Buildings.Fluid.FMI.BaseClasses

Package with base classes for Buildings.Fluid.FMI

Information

This package contains base classes that are used to construct the models in Buildings.Fluid.FMI.

Extends from Modelica.Icons.BasesPackage (Icon for packages containing base classes).

Package Content

Name	Description
X_w_toX	Conversion from Xi to X
hOut_toT	Conversion from h to T

Buildings.Fluid.FMI.BaseClasses.X_w_toX

Conversion from Xi to X

Buildings.Fluid.FMI.BaseClasses.X_w_toX

Information

Block that converts a scalar input for the water mass fraction Xi to a vector output X. This is needed for models in which a scalar input signal Xi that may be conditionally removed is to be connected to a model with a vector input X, because the conversion from scalar to vector needs to access the conditional connector, but conditional connectors can only be used in connect statements.

Extends from Modelica.Blocks.Icons.Block (Basic graphical layout of input/output block).

Parameters

Type	Name	Default	Description
replaceable package Medium		Modelica.Media.Interfaces.Pa...	Medium in the component

Connectors

Type	Name	Description
replaceable package Medium		Medium in the component
input RealInput	X_w	Water mass fraction per total air mass [kg/kg]
output RealOutput	X[Medium.nX]	Prescribed fluid composition [kg/kg]

Modelica definition

block X_w_toX "Conversion from Xi to X" extends Modelica.Blocks.Icons.Block; replaceable package Medium = Modelica.Media.Interfaces.PartialMedium "Medium in the component"; Modelica.Blocks.Interfaces.RealInput X_w(final unit="kg/kg") if Medium.nXi > 0 "Water mass fraction per total air mass"; Modelica.Blocks.Interfaces.RealOutput X[Medium.nX]( each final unit="kg/kg", final quantity=Medium.substanceNames) "Prescribed fluid composition"; protected Modelica.Blocks.Interfaces.RealInput X_w_internal(final unit="kg/kg") "Internal connector for water mass fraction per total air mass"; equation // Conditional connector connect(X_w_internal, X_w); if Medium.nXi == 0 then X_w_internal = 0; end if; // Assign vector to output connector X = if Medium.nX == 1 then ones(Medium.nX) else cat(1, {X_w_internal}, {1-X_w_internal}); end X_w_toX;

Buildings.Fluid.FMI.BaseClasses.hOut_toT

Conversion from h to T

Buildings.Fluid.FMI.BaseClasses.hOut_toT

Information

Block that converts enthalpy to temperature.

Extends from Modelica.Blocks.Icons.Block (Basic graphical layout of input/output block).

Parameters

Type	Name	Default	Description
replaceable package Medium		Modelica.Media.Interfaces.Pa...	Medium in the component

Connectors

Type	Name	Description
replaceable package Medium		Medium in the component
input RealInput	h	Specific enthalpy [J/kg]
input RealInput	Xi[Medium.nXi]	Water vapor concentration in kg/kg total air [kg/kg]
output RealOutput	T	Temperature [K]

Modelica definition

block hOut_toT "Conversion from h to T" extends Modelica.Blocks.Icons.Block; replaceable package Medium = Modelica.Media.Interfaces.PartialMedium "Medium in the component"; Modelica.Blocks.Interfaces.RealInput h(final unit="J/kg") "Specific enthalpy"; Modelica.Blocks.Interfaces.RealInput Xi[Medium.nXi](each final unit="kg/kg") if Medium.nXi > 0 "Water vapor concentration in kg/kg total air"; Modelica.Blocks.Interfaces.RealOutput T(final unit="K", displayUnit="degC") "Temperature"; protected Modelica.Blocks.Interfaces.RealInput Xi_internal[Medium.nXi]( each final unit = "kg/kg") "Internal connector for water vapor concentration in kg/kg total air"; equation // Conditional connectors connect(Xi_internal, Xi); if Medium.nXi == 0 then Xi_internal = zeros(Medium.nXi); end if; T = Medium.temperature_phX( p=Medium.p_default, h=h, X=Xi_internal); end hOut_toT;