Buildings.Fluid.Storage
Package with thermal energy storage models
Information
This package contains thermal energy storage models.Extends from Modelica.Icons.VariantsPackage (Icon for package containing variants).
Package Content
| Name | Description |
|---|---|
 UsersGuide
|
User's Guide |
 ExpansionVessel
|
Expansion vessel with fixed pressure |
 Stratified
|
Model of a stratified tank for thermal energy storage |
 StratifiedEnhanced
|
Stratified tank model with enhanced discretization |
 StratifiedEnhancedInternalHex
|
A model of a water storage tank with a secondary loop and intenral heat exchanger |
 Examples
|
Collection of models that illustrate model use and test models |
| Validation
|
Collection of models that validate the storage models |
 BaseClasses
|
Package with base classes for Buildings.Fluid.Storage |
Buildings.Fluid.Storage.ExpansionVessel
Expansion vessel with fixed pressure
Information
This is a model of a pressure expansion vessel. The vessel has a constant pressure
that is equal to the value of the parameter p_start.
The model takes into account the energy and mass balance of the medium.
It has no heat exchange with the ambient.
The expansion vessel needs to be used in closed loops that contain water to set a reference pressure and, for liquids where the density is modeled as a function of temperature, to allow for the thermal expansion of the liquid.
Note that alternatively, the model Buildings.Fluid.Sources.Boundary_pT may be used to set a reference pressure. The main difference between these two models is that in this model, there is an energy and mass balance for the volume. In contrast, for Buildings.Fluid.Sources.Boundary_pT, any mass flow rate that flows out of the model will be at a user-specified temperature. Therefore, Buildings.Fluid.Sources.Boundary_pT leads to smaller systems of equations, which may result in faster simulation.
Extends from Buildings.Fluid.Interfaces.LumpedVolumeDeclarations (Declarations for lumped volumes).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| replaceable package Medium | PartialMedium | Medium in the component | |
| Volume | V_start | Volume of liquid stored in the vessel at the start of the simulation [m3] | |
| Pressure | p | Medium.p_default | Constant pressure of the expansion vessel [Pa] |
| Dynamics | |||
| Equations | |||
| Dynamics | energyDynamics | Modelica.Fluid.Types.Dynamic... | Type of energy balance: dynamic (3 initialization options) or steady state |
| Dynamics | massDynamics | Modelica.Fluid.Types.Dynamic... | Type of mass balance: dynamic (3 initialization options) or steady state |
| Real | mSenFac | 1 | Factor for scaling the sensible thermal mass of the volume |
| Initialization | |||
| AbsolutePressure | p_start | Medium.p_default | Start value of pressure [Pa] |
| Temperature | T_start | Medium.T_default | Start value of temperature [K] |
| MassFraction | X_start[Medium.nX] | Medium.X_default | Start value of mass fractions m_i/m [kg/kg] |
| ExtraProperty | C_start[Medium.nC] | fill(0, Medium.nC) | Start value of trace substances |
| ExtraProperty | C_nominal[Medium.nC] | fill(1E-2, Medium.nC) | Nominal value of trace substances. (Set to typical order of magnitude.) |
Connectors
| Type | Name | Description |
|---|---|---|
| FluidPort_a | port_a | Fluid port |
Modelica definition
model ExpansionVessel "Expansion vessel with fixed pressure"
extends Buildings.Fluid.Interfaces.LumpedVolumeDeclarations(
final energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
final massDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
final mSenFac=1);
parameter Modelica.SIunits.Volume V_start(start=1)
"Volume of liquid stored in the vessel at the start of the simulation";
parameter Modelica.SIunits.Pressure p = Medium.p_default
"Constant pressure of the expansion vessel";
Modelica.Fluid.Interfaces.FluidPort_a port_a(
redeclare package Medium = Medium) "Fluid port";
Modelica.SIunits.Mass m "Mass of liquid in the vessel";
protected
final parameter Medium.ThermodynamicState state_start = Medium.setState_pTX(
T=T_start,
p=p_start,
X=X_start[1:Medium.nXi]) "Medium state at start values";
final parameter Modelica.SIunits.Density rho_start=Medium.density(
state=state_start) "Density, used to compute start and guess values";
Modelica.SIunits.Energy H "Internal energy of fluid";
Modelica.SIunits.Mass[Medium.nXi] mXi
"Masses of independent components in the fluid";
Modelica.SIunits.Mass[Medium.nC] mC "Masses of trace substances in the fluid";
Medium.ExtraProperty C[Medium.nC](nominal=C_nominal)
"Trace substance mixture content";
initial equation
m = V_start * rho_start;
H = m*Medium.specificInternalEnergy(
Medium.setState_pTX(p=p_start, T=T_start, X= X_start[1:Medium.nXi]));
mXi = m*X_start[1:Medium.nXi];
mC = m*C_start[1:Medium.nC];
equation
assert(m > 1.0E-8,
"Expansion vessel is undersized. You need to increase the value of the parameter V_start.");
// Conservation equations
der(m) = port_a.m_flow;
der(H) = port_a.m_flow * actualStream(port_a.h_outflow);
der(mXi) = port_a.m_flow * actualStream(port_a.Xi_outflow);
der(mC) = port_a.m_flow * actualStream(port_a.C_outflow);
// Properties of outgoing flow.
// The port pressure is set to a constant value.
port_a.p = p_start;
m*port_a.h_outflow = H;
m*port_a.Xi_outflow = mXi;
m*port_a.C_outflow = mC;
end ExpansionVessel;
Buildings.Fluid.Storage.Stratified
Model of a stratified tank for thermal energy storage
Information
This is a model of a stratified storage tank.
See the Buildings.Fluid.Storage.UsersGuide for more information.
For a model with enhanced stratification, use Buildings.Fluid.Storage.StratifiedEnhanced.
Extends from Buildings.Fluid.Storage.BaseClasses.PartialStratified (Partial model of a stratified tank for thermal energy storage).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| replaceable package Medium | PartialMedium | Medium in the component | |
| Volume | VTan | Tank volume [m3] | |
| Length | hTan | Height of tank (without insulation) [m] | |
| Length | dIns | Thickness of insulation [m] | |
| ThermalConductivity | kIns | 0.04 | Specific heat conductivity of insulation [W/(m.K)] |
| Integer | nSeg | 2 | Number of volume segments |
| Time | tau | 1 | Time constant for mixing [s] |
| Nominal condition | |||
| MassFlowRate | m_flow_nominal | Nominal mass flow rate [kg/s] | |
| Assumptions | |||
| Boolean | allowFlowReversal | true | = false to simplify equations, assuming, but not enforcing, no flow reversal |
| Advanced | |||
| MassFlowRate | m_flow_small | 1E-4*abs(m_flow_nominal) | Small mass flow rate for regularization of zero flow [kg/s] |
| Diagnostics | |||
| Boolean | show_T | false | = true, if actual temperature at port is computed |
| Dynamics | |||
| Equations | |||
| Dynamics | energyDynamics | Modelica.Fluid.Types.Dynamic... | Formulation of energy balance |
| Dynamics | massDynamics | energyDynamics | Formulation of mass balance |
| Initialization | |||
| AbsolutePressure | p_start | Medium.p_default | Start value of pressure [Pa] |
| Temperature | T_start | Medium.T_default | Start value of temperature [K] |
| Temperature | TFlu_start[nSeg] | T_start*ones(nSeg) | Initial temperature of the tank segments, with TFlu_start[1] being the top segment [K] |
| MassFraction | X_start[Medium.nX] | Medium.X_default | Start value of mass fractions m_i/m [kg/kg] |
| ExtraProperty | C_start[Medium.nC] | fill(0, Medium.nC) | Start value of trace substances |
Connectors
| Type | Name | Description |
|---|---|---|
| FluidPort_a | port_a | Fluid connector a (positive design flow direction is from port_a to port_b) |
| FluidPort_b | port_b | Fluid connector b (positive design flow direction is from port_a to port_b) |
| output RealOutput | Ql_flow | Heat loss of tank (positive if heat flows from tank to ambient) |
| HeatPort_a | heaPorVol[nSeg] | Heat port that connects to the control volumes of the tank |
| HeatPort_a | heaPorSid | Heat port tank side (outside insulation) |
| HeatPort_a | heaPorTop | Heat port tank top (outside insulation) |
| HeatPort_a | heaPorBot | Heat port tank bottom (outside insulation). Leave unconnected for adiabatic condition |
| FluidPort_a | fluPorVol[nSeg] | Fluid port that connects to the control volumes of the tank |
Modelica definition
model Stratified "Model of a stratified tank for thermal energy storage"
extends Buildings.Fluid.Storage.BaseClasses.PartialStratified(vol(each nPorts=3));
Modelica.Fluid.Interfaces.FluidPort_a fluPorVol[nSeg](
redeclare each final package Medium = Medium)
"Fluid port that connects to the control volumes of the tank";
equation
connect(port_a, vol[1].ports[1]);
connect(vol[nSeg].ports[2], port_b);
for i in 1:(nSeg-1) loop
connect(vol[i].ports[2], vol[i + 1].ports[1]);
end for;
for i in 1:nSeg loop
connect(fluPorVol[i], vol[i].ports[3]);
end for;
end Stratified;
Buildings.Fluid.Storage.StratifiedEnhanced
Stratified tank model with enhanced discretization
Information
This is a model of a stratified storage tank for thermal energy storage.
See the Buildings.Fluid.Storage.UsersGuide for more information.
Limitations
The model requires at least 4 fluid segments. Hence, set nSeg to 4 or higher.
Extends from BaseClasses.PartialStratified (Partial model of a stratified tank for thermal energy storage).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| replaceable package Medium | PartialMedium | Medium in the component | |
| Volume | VTan | Tank volume [m3] | |
| Length | hTan | Height of tank (without insulation) [m] | |
| Length | dIns | Thickness of insulation [m] | |
| ThermalConductivity | kIns | 0.04 | Specific heat conductivity of insulation [W/(m.K)] |
| Integer | nSeg | 4 | Number of volume segments |
| Time | tau | 1 | Time constant for mixing [s] |
| Nominal condition | |||
| MassFlowRate | m_flow_nominal | Nominal mass flow rate [kg/s] | |
| Assumptions | |||
| Boolean | allowFlowReversal | true | = false to simplify equations, assuming, but not enforcing, no flow reversal |
| Advanced | |||
| MassFlowRate | m_flow_small | 1E-4*abs(m_flow_nominal) | Small mass flow rate for regularization of zero flow [kg/s] |
| Diagnostics | |||
| Boolean | show_T | false | = true, if actual temperature at port is computed |
| Dynamics | |||
| Equations | |||
| Dynamics | energyDynamics | Modelica.Fluid.Types.Dynamic... | Formulation of energy balance |
| Dynamics | massDynamics | energyDynamics | Formulation of mass balance |
| Initialization | |||
| AbsolutePressure | p_start | Medium.p_default | Start value of pressure [Pa] |
| Temperature | T_start | Medium.T_default | Start value of temperature [K] |
| Temperature | TFlu_start[nSeg] | T_start*ones(nSeg) | Initial temperature of the tank segments, with TFlu_start[1] being the top segment [K] |
| MassFraction | X_start[Medium.nX] | Medium.X_default | Start value of mass fractions m_i/m [kg/kg] |
| ExtraProperty | C_start[Medium.nC] | fill(0, Medium.nC) | Start value of trace substances |
Connectors
| Type | Name | Description |
|---|---|---|
| FluidPort_a | port_a | Fluid connector a (positive design flow direction is from port_a to port_b) |
| FluidPort_b | port_b | Fluid connector b (positive design flow direction is from port_a to port_b) |
| output RealOutput | Ql_flow | Heat loss of tank (positive if heat flows from tank to ambient) |
| HeatPort_a | heaPorVol[nSeg] | Heat port that connects to the control volumes of the tank |
| HeatPort_a | heaPorSid | Heat port tank side (outside insulation) |
| HeatPort_a | heaPorTop | Heat port tank top (outside insulation) |
| HeatPort_a | heaPorBot | Heat port tank bottom (outside insulation). Leave unconnected for adiabatic condition |
Modelica definition
model StratifiedEnhanced "Stratified tank model with enhanced discretization"
extends BaseClasses.PartialStratified(
nSeg=4,
vol(each prescribedHeatFlowRate=true,
each nPorts=3));
protected
Buildings.Fluid.Sensors.EnthalpyFlowRate H_a_flow(
redeclare package Medium = Medium,
final m_flow_nominal=m_flow_nominal,
final tau=0,
final allowFlowReversal=allowFlowReversal,
final m_flow_small=m_flow_small) "Enthalpy flow rate at port a";
Buildings.Fluid.Sensors.EnthalpyFlowRate[nSeg - 1] H_vol_flow(
redeclare package Medium = Medium,
each final m_flow_nominal=m_flow_nominal,
each final tau=0,
each final allowFlowReversal=allowFlowReversal,
each final m_flow_small=m_flow_small)
"Enthalpy flow rate between the volumes";
Buildings.Fluid.Sensors.EnthalpyFlowRate H_b_flow(
redeclare package Medium = Medium,
final m_flow_nominal=m_flow_nominal,
final tau=0,
final allowFlowReversal=allowFlowReversal,
final m_flow_small=m_flow_small) "Enthalpy flow rate at port b";
BaseClasses.ThirdOrderStratifier str(
redeclare package Medium = Medium,
nSeg=nSeg,
m_flow_small=m_flow_small) "Model to reduce numerical dissipation";
Modelica.Blocks.Sources.RealExpression mTan_flow(y=port_a.m_flow)
"Mass flow rate at port a";
equation
connect(H_a_flow.port_b, vol[1].ports[1]);
connect(vol[nSeg].ports[2], H_b_flow.port_a);
connect(H_b_flow.port_b, port_b);
for i in 1:(nSeg-1) loop
connect(vol[i].ports[2], H_vol_flow[i].port_a);
connect(H_vol_flow[i].port_b, vol[i + 1].ports[1]);
end for;
connect(port_a, H_a_flow.port_a);
connect(vol[1:nSeg].ports[3], str.fluidPort[2:nSeg+1]);
connect(H_a_flow.H_flow, str.H_flow[1]);
connect(H_vol_flow[1:nSeg-1].H_flow, str.H_flow[2:nSeg]);
connect(H_b_flow.H_flow, str.H_flow[nSeg + 1]);
connect(str.heatPort, vol.heatPort);
connect(port_a, str.fluidPort[1]);
connect(port_b, str.fluidPort[nSeg + 2]);
connect(mTan_flow.y, str.m_flow);
end StratifiedEnhanced;
Buildings.Fluid.Storage.StratifiedEnhancedInternalHex
A model of a water storage tank with a secondary loop and intenral heat exchanger
Information
This is a model of a stratified storage tank for thermal energy storage with built-in heat exchanger.
See the Buildings.Fluid.Storage.UsersGuide for more information.
Limitations
The model requires at least 4 fluid segments. Hence, set nSeg to 4 or higher.
Extends from StratifiedEnhanced (Stratified tank model with enhanced discretization).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| replaceable package Medium | PartialMedium | Medium in the component | |
| Volume | VTan | Tank volume [m3] | |
| Length | hTan | Height of tank (without insulation) [m] | |
| Length | dIns | Thickness of insulation [m] | |
| ThermalConductivity | kIns | 0.04 | Specific heat conductivity of insulation [W/(m.K)] |
| Integer | nSeg | 4 | Number of volume segments |
| Time | tau | 1 | Time constant for mixing [s] |
| Nominal condition | |||
| MassFlowRate | m_flow_nominal | Nominal mass flow rate [kg/s] | |
| Heat exchanger | |||
| replaceable package MediumHex | Modelica.Media.Interfaces.Pa... | Medium in the heat exchanger | |
| Height | hHex_a | Height of portHex_a of the heat exchanger, measured from tank bottom [m] | |
| Height | hHex_b | Height of portHex_b of the heat exchanger, measured from tank bottom [m] | |
| Integer | hexSegMult | 2 | Number of heat exchanger segments in each tank segment |
| Diameter | dExtHex | 0.025 | Exterior diameter of the heat exchanger pipe [m] |
| HeatFlowRate | Q_flow_nominal | Heat transfer at nominal conditions [W] | |
| Temperature | TTan_nominal | Temperature of fluid inside the tank at nominal heat transfer conditions [K] | |
| Temperature | THex_nominal | Temperature of fluid inside the heat exchanger at nominal heat transfer conditions [K] | |
| Real | r_nominal | 0.5 | Ratio between coil inside and outside convective heat transfer at nominal heat transfer conditions |
| MassFlowRate | mHex_flow_nominal | Nominal mass flow rate through the heat exchanger [kg/s] | |
| PressureDifference | dpHex_nominal | 2500 | Pressure drop across the heat exchanger at nominal conditions [Pa] |
| Assumptions | |||
| Boolean | allowFlowReversal | true | = false to simplify equations, assuming, but not enforcing, no flow reversal |
| Heat exchanger | |||
| Boolean | allowFlowReversalHex | true | = true to allow flow reversal in heat exchanger, false restricts to design direction (portHex_a -> portHex_b) |
| Advanced | |||
| MassFlowRate | m_flow_small | 1E-4*abs(m_flow_nominal) | Small mass flow rate for regularization of zero flow [kg/s] |
| Diagnostics | |||
| Boolean | show_T | false | = true, if actual temperature at port is computed |
| Dynamics | |||
| Equations | |||
| Dynamics | energyDynamics | Modelica.Fluid.Types.Dynamic... | Formulation of energy balance |
| Dynamics | massDynamics | energyDynamics | Formulation of mass balance |
| Initialization | |||
| AbsolutePressure | p_start | Medium.p_default | Start value of pressure [Pa] |
| Temperature | T_start | Medium.T_default | Start value of temperature [K] |
| Temperature | TFlu_start[nSeg] | T_start*ones(nSeg) | Initial temperature of the tank segments, with TFlu_start[1] being the top segment [K] |
| MassFraction | X_start[Medium.nX] | Medium.X_default | Start value of mass fractions m_i/m [kg/kg] |
| ExtraProperty | C_start[Medium.nC] | fill(0, Medium.nC) | Start value of trace substances |
| Flow resistance heat exchanger | |||
| Boolean | computeFlowResistance | true | =true, compute flow resistance. Set to false to assume no friction |
| Boolean | from_dp | false | = true, use m_flow = f(dp) else dp = f(m_flow) |
| Boolean | linearizeFlowResistance | false | = true, use linear relation between m_flow and dp for any flow rate |
| Real | deltaM | 0.1 | Fraction of nominal flow rate where flow transitions to laminar |
| Dynamics heat exchanger | |||
| Equations | |||
| Dynamics | energyDynamicsHex | Modelica.Fluid.Types.Dynamic... | Formulation of energy balance for heat exchanger internal fluid mass |
| Dynamics | massDynamicsHex | energyDynamicsHex | Formulation of mass balance for heat exchanger |
| Dynamics | energyDynamicsHexSolid | energyDynamicsHex | Formulation of energy balance for heat exchanger solid mass |
| Length | lHex | rTan*abs(segHex_a - segHex_b... | Approximate length of the heat exchanger [m] |
| Area | ACroHex | (dExtHex^2 - (0.8*dExtHex)^2... | Cross sectional area of the heat exchanger [m2] |
| SpecificHeatCapacity | cHex | 490 | Specific heat capacity of the heat exchanger material [J/(kg.K)] |
| Density | dHex | 8000 | Density of the heat exchanger material [kg/m3] |
| HeatCapacity | CHex | ACroHex*lHex*dHex*cHex | Capacitance of the heat exchanger without the fluid [J/K] |
Connectors
| Type | Name | Description |
|---|---|---|
| FluidPort_a | port_a | Fluid connector a (positive design flow direction is from port_a to port_b) |
| FluidPort_b | port_b | Fluid connector b (positive design flow direction is from port_a to port_b) |
| output RealOutput | Ql_flow | Heat loss of tank (positive if heat flows from tank to ambient) |
| HeatPort_a | heaPorVol[nSeg] | Heat port that connects to the control volumes of the tank |
| HeatPort_a | heaPorSid | Heat port tank side (outside insulation) |
| HeatPort_a | heaPorTop | Heat port tank top (outside insulation) |
| HeatPort_a | heaPorBot | Heat port tank bottom (outside insulation). Leave unconnected for adiabatic condition |
| FluidPort_a | portHex_a | Heat exchanger inlet |
| FluidPort_b | portHex_b | Heat exchanger outlet |
| Heat exchanger | ||
| replaceable package MediumHex | Medium in the heat exchanger | |
Modelica definition
model StratifiedEnhancedInternalHex
"A model of a water storage tank with a secondary loop and intenral heat exchanger"
extends StratifiedEnhanced;
replaceable package MediumHex =
Modelica.Media.Interfaces.PartialMedium "Medium in the heat exchanger";
parameter Modelica.SIunits.Height hHex_a
"Height of portHex_a of the heat exchanger, measured from tank bottom";
parameter Modelica.SIunits.Height hHex_b
"Height of portHex_b of the heat exchanger, measured from tank bottom";
parameter Integer hexSegMult(min=1) = 2
"Number of heat exchanger segments in each tank segment";
parameter Modelica.SIunits.Diameter dExtHex = 0.025
"Exterior diameter of the heat exchanger pipe";
parameter Modelica.SIunits.HeatFlowRate Q_flow_nominal
"Heat transfer at nominal conditions";
parameter Modelica.SIunits.Temperature TTan_nominal
"Temperature of fluid inside the tank at nominal heat transfer conditions";
parameter Modelica.SIunits.Temperature THex_nominal
"Temperature of fluid inside the heat exchanger at nominal heat transfer conditions";
parameter Real r_nominal(min=0, max=1)=0.5
"Ratio between coil inside and outside convective heat transfer at nominal heat transfer conditions";
parameter Modelica.SIunits.MassFlowRate mHex_flow_nominal
"Nominal mass flow rate through the heat exchanger";
parameter Modelica.SIunits.PressureDifference dpHex_nominal(displayUnit="Pa") = 2500
"Pressure drop across the heat exchanger at nominal conditions";
parameter Boolean computeFlowResistance=true
"=true, compute flow resistance. Set to false to assume no friction";
parameter Boolean from_dp=false
"= true, use m_flow = f(dp) else dp = f(m_flow)";
parameter Boolean linearizeFlowResistance=false
"= true, use linear relation between m_flow and dp for any flow rate";
parameter Real deltaM=0.1
"Fraction of nominal flow rate where flow transitions to laminar";
parameter Modelica.Fluid.Types.Dynamics energyDynamicsHex=
Modelica.Fluid.Types.Dynamics.DynamicFreeInitial
"Formulation of energy balance for heat exchanger internal fluid mass";
parameter Modelica.Fluid.Types.Dynamics massDynamicsHex=
energyDynamicsHex "Formulation of mass balance for heat exchanger";
parameter Modelica.Fluid.Types.Dynamics energyDynamicsHexSolid=energyDynamicsHex
"Formulation of energy balance for heat exchanger solid mass";
parameter Modelica.SIunits.Length lHex=
rTan*abs(segHex_a-segHex_b)*Modelica.Constants.pi
"Approximate length of the heat exchanger";
parameter Modelica.SIunits.Area ACroHex=
(dExtHex^2-(0.8*dExtHex)^2)*Modelica.Constants.pi/4
"Cross sectional area of the heat exchanger";
parameter Modelica.SIunits.SpecificHeatCapacity cHex=490
"Specific heat capacity of the heat exchanger material";
parameter Modelica.SIunits.Density dHex=8000
"Density of the heat exchanger material";
parameter Modelica.SIunits.HeatCapacity CHex=
ACroHex*lHex*dHex*cHex
"Capacitance of the heat exchanger without the fluid";
parameter Boolean allowFlowReversalHex = true
"= true to allow flow reversal in heat exchanger, false restricts to design direction (portHex_a -> portHex_b)";
Modelica.Fluid.Interfaces.FluidPort_a portHex_a(
redeclare final package Medium =MediumHex,
m_flow(min=if allowFlowReversalHex then -Modelica.Constants.inf else 0))
"Heat exchanger inlet";
Modelica.Fluid.Interfaces.FluidPort_b portHex_b(
redeclare final package Medium = MediumHex,
m_flow(max=if allowFlowReversalHex then Modelica.Constants.inf else 0))
"Heat exchanger outlet";
BaseClasses.IndirectTankHeatExchanger indTanHex(
redeclare final package MediumTan = Medium,
redeclare final package MediumHex = MediumHex,
final nSeg=nSegHex,
final CHex=CHex,
final volHexFlu=volHexFlu,
final Q_flow_nominal=Q_flow_nominal,
final TTan_nominal=TTan_nominal,
final THex_nominal=THex_nominal,
final r_nominal=r_nominal,
final dExtHex=dExtHex,
final dp_nominal=dpHex_nominal,
final m_flow_nominal=mHex_flow_nominal,
final energyDynamics=energyDynamicsHex,
final energyDynamicsSolid=energyDynamicsHexSolid,
final massDynamics=massDynamicsHex,
final computeFlowResistance=computeFlowResistance,
from_dp=from_dp,
final linearizeFlowResistance=linearizeFlowResistance,
final deltaM=deltaM,
final allowFlowReversal=allowFlowReversalHex,
final m_flow_small=1e-4*abs(mHex_flow_nominal))
"Heat exchanger inside the tank";
Modelica.SIunits.HeatFlowRate QHex_flow = -sum(indTanHex.port.Q_flow)
"Heat transferred from the heat exchanger to the tank";
protected
final parameter Integer segHex_a = nSeg-integer(hHex_a/segHeight)
"Tank segment in which port a1 of the heat exchanger is located in";
final parameter Integer segHex_b = nSeg-integer(hHex_b/segHeight)
"Tank segment in which port b1 of the heat exchanger is located in";
final parameter Modelica.SIunits.Height segHeight = hTan/nSeg
"Height of each tank segment (relative to bottom of same segment)";
final parameter Modelica.SIunits.Length dHHex = abs(hHex_a-hHex_b)
"Vertical distance between the heat exchanger inlet and outlet";
final parameter Modelica.SIunits.Volume volHexFlu=
Modelica.Constants.pi * (0.8*dExtHex)^2/4 *lHex
"Volume of the heat exchanger";
final parameter Integer nSegHexTan=
if segHex_a > segHex_b then segHex_a-segHex_b + 1 else segHex_b-segHex_a + 1
"Number of tank segments the heat exchanger resides in";
final parameter Integer nSegHex = nSegHexTan*hexSegMult
"Number of heat exchanger segments";
initial equation
assert(hHex_a >= 0 and hHex_a <= hTan,
"The parameter hHex_a is outside its valid range.");
assert(hHex_b >= 0 and hHex_b <= hTan,
"The parameter hHex_b is outside its valid range.");
assert(dHHex > 0,
"The parameters hHex_a and hHex_b must not be equal.");
equation
for j in 0:nSegHexTan-1 loop
for i in 1:hexSegMult loop
connect(indTanHex.port[j*hexSegMult+i], heaPorVol[segHex_a + (if hHex_a > hHex_b then j else -j)]);
end for;
end for;
connect(portHex_a, indTanHex.port_a);
connect(indTanHex.port_b, portHex_b);
end StratifiedEnhancedInternalHex;