.GlassLayer

Information

Extends from Buildings.HeatTransfer.Radiosity.BaseClasses.RadiosityTwoSurfaces (Model for the radiosity balance of a device with two surfaces), Buildings.HeatTransfer.Radiosity.BaseClasses.ParametersTwoSurfaces (Parameters that are used to model two surfaces with the same area).

Parameters

Type	Name	Default	Description
Area	A		Surface area [m2]
Emissivity	absIR_a		Infrared absorptivity of surface a [1]
Emissivity	absIR_b		Infrared absorptivity of surface b [1]
ReflectionCoefficient	rhoIR_a	1 - absIR_a - tauIR	Infrared reflectivity of surface a [1]
ReflectionCoefficient	rhoIR_b	1 - absIR_b - tauIR	Infrared reflectivity of surface b [1]
TransmissionCoefficient	tauIR		Infrared transmissivity of glass pane [1]
Boolean	linearize	false	Set to true to linearize emissive power
Temperature	T0	293.15	Temperature used to linearize radiative heat transfer [K]
Length	x		Material thickness [m]
ThermalConductivity	k		Thermal conductivity [W/(m.K)]
Advanced
Boolean	homotopyInitialization	true	= true, use homotopy method

Connectors

Type	Name	Description
input RadiosityInflow	JIn_a	Incoming radiosity at surface a [W]
input RadiosityInflow	JIn_b	Incoming radiosity at surface b [W]
output RadiosityOutflow	JOut_a	Outgoing radiosity at surface a [W]
output RadiosityOutflow	JOut_b	Outgoing radiosity at surface b [W]
input RealInput	u	Input connector, used to scale the surface area to take into account an operable shading device
HeatPort_a	port_a	Heat port at surface a
HeatPort_b	port_b	Heat port at surface b
input RealInput	QAbs_flow	Solar radiation absorbed by glass [W]

Modelica definition

model GlassLayer "Model for a glass layer of a window assembly"
  extends Buildings.HeatTransfer.Radiosity.BaseClasses.RadiosityTwoSurfaces;
  extends Buildings.HeatTransfer.Radiosity.BaseClasses.ParametersTwoSurfaces(
    final rhoIR_a=1-absIR_a-tauIR,
    final rhoIR_b=1-absIR_b-tauIR);
  parameter Modelica.SIunits.Length x "Material thickness";
  parameter Modelica.SIunits.ThermalConductivity k "Thermal conductivity";
  parameter Modelica.SIunits.Area A "Heat transfer area";
  parameter Modelica.SIunits.Emissivity absIR_a 
    "Infrared absorptivity of surface a (usually room-facing surface)";
  parameter Modelica.SIunits.Emissivity absIR_b 
    "Infrared absorptivity of surface b (usually outside-facing surface)";
  parameter Modelica.SIunits.Emissivity tauIR "Infrared transmittance of glass";

  Modelica.Blocks.Interfaces.RealInput u 
    "Input connector, used to scale the surface area to take into account an operable shading device";
  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_a port_a(T(start=293.15, nominal=293.15)) 
    "Heat port at surface a";
  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_b port_b(T(start=293.15, nominal=293.15)) 
    "Heat port at surface b";
  Modelica.Blocks.Interfaces.RealInput QAbs_flow(unit="W", quantity="Power") 
    "Solar radiation absorbed by glass";
  parameter Boolean linearize=false "Set to true to linearize emissive power";
  parameter Boolean homotopyInitialization = true "= true, use homotopy method";
protected 
 Real T4_a(min=1E8, unit="K4", start=293.15^4, nominal=1E10) 
    "4th power of temperature at surface a";
 Real T4_b(min=1E8, unit="K4", start=293.15^4, nominal=1E10) 
    "4th power of temperature at surface b";
 Modelica.SIunits.HeatFlowRate E_a(min=0, nominal=1E2) 
    "Emissive power of surface a";
 Modelica.SIunits.HeatFlowRate E_b(min=0, nominal=1E2) 
    "Emissive power of surface b";
 final parameter Modelica.SIunits.ThermalResistance R = x/2/k/A 
    "Thermal resistance from surface of glass to center of glass";
equation 
  // Heat balance of surface node
  // These equations are from Window 6 Technical report, (2.1-14) to (2.1-17)
  0 = port_a.Q_flow + port_b.Q_flow + QAbs_flow + JIn_a  + JIn_b + JOut_a + JOut_b;
  //port_b.T-port_a.T = R/u * (2*port_b.Q_flow+QAbs_flow);
  //   u * (port_b.T-port_a.T) = 2*R * (-port_a.Q_flow-QAbs_flow/2-(absIR_a*JIn_a-E_a));
  u * (port_b.T-port_a.T) = 2*R * (-port_a.Q_flow-QAbs_flow/2-JIn_a-JOut_a); // Ticket 56
  // Radiosity balance
  if linearize then
    T4_a = 4*T03*port_a.T - 3*T04;
    T4_b = 4*T03*port_b.T - 3*T04;
  else
    if homotopyInitialization then
      T4_a = homotopy(actual=port_a.T^4, simplified=4*T03*port_a.T - 3*T04);
      T4_b = homotopy(actual=port_b.T^4, simplified=4*T03*port_b.T - 3*T04);
    else
      T4_a = port_a.T^4;
      T4_b = port_b.T^4;
    end if;
  end if;
  // Emissive power
  E_a = u * A * absIR_a * Modelica.Constants.sigma * T4_a;
  E_b = u * A * absIR_b * Modelica.Constants.sigma * T4_b;
  // Radiosities that are outgoing from the surface, which are
  // equal to the infrared absorptivity plus the reflected incoming
  // radiosity plus the radiosity that is transmitted from the
  // other surface.
  -JOut_a = E_a + rhoIR_a * JIn_a + tauIR * JIn_b;
  -JOut_b = E_b + rhoIR_b * JIn_b + tauIR * JIn_a;
end GlassLayer;

Buildings.HeatTransfer.Windows.BaseClasses.Overhang

Information

For a window with an overhang, this block outputs the fraction of the area that is exposed to the sun. This models can also be used for doors with an overhang.

Input to this block are the wall solar azimuth angle and the altitude angle of the sun. These angles can be calculated using blocks from the package Buildings.BoundaryConditions.SolarGeometry.BaseClasses.

The overhang can be asymmetrical (i.e. wR ≠ wL) about the vertical centerline of the window. The overhang must completely cover the window (i.e., wL ≥ 0 and wR ≥ 0). wL and wR are measured from the left and right edge of the window.

The surface azimuth azi is as defined in Buildings.HeatTransfer.Types.Azimuth.

Implementation

The method of super position is used to calculate the window shaded area. The area below the overhang is divided as shown in the figure.

Dimensional variables used in code for the rectangle DEGI, AEGH, CFGI and BFGH are shown in the figure below:

The rectangles DEGI, AEGH, CFGI and BFGH have the same geometric configuration with respect to the overhang. Thus, the same algorithm can be used to calculate the shaded portion in these areas. A single equation in the for loop improves the total calculation time, as compared to if-then-else conditions, considering the various shapes of the shaded portions. To find the shaded area in window ABCD, the shaded portion of AEGD and CFGI should be subtracted from that of DEGI and BFGH. This shaded area of the window is then divided by the total window area to calculate the shaded fraction of the window.

Extends from Modelica.Blocks.Interfaces.BlockIcon (Basic graphical layout of input/output block), Buildings.Rooms.BaseClasses.Overhang (Record for window overhang).

Parameters

Type	Name	Default	Description
Angle	lat		Latitude [rad]
Angle	azi		Surface azimuth; azi= -90 degree East; azi= 0 degree South [rad]
Overhang
Length	wL		Overhang width left to the window, measured from the window corner [m]
Length	wR		Overhang width right to the window, measured from the window corner [m]
Length	dep		Overhang depth (measured perpendicular to the wall plane) [m]
Length	gap		Distance between window upper edge and overhang lower edge [m]
Window
Length	hWin		Window height [m]
Length	wWin		Window width [m]

Connectors

Type	Name	Description
input RealInput	verAzi	Wall solar azimuth angle (angle between projection of sun's rays and normal to vertical surface) [rad]
input RealInput	alt	Altitude angle [rad]
output RealOutput	fraSun	Fraction of window area exposed to the sun [1]
Bus	weaBus

Modelica definition

block Overhang 
  "For a window with an overhang, outputs the fraction of the area that is sun exposed"
  extends Modelica.Blocks.Interfaces.BlockIcon;
  extends Buildings.Rooms.BaseClasses.Overhang;

  Modelica.Blocks.Interfaces.RealInput verAzi(quantity="Angle", unit="rad", displayUnit="deg") 
    "Wall solar azimuth angle (angle between projection of sun's rays and normal to vertical surface)";
    

   Modelica.Blocks.Interfaces.RealInput alt(
     quantity="Angle",
     unit="rad",
     displayUnit="deg") "Altitude angle";

  Modelica.Blocks.Interfaces.RealOutput fraSun(final min=0,
                                               final max=1,
                                               final unit="1") 
    "Fraction of window area exposed to the sun";
  parameter Modelica.SIunits.Angle lat "Latitude";

  parameter Modelica.SIunits.Angle azi(displayUnit="deg") 
    "Surface azimuth; azi= -90 degree East; azi= 0 degree South";

// Window dimensions
  parameter Modelica.SIunits.Length hWin "Window height";
  parameter Modelica.SIunits.Length wWin "Window width";

  Buildings.BoundaryConditions.WeatherData.Bus weaBus;

protected 
  constant Modelica.SIunits.Angle delSolAzi = 0.005 
    "Half-width of transition interval between left and right formulation for overhang";

  final parameter Modelica.SIunits.Area AWin= hWin*wWin "Window area";
  parameter Modelica.SIunits.Length tmpH[4](fixed=false) 
    "Height rectangular sections used for superposition";
  Modelica.SIunits.Length w 
    "Either wL or wR, depending on the sun relative to the wall azimuth";
  Modelica.SIunits.Length tmpW[4] 
    "Width of rectangular sections used for superpositions";
  Modelica.SIunits.Length del_L = wWin/100 
    "Fraction of window dimension over which min-max functions are smoothened";
  Modelica.SIunits.Length x1 
    "Horizontal distance between window side edge and shadow corner";
  Modelica.SIunits.Length x2[4] 
    "Horizontal distance between window side edge and point where shadow line and window lower edge intersects";
  Modelica.SIunits.Length y1 
    "Vertical distance between overhang and shadow lower edge";
  Modelica.SIunits.Length y2[4] 
    "Window height (vertical distance corresponding to x2)";
  Real shdwTrnglRtio "ratio of y1 and x1";
  Modelica.SIunits.Area area[4] 
    "Shaded areas of the sections used in superposition";
  Modelica.SIunits.Area shdArea "Shaded area calculated from equations";
  Modelica.SIunits.Area crShdArea "Final value for shaded area";
  Modelica.SIunits.Area crShdArea1 
    "Corrected for the sun behind the surface/wall";
  Modelica.SIunits.Area crShdArea2 "Corrected for the sun below horizon";

  Buildings.BoundaryConditions.SolarGeometry.BaseClasses.SolarAzimuth solAzi(lat=lat) 
    "Solar azimuth";

initial algorithm 
  assert(wL >= 0,  "Overhang must cover complete window
    Received overhang width on left hand side, wL = " + String(wL));
  assert(wR >= 0,  "Overhang must cover complete window
    Received overhang width on right hand side, wR = " + String(wR));

  for i in 1:4 loop
    tmpH[i] := gap + mod((i - 1), 2)*hWin;
  end for;

equation 
  // if dep=0, then the equation
  //   y1*Modelica.Math.cos(verAzi) = dep*Modelica.Math.tan(alt);
  // is singular. Hence, we treat this special case with an
  // if-then construct.
  // This also increases computing efficiency in
  // Buildings.HeatTransfer.Windows.FixedShade in case the window has no overhang.

  if haveOverhang then
    //Temporary height and widths are for the areas below the overhang
    //These areas are used in superposition
    w = Buildings.Utilities.Math.Functions.spliceFunction(
            pos=wL,
            neg=wR,
            x=solAzi.solAzi-azi,
            deltax=delSolAzi);
    tmpW[1] = w + wWin;
    tmpW[2] = w;
    tmpW[3] = w;
    tmpW[4] = w + wWin;

    y1*Modelica.Math.cos(verAzi) = dep*Modelica.Math.tan(alt);
    x1 = dep*Modelica.Math.tan(verAzi);
    shdwTrnglRtio*x1 = y1;
    for i in 1:4 loop
      y2[i] = tmpH[i];
      x2[i]*y1 = x1*tmpH[i];
      area[i] = Buildings.Utilities.Math.Functions.smoothMin(
        x1=y1,
        x2=y2[i],
          deltaX=del_L)*tmpW[i] - (Buildings.Utilities.Math.Functions.smoothMin(
        y1,
        tmpH[i],
        del_L)*Buildings.Utilities.Math.Functions.smoothMin(
        x1=x2[i],
        x2=y1,
        deltaX=del_L)/2) + Buildings.Utilities.Math.Functions.smoothMax(
        x1=shdwTrnglRtio*(Buildings.Utilities.Math.Functions.smoothMin(
          x1=x1,
          x2=x2[i],
          deltaX=del_L) - tmpW[i]),
        x2=0,
        deltaX=del_L)*Buildings.Utilities.Math.Functions.smoothMax(
        x1=(Buildings.Utilities.Math.Functions.smoothMin(
          x1=x1,
          x2=x2[i],
          deltaX=del_L) - tmpW[i]),
        x2=0,
        deltaX=del_L)/2;
    end for;
    shdArea = area[4] + area[3] - area[2] - area[1];
  // correction case: Sun not in front of the wall
    crShdArea1 = Buildings.Utilities.Math.Functions.spliceFunction(
      pos=shdArea,
      neg=AWin,
      x=(Modelica.Constants.pi/2)-verAzi,
      deltax=0.01);
  // correction case: Sun not above horizon
    crShdArea2 = Buildings.Utilities.Math.Functions.spliceFunction(
      pos=shdArea,
      neg=AWin,
      x=alt,
      deltax=0.01);
    crShdArea=Buildings.Utilities.Math.Functions.smoothMax(x1=crShdArea1,
                                                           x2=crShdArea2,
                                                           deltaX=0.01);
    fraSun = Buildings.Utilities.Math.Functions.smoothMin(
        x1=Buildings.Utilities.Math.Functions.smoothMax(x1=1-crShdArea/AWin,x2=0,deltaX=0.01),
        x2=1.0,
        deltaX=0.01);
  else
    w = 0;
    tmpW=fill(0.0, 4);
    y1 = 0;
    x1 = 0;
    shdwTrnglRtio = 0;
    for i in 1:4 loop
      y2[i] = 0;
      x2[i] = 0;
      area[i] = 0;
    end for;
    shdArea = 0;
    crShdArea1 = 0;
    crShdArea2 = 0;
    crShdArea  = 0;
    fraSun     = 0;
   end if;

  connect(weaBus.solTim, solAzi.solTim);
  connect(weaBus.sol.zen, solAzi.zen);
  connect(weaBus.sol.dec, solAzi.decAng);

end Overhang;

Buildings.HeatTransfer.Windows.BaseClasses.ThermalConductor

Information

This is a model for transport of heat without storing it. It is identical to the thermal conductor from the Modelica Standard Library, except that it adds an input signal u.

Extends from Modelica.Thermal.HeatTransfer.Interfaces.Element1D (Partial heat transfer element with two HeatPort connectors that does not store energy), Buildings.BaseClasses.BaseIconLow (Base icon with model name below the icon).

Parameters

Type	Name	Default	Description
ThermalConductance	G		Constant thermal conductance of material [W/K]

Connectors

Type	Name	Description
HeatPort_a	port_a
HeatPort_b	port_b
input RealInput	u	Input signal for thermal conductance

Modelica definition

model ThermalConductor 
  "Lumped thermal element with variable area, transporting heat without storing it"
  extends Modelica.Thermal.HeatTransfer.Interfaces.Element1D;
  extends Buildings.BaseClasses.BaseIconLow;
  parameter Modelica.SIunits.ThermalConductance G 
    "Constant thermal conductance of material";
  Modelica.Blocks.Interfaces.RealInput u(min=0) 
    "Input signal for thermal conductance";
equation 
  Q_flow = u*G*dT;
end ThermalConductor;

Buildings.HeatTransfer.Windows.BaseClasses.Shade

Information

Model for the convective and the infrared radiative heat balance of a shade that is in the outside or the room-side of a window.

The input port QAbs_flow needs to be connected to the solar radiation that is absorbed by the shade.

The convective heat balance is based on the model described by Wright (2008), which can be shown as a convective heat resistance model as follows:

Wright (2008) reports that if the shading layer is far enough from the window, the boundary layers associated with each surface will not interfere with each other. In this case, it is reasonable to consider each surface on an individual basis by setting the convective heat transfer coefficient shown in grey to zero, and setting the black depicted convective heat transfer coefficients to h=4 W/m² K. In the here implemented model, the grey depicted convective heat transfer coefficient is set set to h' = k   h, where 0 ≤ k ≤ 1 is a parameter.

References

• Jon L. Wright.
  Calculating Center-Glass Performance Indices of Glazing Systems with Shading Devices.
  ASHRAE Transactions, SL-08-020. 2008.

Parameters

Type	Name	Default	Description
Area	A		Heat transfer area [m2]
Emissivity	absIR_air		Infrared absorptivity of surface that faces air [1]
Emissivity	absIR_glass		Infrared absorptivity of surface that faces glass [1]
TransmissionCoefficient	tauIR_air		Infrared transmissivity of shade for radiation coming from the exterior or the room [1]
TransmissionCoefficient	tauIR_glass		Infrared transmissivity of shade for radiation coming from the glass [1]
Boolean	thisSideHasShade		Set to true if this side of the window has a shade
Boolean	linearize	false	Set to true to linearize emissive power
Temperature	T0	293.15	Temperature used to linearize radiative heat transfer [K]
Real	k	1	Coefficient used to scale convection between shade and glass
Advanced
Boolean	homotopyInitialization	true	= true, use homotopy method

Connectors

Type	Name	Description
input RealInput	u	Input connector, used to scale the surface area to take into account an operable shading device
input RealInput	Gc	Signal representing the convective thermal conductance in [W/K]
input RealInput	QAbs_flow	Solar radiation absorbed by shade [W]
input RadiosityInflow	JIn_air	Incoming radiosity at the air-side surface of the shade [W]
input RadiosityInflow	JIn_glass	Incoming radiosity at the glass-side surface of the shade [W]
output RadiosityOutflow	JOut_air	Outgoing radiosity at the air-side surface of the shade [W]
output RadiosityOutflow	JOut_glass	Outgoing radiosity at the glass-side surface of the shade [W]
HeatPort_a	air	Port that connects to the air (room or outside)
HeatPort_b	glass	Heat port that connects to shaded part of glass
HeatPort_a	sha	Heat port to shade

Modelica definition

model Shade 
  "Model for infrared radiative heat balance of a layer that may or may not have a shade"

  parameter Modelica.SIunits.Area A "Heat transfer area";
  parameter Modelica.SIunits.Emissivity absIR_air 
    "Infrared absorptivity of surface that faces air";
  parameter Modelica.SIunits.Emissivity absIR_glass 
    "Infrared absorptivity of surface that faces glass";
  parameter Modelica.SIunits.TransmissionCoefficient tauIR_air 
    "Infrared transmissivity of shade for radiation coming from the exterior or the room";
  parameter Modelica.SIunits.TransmissionCoefficient tauIR_glass 
    "Infrared transmissivity of shade for radiation coming from the glass";
  parameter Boolean thisSideHasShade 
    "Set to true if this side of the window has a shade";
  final parameter Modelica.SIunits.ReflectionCoefficient rhoIR_air=1-absIR_air-tauIR_air 
    "Infrared reflectivity of surface that faces air";
  final parameter Modelica.SIunits.ReflectionCoefficient rhoIR_glass=1-absIR_glass-tauIR_glass 
    "Infrared reflectivity of surface that faces glass";
  parameter Boolean linearize = false "Set to true to linearize emissive power";
  parameter Boolean homotopyInitialization = true "= true, use homotopy method";

  parameter Modelica.SIunits.Temperature T0=293.15 
    "Temperature used to linearize radiative heat transfer";

  parameter Real k(min=0, max=1)=1 
    "Coefficient used to scale convection between shade and glass";
  Modelica.Blocks.Interfaces.RealInput u 
    "Input connector, used to scale the surface area to take into account an operable shading device";
    

  Modelica.Blocks.Interfaces.RealInput Gc 
    "Signal representing the convective thermal conductance in [W/K]";
  Modelica.Blocks.Interfaces.RealInput QAbs_flow(unit="W", quantity="Power") 
    "Solar radiation absorbed by shade";

  Interfaces.RadiosityInflow JIn_air(start=A*0.8*Modelica.Constants.sigma*293.15^4) 
    "Incoming radiosity at the air-side surface of the shade";
  Interfaces.RadiosityInflow JIn_glass(start=A*0.8*Modelica.Constants.sigma*293.15^4) 
    "Incoming radiosity at the glass-side surface of the shade";
  Interfaces.RadiosityOutflow JOut_air 
    "Outgoing radiosity at the air-side surface of the shade";
  Interfaces.RadiosityOutflow JOut_glass 
    "Outgoing radiosity at the glass-side surface of the shade";

  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_a air 
    "Port that connects to the air (room or outside)";
  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_b glass 
    "Heat port that connects to shaded part of glass";
 Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_a sha(T(start=293.15)) 
    "Heat port to shade";
protected 
 final parameter Real T03(min=0, unit="K3")=T0^3 "3rd power of temperature T0";
 Real T4(min=1E8, start=293.15^4, nominal=1E10, unit="K4") 
    "4th power of temperature";
 Modelica.SIunits.RadiantPower E_air "Emissive power of surface that faces air";
 Modelica.SIunits.RadiantPower E_glass 
    "Emissive power of surface that faces glass";
equation 
  if thisSideHasShade then
  // Radiosities that are outgoing from the surface, which are
  // equal to the infrared absorptivity plus the reflected incoming
  // radiosity plus the radiosity that is transmitted from the
  // other surface.
    if linearize then
      T4 = T03 * sha.T;
    else
      if homotopyInitialization then
 T4 = homotopy(actual=(sha.T)^4, simplified=T03 * sha.T);
      else
 T4 = (sha.T)^4;
      end if;
    end if;

    E_air   = u * A * absIR_air   * Modelica.Constants.sigma * T4;
    E_glass = u * A * absIR_glass * Modelica.Constants.sigma * T4;
    // Radiosity outgoing from shade towards air side and glass side
    JOut_air   = - E_air   - tauIR_glass * JIn_glass - rhoIR_air*JIn_air;
    JOut_glass = - E_glass - tauIR_air   * JIn_air   - rhoIR_glass*JIn_glass;
    // Heat balance of shade
    // The term 2*Gc is to combine the parallel convective heat transfer resistances,
    // see figure in info section.
    QAbs_flow + absIR_air*JIn_air + absIR_glass*JIn_glass
      = -Gc*(2*(air.T-sha.T)+k*(glass.T-sha.T))+E_air+E_glass;
    // Convective heat flow at air node
    air.Q_flow   = Gc*(2*(air.T-sha.T) + (air.T-glass.T));
    // Convective heat flow at glass node
    glass.Q_flow = Gc*((glass.T-air.T)+k*(glass.T-sha.T));
  else
    air.Q_flow   = Gc*(air.T-glass.T);
    glass.Q_flow = -air.Q_flow;
    sha.T = (air.T+glass.T)/2;
    T4 = T03 * T0;
    E_air = 0;
    E_glass = 0;
    JOut_air = -JIn_glass;
    JOut_glass = -JIn_air;
  end if;

end Shade;

Buildings.HeatTransfer.Windows.BaseClasses.ShadeInterface_weatherBus

Information

Partial model to implement overhang and side fin model with weather bus as a connector.

Extends from Modelica.Blocks.Interfaces.BlockIcon (Basic graphical layout of input/output block).

Connectors

Type	Name	Description
Bus	weaBus	Weather data bus
input RealInput	incAng	Solar incidence angle [rad]
input RealInput	HDirTilUns	Direct solar irradiation on tilted, unshaded surface [W/m2]
output RealOutput	HDirTil	Direct solar irradiation on tilted, shaded surface [W/m2]
output RealOutput	fraSun	Fraction of the area that is unshaded [1]

Modelica definition

partial model ShadeInterface_weatherBus 
  "Base class for models of window shade and overhangs"
  extends Modelica.Blocks.Interfaces.BlockIcon;

  Buildings.BoundaryConditions.WeatherData.Bus weaBus "Weather data bus";

  Modelica.Blocks.Interfaces.RealInput incAng(quantity="Angle",
                                              unit="rad",
                                              displayUnit="rad") 
    "Solar incidence angle";

  Modelica.Blocks.Interfaces.RealInput HDirTilUns(
                         quantity="RadiantEnergyFluenceRate",
                         unit="W/m2") 
    "Direct solar irradiation on tilted, unshaded surface";

  Modelica.Blocks.Interfaces.RealOutput HDirTil(
                         quantity="RadiantEnergyFluenceRate",
                         unit="W/m2") 
    "Direct solar irradiation on tilted, shaded surface";
  Modelica.Blocks.Interfaces.RealOutput fraSun(final min=0,
                                               final max=1,
                                               final unit="1") 
    "Fraction of the area that is unshaded";

end ShadeInterface_weatherBus;

Buildings.HeatTransfer.Windows.BaseClasses.ShadingSignal

Information

Extends from Modelica.Blocks.Interfaces.SO (Single Output continuous control block).

Parameters

Type	Name	Default	Description
Boolean	haveShade		Set to true if a shade is present

Connectors

Type	Name	Description
output RealOutput	y	Connector of Real output signal
input RealInput	u	Shading control signal, 0: unshaded; 1: fully shaded
output RealOutput	yCom	1-u

Modelica definition

block ShadingSignal 
  "Converts the shading signal to be strictly bigger than 0 and smaller than 1"
  extends Modelica.Blocks.Interfaces.SO;
  parameter Boolean haveShade "Set to true if a shade is present";
  Modelica.Blocks.Interfaces.RealInput u if haveShade 
    "Shading control signal, 0: unshaded; 1: fully shaded";
  Modelica.Blocks.Interfaces.RealOutput yCom "1-u";
protected 
  constant Real y0 = 1E-6 "Smallest allowed value for y if a shade is present";
  constant Real k = 1-2*y0 "Gain for shading signal";
  Modelica.Blocks.Interfaces.RealInput u_in_internal 
    "Needed to connect to conditional connector";
equation 
  connect(u, u_in_internal);
  if not haveShade then
    u_in_internal = 0;
  end if;
  if haveShade then
    y = y0 + k *  u_in_internal;
    yCom = 1-y;
  else
    y = 0;
    yCom = 1;
  end if;
end ShadingSignal;

Buildings.HeatTransfer.Windows.BaseClasses.SideFins

Information

For a window with side fins, this block outputs the fraction of the area that is exposed to the sun. This models can also be used for doors with side fins.

Input to this block are the wall solar azimuth angle and the altitude angle of the sun. These angles can be calculated using blocks from the package Buildings.BoundaryConditions.SolarGeometry.BaseClasses.

Limitations

The model assumes that

• the side fins are placed symmetrically to the left and right of the window,
• the top of the side fins must be at an equal or greater height than the window, and
• the bottom of the side fins must be at an equal or lower height than the bottom of the window.

Implementation

The method of super position is used to calculate the shaded area of the window. The area besides the side fin is divided as shown in the figure below.

Variables used in the code for the rectangle AEGI, BEGH, DFGI and CFGH are shown in figure below.

The rectangles AEGI, BEGH, DFGI and CFGH have the same geometric configuration with respect to the side fin. Thus, the same algorithm is used to calculate the shaded portion in these areas. A single equation in the for loop improves the total calculation time, as compared to if-then-else conditions, considering the various shapes of the shaded portions. To find the shaded area in the window ABCD, the shaded portion of BEGH and DFGI is subtracted from AEGI and CFGH. This shaded area of the window is then divided by the total window area to calculate the shaded fraction of the window.

Extends from Modelica.Blocks.Interfaces.BlockIcon (Basic graphical layout of input/output block), Buildings.Rooms.BaseClasses.SideFins (Record for window side fins).

Parameters

Type	Name	Default	Description
Side fin
Length	h		Height of side fin that extends above window, measured from top of window [m]
Length	dep		Side fin depth (measured perpendicular to the wall plane) [m]
Length	gap		Distance between side fin and window edge [m]
Window
Length	hWin		Window height [m]
Length	wWin		Window width [m]

Connectors

Type	Name	Description
input RealInput	alt	Solar altitude angle (angle between sun ray and horizontal surface) [rad]
input RealInput	verAzi	Angle between projection of sun's rays and normal to vertical surface [rad]
output RealOutput	fraSun	Fraction of window area exposed to the sun [1]

Modelica definition

block SideFins 
  "For a window with side fins, outputs the fraction of the area that is sun exposed"
  extends Modelica.Blocks.Interfaces.BlockIcon;
  extends Buildings.Rooms.BaseClasses.SideFins;
  Modelica.Blocks.Interfaces.RealInput alt(quantity="Angle",
                                           unit="rad",
                                           displayUnit="deg") 
    "Solar altitude angle (angle between sun ray and horizontal surface)";
  Modelica.Blocks.Interfaces.RealInput verAzi(quantity="Angle",
                                              unit="rad",
                                              displayUnit="deg") 
    "Angle between projection of sun's rays and normal to vertical surface";
  Modelica.Blocks.Interfaces.RealOutput fraSun(final min=0,
                                               final max=1,
                                               final unit="1") 
    "Fraction of window area exposed to the sun";
// Window dimensions
  parameter Modelica.SIunits.Length hWin "Window height";
  parameter Modelica.SIunits.Length wWin "Window width";
// Other calculation variables
protected 
  final parameter Modelica.SIunits.Length tmpH[4]=
                  {h+hWin, h, h+hWin, h} 
    "Height of rectangular sections used for superposition";
  final parameter Modelica.SIunits.Length tmpW[4]=
                  {gap + wWin,gap + wWin,gap, gap} 
    "Width of rectangular sections used for superpositions; c1,c2 etc";
  final parameter Modelica.SIunits.Length deltaL=wWin/100 
    "Fraction of window dimension over which min-max functions are smoothened";
  final parameter Modelica.SIunits.Area AWin=hWin*wWin "Window area";
  Modelica.SIunits.Length x1[4] 
    "Horizontal distance between side fin and point where shadow line and window lower edge intersects";
  Modelica.SIunits.Length x2 
    "Horizontal distance between side fin and shadow corner";
  Modelica.SIunits.Length x3[4] "Window width";
  Modelica.SIunits.Length y1[4] "Window height";
  Modelica.SIunits.Length y2 
    "Vertical distance between window upper edge and shadow corner";
  Modelica.SIunits.Length y3[4] 
    "Vertical distance between window upper edge and point where shadow line and window side edge intersects";
  Modelica.SIunits.Area area[4] 
    "Shaded areas of the sections used in superposition";
  Modelica.SIunits.Area shdArea "Shaded area";
  Modelica.SIunits.Area crShdArea "Final value of shaded area";
  Modelica.SIunits.Area crShdArea1 
    "Shaded area, corrected for the sun behind the surface/wall";
  Modelica.SIunits.Area crShdArea2 
    "Shaded area, corrected for the sun below horizon";
  Modelica.SIunits.Length minX[4];
  Modelica.SIunits.Length minY[4];
  Modelica.SIunits.Length minX2X3[4];
  Modelica.SIunits.Length minY2Y3[4];
  Real delta=1e-6 "Small number to avoid division by zero";
  Real tanLambda 
    "Tangent of angle between horizontal and sun ray projection on vertical wall";
  Real verAzi_t;
  Real lambda_t;
  Real verAzi_c;
  Real alt_t;
initial algorithm 
  assert(h >= 0, "Sidefin parameter 'h' must be at least zero.
  It is measured from the upper edge of the window to the top of the side fin.
  Received h = " + String(h));
equation 
  // This if-then construct below increases computing efficiency in
  // Buildings.HeatTransfer.Windows.FixedShade in case the window has no overhang.
  if haveSideFins then
  //avoiding division by zero
    lambda_t = Buildings.Utilities.Math.Functions.smoothMax(
      x1=tanLambda,
      x2=delta,
      deltaX=delta/10);
    verAzi_t = Buildings.Utilities.Math.Functions.smoothMax(
      x1=Modelica.Math.tan(verAzi),
      x2=delta,
      deltaX=delta/10);
    verAzi_c = Buildings.Utilities.Math.Functions.smoothMax(
      x1=Modelica.Math.cos(verAzi),
      x2=delta,
      deltaX=delta/10);
    alt_t = Buildings.Utilities.Math.Functions.smoothMax(
      x1=Modelica.Math.tan(alt),
      x2=delta,
      deltaX=delta/10);
    tanLambda = alt_t / verAzi_t;
    y2 = dep*alt_t/verAzi_c;
    x2 = dep*verAzi_t;
    for i in 1:4 loop
      x1[i] = tmpH[i]/lambda_t;
      x3[i] = tmpW[i];
      y1[i] = tmpH[i];
      y3[i] = tmpW[i]*lambda_t;
      minX2X3[i] = Buildings.Utilities.Math.Functions.smoothMin(
        x1=x2,
        x2=x3[i],
        deltaX=deltaL);
      minX[i] = Buildings.Utilities.Math.Functions.smoothMin(
        x1=x1[i],
        x2=minX2X3[i],
        deltaX=deltaL);
      minY2Y3[i] = Buildings.Utilities.Math.Functions.smoothMin(
        x1=y2,
        x2=y3[i],
        deltaX=deltaL);
      minY[i] = Buildings.Utilities.Math.Functions.smoothMin(
        x1=y1[i],
        x2=minY2Y3[i],
        deltaX=deltaL);
      area[i] = tmpH[i]*minX[i] - minX[i]*minY[i]/2;
    end for;
  //by superposition
    shdArea = area[1] + area[4] - area[2] - area[3];
    // The corrections below ensure that the shaded area is 1 if the
    // sun is below the horizon or behind the wall.
    // This correction is not required (because the direct solar irradiation
    // will be zero in this case), but it leads to more realistic time series
    // of this model.
  //correction case: Sun not in front of the wall
    crShdArea1 = Buildings.Utilities.Math.Functions.spliceFunction(
       pos=shdArea,
       neg=AWin,
       x=(Modelica.Constants.pi/2)-verAzi,
       deltax=0.01);
  //correction case: Sun below horizon
    crShdArea2 = Buildings.Utilities.Math.Functions.spliceFunction(
       pos=shdArea,
       neg=AWin,
       x=alt,
       deltax=0.01);
    crShdArea=Buildings.Utilities.Math.Functions.smoothMax(
       x1=crShdArea1,
       x2=crShdArea2,
       deltaX=0.0001*AWin);
    fraSun = 1-crShdArea/AWin;
  else
    lambda_t = 0;
    verAzi_t = 0;
    verAzi_c = 0;
    alt_t =    0;
    tanLambda = 0;
    y2 = 0;
    x2 = 0;
    x1 = fill(0.0, 4);
    x3 = fill(0.0, 4);
    y1 = fill(0.0, 4);
    y3 = fill(0.0, 4);
    minX2X3 = fill(0.0, 4);
    minX = fill(0.0, 4);
    minY2Y3 = fill(0.0, 4);
    minY = fill(0.0, 4);
    area = fill(0.0, 4);
    shdArea = 0;
    crShdArea1 = 0;
    crShdArea2 = 0;
    crShdArea  = 0;
    fraSun     = 0;
  end if;
end SideFins;

Buildings.HeatTransfer.Windows.BaseClasses.PartialConvection

Information

Partial model for heat convection of a window surface with or without shade, that is outside or inside the room.

Convective heat transfer is modeled between the heat port air and the shade, if present, the glass and the frame. If the parameter haveShade is set to true, then a shade is present and the input port QAbs_flow needs to be connected to a model that computes the solar radiation that is absorbed by the shade. If haveShade=true, then the model shade and the connectors QAbs_flow, glaSha, JInSha and JOutSha are removed. This allows using the model as a base class for windows with inside shade, outside shade, or no shade.

Parameters

Type	Name	Default	Description
Area	A		Heat transfer area of frame and window [m2]
Real	fFra		Fraction of window frame divided by total window area
Boolean	linearizeRadiation		Set to true to linearize emissive power
Shading
Emissivity	absIRSha_air		Infrared absorptivity of shade surface that faces air [1]
Emissivity	absIRSha_glass		Infrared absorptivity of shade surface that faces glass [1]
TransmissionCoefficient	tauIRSha_air		Infrared transmissivity of shade for radiation coming from the exterior or the room [1]
TransmissionCoefficient	tauIRSha_glass		Infrared transmissivity of shade for radiation coming from the glass [1]
Boolean	haveExteriorShade		Set to true if window has exterior shade (at surface a)
Boolean	haveInteriorShade		Set to true if window has interior shade (at surface b)
Boolean	thisSideHasShade		Set to true if this side of the model has a shade

Connectors

Type	Name	Description
input RealInput	uSha	Input connector, used to scale the surface area to take into account an operable shading device, 0: unshaded; 1: fully shaded
HeatPort_a	air	Port that connects to the air (room or outside)
HeatPort_b	glaUns	Heat port that connects to unshaded part of glass
HeatPort_b	glaSha	Heat port that connects to shaded part of glass
HeatPort_a	frame	Heat port at window frame
output RadiosityOutflow	JOutUns	Outgoing radiosity that connects to unshaded part of glass [W]
input RadiosityInflow	JInUns	Incoming radiosity that connects to unshaded part of glass [W]
output RadiosityOutflow	JOutSha	Outgoing radiosity that connects to shaded part of glass [W]
input RadiosityInflow	JInSha	Incoming radiosity that connects to shaded part of glass [W]
input RealInput	QAbs_flow	Solar radiation absorbed by shade [W]

Modelica definition

partial model PartialConvection 
  "Partial model for heat convection between a possibly shaded window that can be outside or inside the room"
  parameter Modelica.SIunits.Area A "Heat transfer area of frame and window";
  parameter Real fFra "Fraction of window frame divided by total window area";
  final parameter Modelica.SIunits.Area AFra = fFra * A "Frame area";
  final parameter Modelica.SIunits.Area AGla = A-AFra "Glass area";

  parameter Modelica.SIunits.Emissivity absIRSha_air 
    "Infrared absorptivity of shade surface that faces air";
  parameter Modelica.SIunits.Emissivity absIRSha_glass 
    "Infrared absorptivity of shade surface that faces glass";

  parameter Modelica.SIunits.TransmissionCoefficient tauIRSha_air 
    "Infrared transmissivity of shade for radiation coming from the exterior or the room";
  parameter Modelica.SIunits.TransmissionCoefficient tauIRSha_glass 
    "Infrared transmissivity of shade for radiation coming from the glass";

  parameter Boolean linearizeRadiation 
    "Set to true to linearize emissive power";

  parameter Boolean haveExteriorShade 
    "Set to true if window has exterior shade (at surface a)";
  parameter Boolean haveInteriorShade 
    "Set to true if window has interior shade (at surface b)";

  final parameter Boolean windowHasShade = haveExteriorShade or haveInteriorShade 
    "Set to true if window system has a shade";
  parameter Boolean thisSideHasShade 
    "Set to true if this side of the model has a shade";

  Modelica.Blocks.Interfaces.RealInput uSha if windowHasShade 
    "Input connector, used to scale the surface area to take into account an operable shading device, 0: unshaded; 1: fully shaded";
    

  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_a air 
    "Port that connects to the air (room or outside)";
  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_b glaUns 
    "Heat port that connects to unshaded part of glass";

  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_b glaSha if windowHasShade 
    "Heat port that connects to shaded part of glass";

  Modelica.Thermal.HeatTransfer.Components.Convection conWinUns 
    "Convection from unshaded part of window to outside or room air";

  Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_a frame 
    "Heat port at window frame";
  Modelica.Thermal.HeatTransfer.Components.Convection conFra 
    "Convective heat transfer between air and frame";

protected 
  Modelica.Blocks.Math.Product proUns "Product for unshaded part of window";

  Modelica.Blocks.Math.Product proSha if windowHasShade 
    "Product for shaded part of window";

public 
  ShadingSignal shaSig(haveShade=windowHasShade) 
    "Conversion for shading signal";
  Shade shade(
    final thisSideHasShade = thisSideHasShade,
    final A=AGla,
    final linearize=linearizeRadiation,
    final absIR_air=if thisSideHasShade then absIRSha_air else 0,
    final absIR_glass=if thisSideHasShade then absIRSha_glass else 0,
    final tauIR_air=if thisSideHasShade then tauIRSha_air else 1,
    final tauIR_glass=if thisSideHasShade then tauIRSha_glass else 1) if 
       windowHasShade "Heat balance of shade";
  Interfaces.RadiosityOutflow JOutUns 
    "Outgoing radiosity that connects to unshaded part of glass";
  Interfaces.RadiosityInflow JInUns 
    "Incoming radiosity that connects to unshaded part of glass";
public 
  Interfaces.RadiosityOutflow JOutSha if windowHasShade 
    "Outgoing radiosity that connects to shaded part of glass";
  Interfaces.RadiosityInflow JInSha if windowHasShade 
    "Incoming radiosity that connects to shaded part of glass";
protected 
  Radiosity.RadiositySplitter radShaOut "Radiosity that strikes shading device";

public 
  Modelica.Blocks.Interfaces.RealInput QAbs_flow(unit="W", quantity="Power") if windowHasShade 
    "Solar radiation absorbed by shade";
initial equation 
  assert(( thisSideHasShade and windowHasShade)  or (not thisSideHasShade),
    "Parameters \"thisSideHasShade\" and \"windowHasShade\" are not consistent. Check parameters");


equation 
  connect(conWinUns.fluid, air);

  connect(conFra.fluid, air);

  connect(conFra.solid, frame);
  connect(glaUns, conWinUns.solid);
  connect(proUns.y, conWinUns.Gc);
  connect(uSha, shaSig.u);
  connect(proSha.u2, shaSig.y);
  connect(shaSig.yCom, proUns.u1);
  connect(shade.Gc, proSha.y);
  connect(shade.air, air);
  connect(shade.glass, glaSha);
  connect(radShaOut.JOut_2,JOutUns);
  connect(shade.JOut_glass,JOutSha);
  connect(shade.JIn_glass,JInSha);
  connect(shaSig.y,radShaOut. u);
  connect(radShaOut.JOut_1, shade.JIn_air);
  connect(shade.u, shaSig.y);

  connect(shade.QAbs_flow, QAbs_flow);
end PartialConvection;

Buildings.HeatTransfer.Windows.BaseClasses.PartialRadiation

Information

References

• Michael Wetter.
  Simulation-based Building Energy Optimization.
  Dissertation. University of California at Berkeley. 2004.

Extends from Modelica.Blocks.Interfaces.BlockIcon (Basic graphical layout of input/output block), Buildings.HeatTransfer.Windows.BaseClasses.RadiationBaseData (Basic parameters for window radiation calculation).

Parameters

Type	Name	Default	Description
Boolean	haveExteriorShade		Set to true if window has an exterior shade
Boolean	haveInteriorShade		Set to true if window has an interior shade
Area	AWin		Area of window [m2]
Glass
Integer	N		Number of glass layers
Length	xGla[N]		Thickness of glass [m]
TransmissionCoefficient	tauGlaSol[N]		Solar transmissivity of glass [1]
ReflectionCoefficient	rhoGlaSol_a[N]		Solar reflectivity of glass at surface a (facing outside) [1]
ReflectionCoefficient	rhoGlaSol_b[N]		Solar reflectivity of glass at surface b (facing room-side) [1]
Shade
TransmissionCoefficient	tauShaSol_a		Solar transmissivity of shade for irradiation from air-side [1]
TransmissionCoefficient	tauShaSol_b		Solar transmissivity of shade for irradiation from glass-side [1]
ReflectionCoefficient	rhoShaSol_a		Solar reflectivity of shade for irradiation from air-side [1]
ReflectionCoefficient	rhoShaSol_b		Solar reflectivity of shade for irradiation from glass-side [1]

Connectors

Type	Name	Description
input RealInput	uSha	Control signal for shading (0: unshaded; 1: fully shaded)
input RealInput	HDif	Diffussive solar radiation [W/m2]
input RealInput	incAng	Incident angle [rad]
input RealInput	HDir	Direct solar radiation [W/m2]

Modelica definition

partial block PartialRadiation 
  "Partial model for variables and data used in radiation calculation"
  extends Modelica.Blocks.Interfaces.BlockIcon;
  extends Buildings.HeatTransfer.Windows.BaseClasses.RadiationBaseData;

  ////////////////// Parameters that are not used by RadiationData
  parameter Boolean haveExteriorShade 
    "Set to true if window has an exterior shade";
  parameter Boolean haveInteriorShade 
    "Set to true if window has an interior shade";
  parameter Modelica.SIunits.Area AWin "Area of window";

  ////////////////// Derived parameters
  final parameter Boolean haveShade=haveExteriorShade or haveInteriorShade 
    "Set to true if window has a shade";
  final parameter Buildings.HeatTransfer.Windows.BaseClasses.RadiationData
    radDat(
    final N=N,
    final tauGlaSol=tauGlaSol,
    final rhoGlaSol_a=rhoGlaSol_a,
    final rhoGlaSol_b=rhoGlaSol_b,
    final xGla=xGla,
    final tauShaSol_a=tauShaSol_a,
    final tauShaSol_b=tauShaSol_b,
    final rhoShaSol_a=rhoShaSol_a,
    final rhoShaSol_b=rhoShaSol_b) 
    "Optical properties of window for different irradiation angles";
  Modelica.Blocks.Interfaces.RealInput uSha(min=0, max=1) if haveShade 
    "Control signal for shading (0: unshaded; 1: fully shaded)";
  Modelica.Blocks.Interfaces.RealInput HDif(quantity="RadiantEnergyFluenceRate",
      unit="W/m2") "Diffussive solar radiation";
  Modelica.Blocks.Interfaces.RealInput incAng(
    final quantity="Angle",
    final unit="rad",
    displayUnit="deg") "Incident angle";
  Modelica.Blocks.Interfaces.RealInput HDir(quantity="RadiantEnergyFluenceRate",
      unit="W/m2") "Direct solar radiation";

protected 
  Modelica.Blocks.Interfaces.RealInput uSha_internal(min=0, max=1) 
    "Control signal for shading (0: unshaded; 1: fully shaded)";
initial equation 
  /* Current model assumes that the window only has either an interior or exterior shade.
     Warn user if it has an interior and exterior shade. 
     Allowing both shades at the same time would require rewriting part of the model. */
  assert(not (haveExteriorShade and haveInteriorShade),
    "Window radiation model does not support an exterior and interior shade at the same time.");
equation 
  // Connect statement for conditionally removed connector uSha
  connect(uSha, uSha_internal);
  if (not haveShade) then
    uSha_internal = 0;
  end if;
end PartialRadiation;

Buildings.HeatTransfer.Windows.BaseClasses.PartialShade_weatherBus

Information

Partial model to implement overhang and side fin model with weather bus as a connector.

Extends from Buildings.HeatTransfer.Windows.BaseClasses.ShadeInterface_weatherBus (Base class for models of window shade and overhangs).

Parameters

Type	Name	Default	Description
Window
Length	hWin		Window height [m]
Length	wWin		Window width [m]

Connectors

Type	Name	Description
Bus	weaBus	Weather data bus
input RealInput	incAng	Solar incidence angle [rad]
input RealInput	HDirTilUns	Direct solar irradiation on tilted, unshaded surface [W/m2]
output RealOutput	HDirTil	Direct solar irradiation on tilted, shaded surface [W/m2]
output RealOutput	fraSun	Fraction of the area that is unshaded [1]

Modelica definition

partial model PartialShade_weatherBus 
  "Partial model to implement overhang and side fins with weather bus connector"
  extends Buildings.HeatTransfer.Windows.BaseClasses.ShadeInterface_weatherBus;
  // Window dimensions
  parameter Modelica.SIunits.Length hWin "Window height";
  parameter Modelica.SIunits.Length wWin "Window width";

protected 
  Buildings.BoundaryConditions.SolarGeometry.BaseClasses.WallSolarAzimuth walSolAzi 
    "Wall solar azimuth";

  Modelica.Blocks.Math.Product product;

equation 
  connect(weaBus.sol.alt, walSolAzi.alt);
  connect(walSolAzi.incAng, incAng);
  connect(product.y, HDirTil);
  connect(product.u1, HDirTilUns);
end PartialShade_weatherBus;

Buildings.HeatTransfer.Windows.BaseClasses.TransmittedRadiation

Information

The transmitted exterior radiation for window system includes:

1. the transmitted diffusive radiation on unshaded part: AWin*(1-uSha)*HDif*tau(HEM)
2. the transmitted direct radiation on no shade part: AWin*(1-uSha)*HDir*tau(IncAng)
3. the transmitted diffusive radiation on shaded part: AWin*uSha*HDif*tauSha(HEM)
4. the transmitted direct radiation on shaded part: AWin*uSha*HDir*tauSha(IncAng);

References

• Michael Wetter.
  Simulation-based Building Energy Optimization.
  Dissertation. University of California at Berkeley. 2004.

Extends from Buildings.HeatTransfer.Windows.BaseClasses.PartialRadiation (Partial model for variables and data used in radiation calculation).

Parameters

Type	Name	Default	Description
Boolean	haveExteriorShade		Set to true if window has an exterior shade
Boolean	haveInteriorShade		Set to true if window has an interior shade
Area	AWin		Area of window [m2]
Glass
Integer	N		Number of glass layers
Length	xGla[N]		Thickness of glass [m]
TransmissionCoefficient	tauGlaSol[N]		Solar transmissivity of glass [1]
ReflectionCoefficient	rhoGlaSol_a[N]		Solar reflectivity of glass at surface a (facing outside) [1]
ReflectionCoefficient	rhoGlaSol_b[N]		Solar reflectivity of glass at surface b (facing room-side) [1]
Shade
TransmissionCoefficient	tauShaSol_a		Solar transmissivity of shade for irradiation from air-side [1]
TransmissionCoefficient	tauShaSol_b		Solar transmissivity of shade for irradiation from glass-side [1]
ReflectionCoefficient	rhoShaSol_a		Solar reflectivity of shade for irradiation from air-side [1]
ReflectionCoefficient	rhoShaSol_b		Solar reflectivity of shade for irradiation from glass-side [1]

Connectors

Type	Name	Description
input RealInput	uSha	Control signal for shading (0: unshaded; 1: fully shaded)
input RealInput	HDif	Diffussive solar radiation [W/m2]
input RealInput	incAng	Incident angle [rad]
input RealInput	HDir	Direct solar radiation [W/m2]
output RealOutput	QTra_flow	Transmitted exterior radiation through the window. (1: no shade; 2: shade) [W]

Modelica definition

block TransmittedRadiation "Transmitted radiation through window"
  extends Buildings.HeatTransfer.Windows.BaseClasses.PartialRadiation;
  Modelica.Blocks.Interfaces.RealOutput QTra_flow(final quantity="Power",
      final unit="W") 
    "Transmitted exterior radiation through the window. (1: no shade; 2: shade)";
  final parameter Real traCoeRoo(fixed=false) 
    "Transmitivity of the window glass for interior radiation without shading";

  output Modelica.SIunits.Power QTraUns_flow 
    "Transmitted solar radiation through unshaded part of window";
  output Modelica.SIunits.Power QTraSha_flow 
    "Transmitted solar radiation through shaded part of window";

protected 
  Integer k=1;
  Real x;
  final parameter Integer NDIR=radDat.NDIR;
  final parameter Integer HEM=radDat.HEM;
  constant Integer NoShade=1;
  constant Integer Shade=2;
  constant Integer Interior=1;
  constant Integer Exterior=2;
  final parameter Real coeTraWinExtIrr[2, radDat.HEM + 2](fixed=false);
  Real tmpNoSha;
  Real tmpSha;
  Real incAng2;

initial algorithm 
  //**************************************************************
  // Assign coefficients.
  // Data dimension from Orginal ([1 : HEM]) to New ([2 : HEM+1])
  // with 2 dummy variable for interpolation.
  //**************************************************************
  // Glass
  for j in 1:HEM loop
    // Properties for glass without shading
    coeTraWinExtIrr[NoShade, j + 1] := radDat.traRef[1, 1, N, j];
    // Properties for glass with shading
    if haveInteriorShade then
      coeTraWinExtIrr[Shade, j + 1] := radDat.winTraExtIrrIntSha[j];
    elseif haveExteriorShade then
      coeTraWinExtIrr[Shade, j + 1] := radDat.winTraExtIrrExtSha[j];
    else
      // No Shade
      coeTraWinExtIrr[Shade, j + 1] := 0.0;
    end if;
  end for;
  // Dummy variables at 1 and HEM+2
  for k in NoShade:Shade loop
    coeTraWinExtIrr[k, 1] := coeTraWinExtIrr[k, 2];
    coeTraWinExtIrr[k, HEM + 2] := coeTraWinExtIrr[k, HEM + 1];
  end for;

  //**************************************************************
  // Glass: transmissivity for interior irradiation
  //**************************************************************
  traCoeRoo := radDat.traRef[1, N, 1, HEM];

algorithm 
  QTraUns_flow := AWin*HDif*(1 - uSha_internal)*coeTraWinExtIrr[NoShade, HEM +
    1];
  QTraSha_flow := AWin*HDif*uSha_internal*coeTraWinExtIrr[Shade, HEM + 1];

  //**************************************************************
  // Glass, Device: add absorbed radiation (angular part) from exterior sources
  //**************************************************************
  // Use min() instead of if() to avoid event
  incAng2 := min(incAng, 0.5*Modelica.Constants.pi);
  x := 2*(NDIR - 1)*abs(incAng2)/Modelica.Constants.pi 
    "x=(index-1)*incAng/(0.5pi), 0<=x<=NDIR-1";
  x := x + 2;

  // Window unshaded parts: add transmitted radiation for angular radiation
  tmpNoSha :=
    Buildings.HeatTransfer.Windows.BaseClasses.smoothInterpolation({
    coeTraWinExtIrr[NoShade, k] for k in 1:(HEM + 2)}, x);
  QTraUns_flow := QTraUns_flow + AWin*HDir*(1 - uSha_internal)*tmpNoSha;

  // Window shaded parts: add transmitted radiation for angular radiation
  tmpSha := Buildings.HeatTransfer.Windows.BaseClasses.smoothInterpolation(
    {coeTraWinExtIrr[Shade, k] for k in 1:(HEM + 2)}, x);
  QTraSha_flow := QTraSha_flow + AWin*HDir*uSha_internal*tmpSha;

  // Assign quantities to output connectors
  QTra_flow := QTraUns_flow + QTraSha_flow;
end TransmittedRadiation;

Buildings.HeatTransfer.Windows.BaseClasses.WindowRadiation

Information

The absorbed radiation by exterior shades includes:

1. the directly absorbed exterior radiation: AWin*uSha*(HDir+HDif)*(1-tau-rho)
2. the indirectly absorbed exterior radiantion from reflection (angular part): AWin*uSha*HDir*tau*rho(IncAng)*(1-tau-rho)
3. the indirectly absorbed of exterior irradiantion from reflection (diffusive part): AWin*uSha*HDif*tau*rho(HEM)*(1-tau-rho)
4. the absorbed interior radiation is neglected.

The absorbed radiation by interior shades includes:

1. the absorbed exterior radiation (angular part): AWin*uSha*HDir*alpha(IncAng)
2. the absorbed exterior radiation (diffusive part): AWin*uSha*HDif*alpha(HEM)
3. the absorbed interior radiation (diffusive part): AWin*uSha*HRoo*(1-tau-rho)

The absorbed radiation by glass includes:

1. the absorbed radiation by unshaded part (diffusive part): AWin*(1-uSha)*(HDif*alphaEx(HEM)+HRoo*alphaIn(HEM))
2. the absorbed radiation by unshaded part (angualr part from exterior source): AWin*(1-uSha)*HDir*alphaEx(IncAng)
3. the absorbed radiaiton by shaded part (diffusive part): AWin*uSha*(HDif*alphaExSha(HEM)+HRoo*alphaInSha(HEM))
4. the absorbed radiation by shaded part (angular part from exterior source): AWin*uSha*HDir*alphaExSha(IncAng)

The transmitted exterior radiation for window system includes:

1. the transmitted diffusive radiation on unshaded part: AWin*(1-uSha)*HDif*tau(HEM)
2. the transmitted direct radiation on no shade part: AWin*(1-uSha)*HDir*tau(IncAng)
3. the transmitted diffusive radiation on shaded part: AWin*uSha*HDif*tauSha(HEM)
4. the transmitted direct radiation on shaded part: AWin*uSha*HDir*tauSha(IncAng);

References

• Michael Wetter.
  Simulation-based Building Energy Optimization.
  Dissertation. University of California at Berkeley. 2004.

Extends from Buildings.HeatTransfer.Windows.BaseClasses.PartialRadiation (Partial model for variables and data used in radiation calculation).

Parameters

Type	Name	Default	Description
Boolean	haveExteriorShade		Set to true if window has an exterior shade
Boolean	haveInteriorShade		Set to true if window has an interior shade
Area	AWin		Area of window [m2]
Glass
Integer	N		Number of glass layers
Length	xGla[N]		Thickness of glass [m]
TransmissionCoefficient	tauGlaSol[N]		Solar transmissivity of glass [1]
ReflectionCoefficient	rhoGlaSol_a[N]		Solar reflectivity of glass at surface a (facing outside) [1]
ReflectionCoefficient	rhoGlaSol_b[N]		Solar reflectivity of glass at surface b (facing room-side) [1]
Shade
TransmissionCoefficient	tauShaSol_a		Solar transmissivity of shade for irradiation from air-side [1]
TransmissionCoefficient	tauShaSol_b		Solar transmissivity of shade for irradiation from glass-side [1]
ReflectionCoefficient	rhoShaSol_a		Solar reflectivity of shade for irradiation from air-side [1]
ReflectionCoefficient	rhoShaSol_b		Solar reflectivity of shade for irradiation from glass-side [1]

Connectors

Type	Name	Description
input RealInput	uSha	Control signal for shading (0: unshaded; 1: fully shaded)
input RealInput	HDif	Diffussive solar radiation [W/m2]
input RealInput	incAng	Incident angle [rad]
input RealInput	HDir	Direct solar radiation [W/m2]
input RealInput	HRoo	Diffussive radiation from room [W/m2]
output RealOutput	QTra_flow	Transmitted exterior radiation through the window. (1: no shade; 2: shade) [W]
output RealOutput	QAbsExtSha_flow	Absorbed interior and exterior radiation by exterior shading device [W]
output RealOutput	QAbsIntSha_flow	Absorbed interior and exterior radiation by interior shading device [W]
output RealOutput	QAbsGlaUns_flow[N]	Absorbed interior and exterior radiation by unshaded part of glass [W]
output RealOutput	QAbsGlaSha_flow[N]	Absorbed interior and exterior radiation by shaded part of glass [W]

Modelica definition

block WindowRadiation "Calculation radiation for window"

  extends Buildings.HeatTransfer.Windows.BaseClasses.PartialRadiation;

  Modelica.Blocks.Interfaces.RealInput HRoo(quantity="RadiantEnergyFluenceRate",
      unit="W/m2") "Diffussive radiation from room ";
  Modelica.Blocks.Interfaces.RealOutput QTra_flow(final quantity="Power",
      final unit="W") 
    "Transmitted exterior radiation through the window. (1: no shade; 2: shade)";

  Modelica.Blocks.Interfaces.RealOutput QAbsExtSha_flow(final quantity="Power",
      final unit="W") 
    "Absorbed interior and exterior radiation by exterior shading device";
  Modelica.Blocks.Interfaces.RealOutput QAbsIntSha_flow(final quantity="Power",
      final unit="W") 
    "Absorbed interior and exterior radiation by interior shading device";
  Modelica.Blocks.Interfaces.RealOutput QAbsGlaUns_flow[N](each quantity=
        "Power", each final unit="W") 
    "Absorbed interior and exterior radiation by unshaded part of glass";
  Modelica.Blocks.Interfaces.RealOutput QAbsGlaSha_flow[N](each quantity=
        "Power", each final unit="W") 
    "Absorbed interior and exterior radiation by shaded part of glass";

  Buildings.HeatTransfer.Windows.BaseClasses.TransmittedRadiation tra(
    final N=N,
    final tauGlaSol=tauGlaSol,
    final rhoGlaSol_a=rhoGlaSol_a,
    final rhoGlaSol_b=rhoGlaSol_b,
    final xGla=xGla,
    final tauShaSol_a=tauShaSol_a,
    final rhoShaSol_a=rhoShaSol_a,
    final rhoShaSol_b=rhoShaSol_b,
    final haveExteriorShade=haveExteriorShade,
    final haveInteriorShade=haveInteriorShade,
    final AWin=AWin,
    final tauShaSol_b=tauShaSol_b);
  Buildings.HeatTransfer.Windows.BaseClasses.AbsorbedRadiation abs(
    final N=N,
    final tauGlaSol=tauGlaSol,
    final rhoGlaSol_a=rhoGlaSol_a,
    final rhoGlaSol_b=rhoGlaSol_b,
    final xGla=xGla,
    final tauShaSol_a=tauShaSol_a,
    final tauShaSol_b=tauShaSol_b,
    final rhoShaSol_a=rhoShaSol_a,
    final rhoShaSol_b=rhoShaSol_b,
    final haveExteriorShade=haveExteriorShade,
    final haveInteriorShade=haveInteriorShade,
    final AWin=AWin);
protected 
  final parameter Boolean noShade=not (haveExteriorShade or haveInteriorShade) 
    "Flag, true if the window has a shade";
equation 
  if noShade then
    assert(uSha_internal < 1E-6,
      "Window has no shade, but control signal is non-zero.\n" +
      "  Received uSha_internal = " + String(uSha_internal));
  end if;
  connect(HDif, tra.HDif);
  connect(HDif, abs.HDif);
  connect(HDir, tra.HDir);
  connect(HDir, abs.HDir);
  connect(incAng, tra.incAng);
  connect(incAng, abs.incAng);
  connect(HRoo, abs.HRoo);
  connect(tra.uSha, uSha);
  connect(abs.uSha, uSha);
  connect(tra.QTra_flow, QTra_flow);
  connect(abs.QAbsIntSha_flow, QAbsIntSha_flow);
  connect(abs.QAbsGlaSha_flow, QAbsGlaSha_flow);
  connect(abs.QAbsGlaUns_flow, QAbsGlaUns_flow);
  connect(abs.QAbsExtSha_flow, QAbsExtSha_flow);
end WindowRadiation;

Buildings.HeatTransfer.Windows.BaseClasses.RadiationBaseData

Information

Parameters

Type	Name	Default	Description
Glass
Integer	N		Number of glass layers
Length	xGla[N]		Thickness of glass [m]
TransmissionCoefficient	tauGlaSol[N]		Solar transmissivity of glass [1]
ReflectionCoefficient	rhoGlaSol_a[N]		Solar reflectivity of glass at surface a (facing outside) [1]
ReflectionCoefficient	rhoGlaSol_b[N]		Solar reflectivity of glass at surface b (facing room-side) [1]
Shade
TransmissionCoefficient	tauShaSol_a		Solar transmissivity of shade for irradiation from air-side [1]
TransmissionCoefficient	tauShaSol_b		Solar transmissivity of shade for irradiation from glass-side [1]
ReflectionCoefficient	rhoShaSol_a		Solar reflectivity of shade for irradiation from air-side [1]
ReflectionCoefficient	rhoShaSol_b		Solar reflectivity of shade for irradiation from glass-side [1]

Modelica definition

partial record RadiationBaseData 
  "Basic parameters for window radiation calculation"

  parameter Integer N(min=1) "Number of glass layers";
  parameter Modelica.SIunits.Length xGla[N] "Thickness of glass";
  parameter Modelica.SIunits.TransmissionCoefficient tauGlaSol[N] 
    "Solar transmissivity of glass";
  parameter Modelica.SIunits.ReflectionCoefficient rhoGlaSol_a[N] 
    "Solar reflectivity of glass at surface a (facing outside)";
  parameter Modelica.SIunits.ReflectionCoefficient rhoGlaSol_b[N] 
    "Solar reflectivity of glass at surface b (facing room-side)";

  parameter Modelica.SIunits.TransmissionCoefficient tauShaSol_a 
    "Solar transmissivity of shade for irradiation from air-side";
  parameter Modelica.SIunits.TransmissionCoefficient tauShaSol_b 
    "Solar transmissivity of shade for irradiation from glass-side";
  parameter Modelica.SIunits.ReflectionCoefficient rhoShaSol_a 
    "Solar reflectivity of shade for irradiation from air-side";
  parameter Modelica.SIunits.ReflectionCoefficient rhoShaSol_b 
    "Solar reflectivity of shade for irradiation from glass-side";

end RadiationBaseData;

Buildings.HeatTransfer.Windows.BaseClasses.RadiationData

Information

Extends from Modelica.Icons.Record (Icon for records), Buildings.HeatTransfer.Windows.BaseClasses.RadiationBaseData (Basic parameters for window radiation calculation).

Parameters

Type	Name	Default	Description
Glass
Integer	N		Number of glass layers
Length	xGla[N]		Thickness of glass [m]
TransmissionCoefficient	tauGlaSol[N]		Solar transmissivity of glass [1]
ReflectionCoefficient	rhoGlaSol_a[N]		Solar reflectivity of glass at surface a (facing outside) [1]
ReflectionCoefficient	rhoGlaSol_b[N]		Solar reflectivity of glass at surface b (facing room-side) [1]
Shade
TransmissionCoefficient	tauShaSol_a		Solar transmissivity of shade for irradiation from air-side [1]
TransmissionCoefficient	tauShaSol_b		Solar transmissivity of shade for irradiation from glass-side [1]
ReflectionCoefficient	rhoShaSol_a		Solar reflectivity of shade for irradiation from air-side [1]
ReflectionCoefficient	rhoShaSol_b		Solar reflectivity of shade for irradiation from glass-side [1]

Modelica definition

record RadiationData "Radiation data of a window"
  extends Modelica.Icons.Record;
  extends Buildings.HeatTransfer.Windows.BaseClasses.RadiationBaseData;
  final parameter Real glass[3, N]={tauGlaSol,rhoGlaSol_a,rhoGlaSol_b} 
    "Glass solar transmissivity, solar reflectivity at surface a and b, at normal incident angle";
  final parameter Real traRefShaDev[2, 2]={{tauShaSol_a,tauShaSol_b},{
      rhoShaSol_a,rhoShaSol_b}} "Shading device property";
  final parameter Integer NDIR=10 "Number of incident angles";
  final parameter Integer HEM=NDIR + 1 "Index of hemispherical integration";
  final parameter Modelica.SIunits.Angle psi[NDIR]=
      Buildings.HeatTransfer.Windows.Functions.getAngle(NDIR) 
    "Incident angles used for solar radiation calculation";
  final parameter Real layer[3, N, HEM]=
      Buildings.HeatTransfer.Windows.Functions.glassProperty(
      N,
      HEM,
      glass,
      xGla,
      psi) "Angular and hemispherical transmissivity, front (outside-facing) and back (room facing) reflectivity 
      of each glass pane";
  final parameter Real traRef[3, N, N, HEM]=
      Buildings.HeatTransfer.Windows.Functions.getGlassTR(
      N,
      HEM,
      layer) "Angular and hemispherical transmissivity, front (outside-facing) and back (room facing) reflectivity 
      between glass panes for exterior or interior irradiation without shading";
  final parameter Real absExtIrrNoSha[N, HEM]=
      Buildings.HeatTransfer.Windows.Functions.glassAbsExteriorIrradiationNoShading(
      traRef,
      N,
      HEM) "Angular and hemispherical absorptivity of each glass pane 
      for exterior irradiation without shading";
  final parameter Real absIntIrrNoSha[N]=
      Buildings.HeatTransfer.Windows.Functions.glassAbsInteriorIrradiationNoShading(
      traRef,
      N,
      HEM) "Hemispherical absorptivity of each glass pane 
      for interior irradiation without shading";
  final parameter Real winTraExtIrrExtSha[HEM]=
      Buildings.HeatTransfer.Windows.Functions.winTExteriorIrradiatrionExteriorShading(
      traRef,
      traRefShaDev,
      N,
      HEM) "Angular and hemispherical transmissivity of a window system (glass + exterior shading device) 
     for exterior irradiation";
  final parameter Real absExtIrrExtSha[N, HEM]=
      Buildings.HeatTransfer.Windows.Functions.glassAbsExteriorIrradiationExteriorShading(
      absExtIrrNoSha,
      traRef,
      traRefShaDev,
      N,
      HEM) "Angular and hemispherical absorptivity of each glass pane 
      for exterior irradiation with exterior shading";
  final parameter Real winTraExtIrrIntSha[HEM]=
      Buildings.HeatTransfer.Windows.Functions.winTExteriorIrradiationInteriorShading(
      traRef,
      traRefShaDev,
      N,
      HEM) "Angular and hemispherical transmissivity of a window system (glass and interior shading device) 
      for exterior irradiation";
  final parameter Real absExtIrrIntSha[N, HEM]=
      Buildings.HeatTransfer.Windows.Functions.glassAbsExteriorIrradiationInteriorShading(
      absExtIrrNoSha,
      traRef,
      traRefShaDev,
      N,
      HEM) "Angular and hemispherical absorptivity of each glass layer
     for exterior irradiation with interior shading";
  final parameter Real devAbsExtIrrIntShaDev[HEM]=
      Buildings.HeatTransfer.Windows.Functions.devAbsExteriorIrradiationInteriorShading(
      traRef,
      traRefShaDev,
      N,
      HEM) "Angular and hemispherical absorptivity of an interior shading device 
      for exterior irradiation";
  final parameter Real winTraRefIntIrrExtSha[3]=
      Buildings.HeatTransfer.Windows.Functions.winTRInteriorIrradiationExteriorShading(
      traRef,
      traRefShaDev,
      N,
      HEM) "Hemisperical transmissivity and reflectivity of a window system (glass and exterior shadig device) 
      for interior irradiation. traRefIntIrrExtSha[1]: transmissivity, 
      traRefIntIrrExtSha[2]: Back reflectivity; traRefIntIrrExtSha[3]: dummy value";
  final parameter Real absIntIrrExtSha[N]=
      Buildings.HeatTransfer.Windows.Functions.glassAbsInteriorIrradiationExteriorShading(
      absIntIrrNoSha,
      traRef,
      traRefShaDev,
      N,
      HEM) "Hemispherical absorptivity of each glass pane 
      for interior irradiation with exterior shading";
  final parameter Real absIntIrrIntSha[N]=
      Buildings.HeatTransfer.Windows.Functions.glassAbsInteriorIrradiationInteriorShading(
      absIntIrrNoSha,
      traRef,
      traRefShaDev,
      N,
      HEM) "Hemispherical absorptivity of each glass pane 
      for interior irradiation with interior shading";
  final parameter Real winTraRefIntIrrIntSha[3]=
      Buildings.HeatTransfer.Windows.Functions.winTRInteriorIrradiationInteriorShading(
      traRef,
      traRefShaDev,
      N,
      HEM) "Hemisperical transmissivity and back reflectivity of a window system (glass and interior shadig device) 
      for interior irradiation";
  final parameter Real devAbsIntIrrIntSha=
      Buildings.HeatTransfer.Windows.Functions.devAbsInteriorIrradiationInteriorShading(
      traRef,
      traRefShaDev,
      N,
      HEM) 
    "Hemiperical absorptivity of an interior shading device for interior irradiation";
end RadiationData;

Buildings.HeatTransfer.Windows.BaseClasses.convectionVerticalCavity

Information

Function for convective heat transfer in vertical window cavity. The computation is according to TARCOG 2006, except that this implementation computes the convection coefficient as a function that is differentiable in the temperatures.

References

TARCOG 2006: Carli, Inc., TARCOG: Mathematical models for calculation of thermal performance of glazing systems with our without shading devices, Technical Report, Oct. 17, 2006.

Inputs

Type	Name	Default	Description
Generic	gas		Thermophysical properties of gas fill
Real	Ra		Raleigh number
Temperature	T_m		Temperature used for thermophysical properties [K]
TemperatureDifference	dT		Temperature difference used to compute q_flow = h*dT [K]
Area	h	1.5	Height of window [m2]
Real	deltaNu	0.1	Small value for Nusselt number, used for smoothing
Real	deltaRa	1E3	Small value for Raleigh number, used for smoothing

Outputs

Type	Name	Description
Real	Nu	Nusselt number
CoefficientOfHeatTransfer	hCon	Convective heat transfer coefficient [W/(m2.K)]
HeatFlux	q_flow	Convective heat flux [W/m2]

Modelica definition

function convectionVerticalCavity 
  "Free convection in vertical cavity"
  input Buildings.HeatTransfer.Data.Gases.Generic gas 
    "Thermophysical properties of gas fill";
  input Real Ra(min=0) "Raleigh number";
  input Modelica.SIunits.Temperature T_m 
    "Temperature used for thermophysical properties";
  input Modelica.SIunits.TemperatureDifference dT 
    "Temperature difference used to compute q_flow = h*dT";
  input Modelica.SIunits.Area h(min=0) = 1.5 "Height of window";
  input Real deltaNu(min=0.01) = 0.1 
    "Small value for Nusselt number, used for smoothing";
  input Real deltaRa(min=0.01) = 1E3 
    "Small value for Raleigh number, used for smoothing";
  output Real Nu(min=0) "Nusselt number";
  output Modelica.SIunits.CoefficientOfHeatTransfer hCon(min=0) 
    "Convective heat transfer coefficient";
  output Modelica.SIunits.HeatFlux q_flow "Convective heat flux";
protected 
  Real Nu_1(min=0) "Nusselt number";
  Real Nu_2(min=0) "Nusselt number";
algorithm 

  Nu_1 :=Buildings.Utilities.Math.Functions.spliceFunction(
    pos=0.0673838*Ra^(1/3),
    neg=Buildings.Utilities.Math.Functions.spliceFunction(
      pos=0.028154*Ra^(0.4134),
      neg=1 + 1.7596678E-10*Ra^(2.2984755),
      x=Ra - 1E4,
      deltax=deltaRa),
    x=Ra - 5E4,
    deltax=deltaRa);
  /*
  if ( Ra <= 1E4) then
    Nu_1 = 1 + 1.7596678E-10*Ra^(2.2984755);
  elseif ( Ra <= 5E4) then
    Nu_1 = 0.028154*Ra^(0.4134);
  else
    Nu_1 = 0.0673838*Ra^(1/3);
  end if;
  */
  Nu_2 :=0.242*(Ra/(h/gas.x))^(0.272);
  Nu :=Buildings.Utilities.Math.Functions.smoothMax(
    x1=Nu_1,
    x2=Nu_2,
    deltaX=deltaNu);
  hCon :=Nu*Buildings.HeatTransfer.Data.Gases.thermalConductivity(gas, T_m)/gas.x;
  q_flow :=hCon*dT;
end convectionVerticalCavity;

Buildings.HeatTransfer.Windows.BaseClasses.convectionHorizontalCavity

Information

Function for convective heat transfer in horizontal window cavity. The computation is according to TARCOG 2006, except that this implementation computes the convection coefficient as a function that is differentiable in the temperatures.

References

TARCOG 2006: Carli, Inc., TARCOG: Mathematical models for calculation of thermal performance of glazing systems with our without shading devices, Technical Report, Oct. 17, 2006.

Inputs

Type	Name	Default	Description
Generic	gas		Thermophysical properties of gas fill
Real	Ra		Raleigh number
Temperature	T_m		Temperature used for thermophysical properties [K]
TemperatureDifference	dT		Temperature difference used to compute q_flow = h*dT [K]
Angle	til		Window tilt [rad]
Real	sinTil		Sine of window tilt
Real	cosTil		Cosine of the window tilt
Area	h	1.5	Height of window [m2]
Real	deltaNu	0.1	Small value for Nusselt number, used for smoothing
Real	deltaRa	1E3	Small value for Raleigh number, used for smoothing

Outputs

Type	Name	Description
Real	Nu	Nusselt number
CoefficientOfHeatTransfer	hCon	Convective heat transfer coefficient [W/(m2.K)]
HeatFlux	q_flow	Convective heat flux [W/m2]

Modelica definition

function convectionHorizontalCavity 
  "Free convection in horizontal cavity"
  input Buildings.HeatTransfer.Data.Gases.Generic gas 
    "Thermophysical properties of gas fill";
  input Real Ra(min=0) "Raleigh number";
  input Modelica.SIunits.Temperature T_m 
    "Temperature used for thermophysical properties";
  input Modelica.SIunits.TemperatureDifference dT 
    "Temperature difference used to compute q_flow = h*dT";
  input Modelica.SIunits.Angle til "Window tilt";
  input Real sinTil "Sine of window tilt";
  input Real cosTil "Cosine of the window tilt";
  input Modelica.SIunits.Area h(min=0) = 1.5 "Height of window";
  input Real deltaNu(min=0.01) = 0.1 
    "Small value for Nusselt number, used for smoothing";
  input Real deltaRa(min=0.01) = 1E3 
    "Small value for Raleigh number, used for smoothing";
  output Real Nu(min=0) "Nusselt number";
  output Modelica.SIunits.CoefficientOfHeatTransfer hCon(min=0) 
    "Convective heat transfer coefficient";
  output Modelica.SIunits.HeatFlux q_flow "Convective heat flux";
protected 
  Real Nu_1(min=0) "Nusselt number";
  Real Nu_2(min=0) "Nusselt number";
  constant Real dx=0.1 "Half-width of interval used for smoothing";
algorithm 
  if cosTil > 0 then
  Nu :=Buildings.Utilities.Math.Functions.spliceFunction(
    pos=
      Buildings.HeatTransfer.Windows.BaseClasses.nusseltHorizontalCavityReduced(
      gas=gas,
      Ra=Ra,
      T_m=T_m,
      dT=dT,
      h=h,
      sinTil=sinTil,
      deltaNu=deltaNu,
      deltaRa=deltaRa),
    neg=
      Buildings.HeatTransfer.Windows.BaseClasses.nusseltHorizontalCavityEnhanced(
      gas=gas,
      Ra=Ra,
      T_m=T_m,
      dT=dT,
      til=til,
      cosTil=abs(cosTil)),
    x=dT+dx,
    deltax=dx);
  else
    Nu :=Buildings.Utilities.Math.Functions.spliceFunction(
    pos=
      Buildings.HeatTransfer.Windows.BaseClasses.nusseltHorizontalCavityEnhanced(
      gas=gas,
      Ra=Ra,
      T_m=T_m,
      dT=dT,
      til=til,
      cosTil=abs(cosTil)),
    neg=
      Buildings.HeatTransfer.Windows.BaseClasses.nusseltHorizontalCavityReduced(
      gas=gas,
      Ra=Ra,
      T_m=T_m,
      dT=dT,
      h=h,
      sinTil=sinTil,
      deltaNu=deltaNu,
      deltaRa=deltaRa),
    x=dT-dx,
    deltax=dx);
  end if;
  hCon :=Nu*Buildings.HeatTransfer.Data.Gases.thermalConductivity(gas, T_m)/gas.x;
  q_flow :=hCon*dT;
end convectionHorizontalCavity;

Buildings.HeatTransfer.Windows.BaseClasses.nusseltHorizontalCavityEnhanced

Information

Function for Nusselt number in horizontal window cavity. The computation is according to TARCOG 2006, except that this implementation computes the Nusselt number as a function that is differentiable in the temperatures.

References

TARCOG 2006: Carli, Inc., TARCOG: Mathematical models for calculation of thermal performance of glazing systems with our without shading devices, Technical Report, Oct. 17, 2006.

Inputs

Type	Name	Default	Description
Generic	gas		Thermophysical properties of gas fill
Real	Ra		Raleigh number
Temperature	T_m		Temperature used for thermophysical properties [K]
TemperatureDifference	dT		Temperature difference used to compute q_flow = h*dT [K]
Angle	til		Window tilt [rad]
Real	cosTil		Cosine of the window tilt

Outputs

Type	Name	Description
Real	Nu	Nusselt number

Modelica definition

function nusseltHorizontalCavityEnhanced 
  "Nusselt number for horizontal cavity, bottom surface warmer than top surface"
  input Buildings.HeatTransfer.Data.Gases.Generic gas 
    "Thermophysical properties of gas fill";
  input Real Ra(min=0) "Raleigh number";
  input Modelica.SIunits.Temperature T_m 
    "Temperature used for thermophysical properties";
  input Modelica.SIunits.TemperatureDifference dT 
    "Temperature difference used to compute q_flow = h*dT";
  input Modelica.SIunits.Angle til "Window tilt";
  input Real cosTil(min=0) "Cosine of the window tilt";
  output Real Nu(min=0) "Nusselt number";
protected 
  Real k1 "Auxiliary variable";
  Real k2 "Auxiliary variable";
  Real k11 "Auxiliary variable";
  Real k22 "Auxiliary variable";
algorithm 
  // Windows inclined from 0 to 60 deg (eqn. 3.1-42 to 3.1-43)
  k1 :=1 - 1708/Ra/cosTil;
  k2 :=(Ra*cosTil/5830)^(1/3) - 1;
  k11 :=(k1 + Buildings.Utilities.Math.Functions.smoothMax(
    x1=k1,
    x2=-k1,
    deltaX=1E-1))/2;
  k22 :=(k2 + Buildings.Utilities.Math.Functions.smoothMax(
    x1=k2,
    x2=-k2,
    deltaX=1E-1))/2;
  Nu :=1 + 1.44*k11*(1 - 1708*abs(Modelica.Math.sin(1.8*til*180/Modelica.Constants.pi))
    ^(1.6)/Ra/cosTil) + k22;
end nusseltHorizontalCavityEnhanced;

Buildings.HeatTransfer.Windows.BaseClasses.nusseltHorizontalCavityReduced

Information

Function for Nusselt number in horizontal window cavity. The computation is according to TARCOG 2006, except that this implementation computes the Nusselt number as a function that is differentiable in the temperatures.

References

TARCOG 2006: Carli, Inc., TARCOG: Mathematical models for calculation of thermal performance of glazing systems with our without shading devices, Technical Report, Oct. 17, 2006.

Inputs

Type	Name	Default	Description
Generic	gas		Thermophysical properties of gas fill
Real	Ra		Raleigh number
Temperature	T_m		Temperature used for thermophysical properties [K]
TemperatureDifference	dT		Temperature difference used to compute q_flow = h*dT [K]
Area	h	1.5	Height of window [m2]
Real	sinTil		Sine of window tilt
Real	deltaNu	0.1	Small value for Nusselt number, used for smoothing
Real	deltaRa	1E3	Small value for Raleigh number, used for smoothing

Outputs

Type	Name	Description
Real	Nu	Nusselt number

Modelica definition

function nusseltHorizontalCavityReduced 
  "Nusselt number for horizontal cavity, bottom surface colder than top surface"
  input Buildings.HeatTransfer.Data.Gases.Generic gas 
    "Thermophysical properties of gas fill";
  input Real Ra(min=0) "Raleigh number";
  input Modelica.SIunits.Temperature T_m 
    "Temperature used for thermophysical properties";
  input Modelica.SIunits.TemperatureDifference dT 
    "Temperature difference used to compute q_flow = h*dT";
  input Modelica.SIunits.Area h(min=0) = 1.5 "Height of window";
  input Real sinTil "Sine of window tilt";
  input Real deltaNu(min=0.01) = 0.1 
    "Small value for Nusselt number, used for smoothing";
  input Real deltaRa(min=0.01) = 1E3 
    "Small value for Raleigh number, used for smoothing";
  output Real Nu(min=0) "Nusselt number";
protected 
  Real NuVer(min=0) "Nusselt number for vertical window";
algorithm 
  NuVer :=Buildings.HeatTransfer.Windows.BaseClasses.convectionVerticalCavity(
    gas=gas,
    Ra=Ra,
    T_m=T_m,
    dT=dT,
    h=h,
    deltaNu=deltaNu,
    deltaRa=deltaRa);
  Nu :=1 + (NuVer - 1)*sinTil;

end nusseltHorizontalCavityReduced;

Buildings.HeatTransfer.Windows.BaseClasses.smoothInterpolation

Information

Function to interpolate within a data array without triggerring events.

Inputs

Type	Name	Default	Description
Real	y[:]		Data array
Real	x		x value

Outputs

Type	Name	Description
Real	val	Return value

Modelica definition

function smoothInterpolation 
  "Get interpolated data without triggering events"
  input Real y[:] "Data array";
  input Real x "x value";
  output Real val "Return value";

protected 
  Integer k1;
  Integer k2;
  Real y1d;
  Real y2d;
algorithm 
  k1 := integer(x);
  k2 := k1 + 1;

  y1d := (y[k1 + 1] - y[k1 - 1])/2;
  y2d := (y[k2 + 1] - y[k2 - 1])/2;
  val := Modelica.Fluid.Utilities.cubicHermite(
    x,
    k1,
    k2,
    y[k1],
    y[k2],
    y1d,
    y2d);

end smoothInterpolation;