Buildings.HeatTransfer.Examples

Collection of models that illustrate model use and test models

Information

This package contains examples for the use of models that can be found in Buildings.HeatTransfer.

Extends from Modelica.Icons.ExamplesPackage (Icon for packages containing runnable examples).

Package Content

Name Description
Buildings.HeatTransfer.Examples.ConductorInitialization ConductorInitialization Test model for heat conductor initialization
Buildings.HeatTransfer.Examples.ConductorMultiLayer ConductorMultiLayer Test model for heat conductor
Buildings.HeatTransfer.Examples.ConductorMultiLayer2 ConductorMultiLayer2 Test model for multi layer heat conductor with one state added at the surface a of the construction
Buildings.HeatTransfer.Examples.ConductorMultiLayer3 ConductorMultiLayer3 Test model for multi layer heat conductor with one state added at the surfaces a and b of the construction
Buildings.HeatTransfer.Examples.ConductorSingleLayer ConductorSingleLayer Test model for heat conductor
Buildings.HeatTransfer.Examples.ConductorSingleLayer2 ConductorSingleLayer2 Test model for single layer heat conductor without states added at the surfaces of the construction
Buildings.HeatTransfer.Examples.ConductorSingleLayerCylinder ConductorSingleLayerCylinder Test model for heat conduction in a cylinder
Buildings.HeatTransfer.Examples.ConductorSingleLayerPCM ConductorSingleLayerPCM Test model for heat conductor
Buildings.HeatTransfer.Examples.ConductorSteadyStateTransient ConductorSteadyStateTransient Test model for heat conductor
Buildings.HeatTransfer.Examples.ConductorStepResponse ConductorStepResponse Test model for heat conductor

Buildings.HeatTransfer.Examples.ConductorInitialization Buildings.HeatTransfer.Examples.ConductorInitialization

Test model for heat conductor initialization

Buildings.HeatTransfer.Examples.ConductorInitialization

Information

This example illustrates how to initialize heat conductors in steady state and with predefined temperatures.

Extends from Modelica.Icons.Example (Icon for runnable examples).

Parameters

TypeNameDefaultDescription
Brickbrickbrick(x=0.18, nStaRef=3, nSt... 
InsulationBoardinsulationinsulation(x=0.05, nStaRef=2... 
GenericcompositeWallcompositeWall(material={insu...Composite wall consisting of insulation and material

Modelica definition

model ConductorInitialization "Test model for heat conductor initialization" extends Modelica.Icons.Example; Buildings.HeatTransfer.Sources.FixedTemperature TB(T=303.15); Buildings.HeatTransfer.Sources.PrescribedTemperature TA; parameter Buildings.HeatTransfer.Data.Solids.Brick brick(x=0.18, nStaRef=3, nSta=5); parameter Buildings.HeatTransfer.Data.Solids.InsulationBoard insulation(x=0.05, nStaRef=2, nSta=5); parameter Buildings.HeatTransfer.Data.OpaqueConstructions.Generic compositeWall( material={insulation,brick}, nLay=2) "Composite wall consisting of insulation and material"; Buildings.HeatTransfer.Conduction.MultiLayer conS1( A=2, steadyStateInitial=true, layers=compositeWall, stateAtSurface_a=false, stateAtSurface_b=false); Modelica.Blocks.Sources.Step step( height=10, offset=283.15, startTime=43200); equation connect(step.y, TA.T); connect(conS1.port_b, TB.port); connect(TA.port, conS1.port_a); end ConductorInitialization;

Buildings.HeatTransfer.Examples.ConductorMultiLayer Buildings.HeatTransfer.Examples.ConductorMultiLayer

Test model for heat conductor

Buildings.HeatTransfer.Examples.ConductorMultiLayer

Information

This example illustrates how to use a solid material, set its heat capacity to zero, and then use this material in a multi-layer construction. The plot window shows that the insulation is computed in steady state, where as the brick is computed using transient heat conduction.

Extends from Modelica.Icons.Example (Icon for runnable examples).

Modelica definition

model ConductorMultiLayer "Test model for heat conductor" extends Modelica.Icons.Example; Buildings.HeatTransfer.Sources.FixedTemperature TB(T=293.15); Buildings.HeatTransfer.Sources.PrescribedTemperature TA; Modelica.Blocks.Sources.Step step( height=10, offset=293.15, startTime=43200); Buildings.HeatTransfer.Conduction.MultiLayer con( steadyStateInitial=false, redeclare Buildings.HeatTransfer.Data.OpaqueConstructions.Insulation100Concrete200 layers, A=0.1, stateAtSurface_b=false); Buildings.HeatTransfer.Convection.Interior conv( A=0.1, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; equation connect(step.y, TA.T); connect(con.port_b, TB.port); connect(conv.fluid, TA.port); connect(conv.solid, con.port_a); end ConductorMultiLayer;

Buildings.HeatTransfer.Examples.ConductorMultiLayer2 Buildings.HeatTransfer.Examples.ConductorMultiLayer2

Test model for multi layer heat conductor with one state added at the surface a of the construction

Buildings.HeatTransfer.Examples.ConductorMultiLayer2

Information

This example is similar to Buildings.HeatTransfer.Examples.ConductorMultiLayer. The main difference is that a state is added at the surface a of the construction.

Extends from ConductorMultiLayer (Test model for heat conductor).

Modelica definition

model ConductorMultiLayer2 "Test model for multi layer heat conductor with one state added at the surface a of the construction" extends ConductorMultiLayer; end ConductorMultiLayer2;

Buildings.HeatTransfer.Examples.ConductorMultiLayer3 Buildings.HeatTransfer.Examples.ConductorMultiLayer3

Test model for multi layer heat conductor with one state added at the surfaces a and b of the construction

Buildings.HeatTransfer.Examples.ConductorMultiLayer3

Information

This example is similar to Buildings.HeatTransfer.Examples.ConductorMultiLayer. The main difference is that a state is added at the surfaces a and b of the construction.

Extends from ConductorMultiLayer (Test model for heat conductor).

Modelica definition

model ConductorMultiLayer3 "Test model for multi layer heat conductor with one state added at the surfaces a and b of the construction" extends ConductorMultiLayer; end ConductorMultiLayer3;

Buildings.HeatTransfer.Examples.ConductorSingleLayer Buildings.HeatTransfer.Examples.ConductorSingleLayer

Test model for heat conductor

Buildings.HeatTransfer.Examples.ConductorSingleLayer

Information

This example tests if two conductors in series computes the same heat transfer as one conductor with twice the thickness.

Extends from Modelica.Icons.Example (Icon for runnable examples).

Parameters

TypeNameDefaultDescription
Concreteconcrete200concrete200(x=0.2, nSta=4) 
Concreteconcrete100concrete100(x=0.1, nSta=2) 

Modelica definition

model ConductorSingleLayer "Test model for heat conductor" extends Modelica.Icons.Example; Buildings.HeatTransfer.Conduction.SingleLayer con(A=1, material=concrete200, stateAtSurface_b=true); Buildings.HeatTransfer.Sources.FixedTemperature TB(T=293.15); Buildings.HeatTransfer.Sources.PrescribedTemperature TA; Modelica.Blocks.Sources.Step step( height=10, offset=293.15, startTime=3600); Buildings.HeatTransfer.Conduction.SingleLayer con1( A=1, material=concrete100, stateAtSurface_b=false); Buildings.HeatTransfer.Sources.FixedTemperature TB1( T=293.15); Buildings.HeatTransfer.Sources.PrescribedTemperature TA1; Buildings.HeatTransfer.Conduction.SingleLayer con2( A=1, material=concrete100, stateAtSurface_a=false, stateAtSurface_b=true); Modelica.Thermal.HeatTransfer.Sensors.HeatFlowSensor heaFlo2; Modelica.Thermal.HeatTransfer.Sensors.HeatFlowSensor heaFlo1; parameter Buildings.HeatTransfer.Data.Solids.Concrete concrete200(x=0.2, nSta=4); parameter Buildings.HeatTransfer.Data.Solids.Concrete concrete100(x=0.1, nSta=2); Buildings.HeatTransfer.Convection.Interior conv1( A=1, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; Buildings.HeatTransfer.Convection.Interior conv2( A=1, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; Modelica.Blocks.Math.Add cheEqu(k2=-1) "Checks for equality of the results"; equation connect(con.port_b, TB.port); connect(step.y, TA.T); connect(step.y, TA1.T); connect(con1.port_b, con2.port_a); connect(con2.port_b, TB1.port); connect(heaFlo2.port_b, con1.port_a); connect(heaFlo1.port_b, con.port_a); connect(TA.port, conv1.fluid); connect(TA1.port, conv2.fluid); connect(conv2.solid, heaFlo2.port_a); connect(conv1.solid, heaFlo1.port_a); connect(heaFlo1.Q_flow, cheEqu.u1); connect(heaFlo2.Q_flow, cheEqu.u2); end ConductorSingleLayer;

Buildings.HeatTransfer.Examples.ConductorSingleLayer2 Buildings.HeatTransfer.Examples.ConductorSingleLayer2

Test model for single layer heat conductor without states added at the surfaces of the construction

Buildings.HeatTransfer.Examples.ConductorSingleLayer2

Information

This example is similar to Buildings.HeatTransfer.Examples.ConductorSingleLayer. The main difference is that there are no states at the surfaces of the construction.

Extends from ConductorSingleLayer (Test model for heat conductor).

Parameters

TypeNameDefaultDescription
Concreteconcrete200  
Concreteconcrete100  

Modelica definition

model ConductorSingleLayer2 "Test model for single layer heat conductor without states added at the surfaces of the construction" extends ConductorSingleLayer( con(stateAtSurface_a=false, stateAtSurface_b=false), con1(stateAtSurface_a=false, stateAtSurface_b=false), con2(stateAtSurface_a=false, stateAtSurface_b=false)); end ConductorSingleLayer2;

Buildings.HeatTransfer.Examples.ConductorSingleLayerCylinder Buildings.HeatTransfer.Examples.ConductorSingleLayerCylinder

Test model for heat conduction in a cylinder

Buildings.HeatTransfer.Examples.ConductorSingleLayerCylinder

Information

This example tests a circular conductor with a constant temperature at his boundary.

Extends from Modelica.Icons.Example (Icon for runnable examples).

Parameters

TypeNameDefaultDescription
HeatFlowRateQ_flow50[W]
Concreteconcrete  

Modelica definition

model ConductorSingleLayerCylinder "Test model for heat conduction in a cylinder" extends Modelica.Icons.Example; parameter Modelica.SIunits.HeatFlowRate Q_flow=50; Buildings.HeatTransfer.Conduction.SingleLayerCylinder con( material=concrete, steadyStateInitial=false, final nSta=8, r_a=0.1, r_b=3, h=10, TInt_start=293.15, TExt_start=293.15); Buildings.HeatTransfer.Sources.PrescribedHeatFlow Qa; parameter Buildings.HeatTransfer.Data.Soil.Concrete concrete; Modelica.Blocks.Sources.Step step( offset=0, height=Q_flow, startTime=3600); Buildings.HeatTransfer.Sources.FixedTemperature TBou(T=293.15) "Boundary condition"; equation connect(Qa.port, con.port_a); connect(step.y, Qa.Q_flow); connect(TBou.port, con.port_b); end ConductorSingleLayerCylinder;

Buildings.HeatTransfer.Examples.ConductorSingleLayerPCM Buildings.HeatTransfer.Examples.ConductorSingleLayerPCM

Test model for heat conductor

Buildings.HeatTransfer.Examples.ConductorSingleLayerPCM

Information

This example tests the implementation of the phase-change material (PCM) model.

The phase-change material matPCM is exposed to the same boundary conditions as the non phase-change material. In the construction conPCM2, the phase change is around 20.5 °C. In the construction conPCM, the phase change is around 40.5 °C, which is above the temperature range simulated in this model. Therefore, the same result is expected for the PCM material conPCM as is for two conductors in series. Note that in case of using matPCM, the internal energy is the dependent variable, whereas in case of two conductors in series, the temperature is the dependent variable. However, both models will produce the same results.

The cheEqu block computes the difference between the heat fluxes, which should be equal except for the numerical approximation error of the solver.

Extends from Modelica.Icons.Example (Icon for runnable examples).

Parameters

TypeNameDefaultDescription
Concreteconcrete100concrete100(x=0.1, nStaRef=4)Non-PCM material
GenericmatPCMmatPCM(x=0.2, k=1.4, c=840, ...PCM material with phase change near 40 degC
GenericmatPCM2matPCM2(x=0.2, k=1.4, c=840,...PCM material with phase change near room temperature

Modelica definition

model ConductorSingleLayerPCM "Test model for heat conductor" extends Modelica.Icons.Example; Buildings.HeatTransfer.Sources.PrescribedTemperature TA "Temperature boundary condition"; Modelica.Blocks.Sources.Step step( height=10, offset=293.15, startTime=360); Buildings.HeatTransfer.Sources.PrescribedTemperature TA1 "Temperature boundary condition"; Modelica.Thermal.HeatTransfer.Sensors.HeatFlowSensor heaFlo2 "Heat flow sensor"; Modelica.Thermal.HeatTransfer.Sensors.HeatFlowSensor heaFlo1 "Heat flow sensor"; Modelica.Blocks.Math.Add cheEqu(k2=-1) "Checks for equality of the results"; parameter Buildings.HeatTransfer.Data.Solids.Concrete concrete100(x=0.1, nStaRef=4) "Non-PCM material"; Buildings.HeatTransfer.Convection.Interior conv1( A=1, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; Buildings.HeatTransfer.Convection.Interior conv2( A=1, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; Buildings.HeatTransfer.Conduction.SingleLayer conPCM( A=1, material=matPCM, stateAtSurface_b=true) "Construction with phase change around 40 degC"; Buildings.HeatTransfer.Conduction.SingleLayer con1( A=1, material=concrete100, stateAtSurface_b=false) "Construction without PCM"; Buildings.HeatTransfer.Conduction.SingleLayer con2( A=1, material=concrete100, stateAtSurface_a=false, stateAtSurface_b=true) "Construction without PCM"; parameter Buildings.HeatTransfer.Data.SolidsPCM.Generic matPCM( x=0.2, k=1.4, c=840, d=2240, nSta=4, TSol=273.15 + 40.49, TLiq=273.15 + 40.51, LHea=100000) "PCM material with phase change near 40 degC"; Buildings.HeatTransfer.Sources.PrescribedTemperature TA2 "Temperature boundary condition"; Buildings.HeatTransfer.Convection.Interior conv3( A=1, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; Buildings.HeatTransfer.Conduction.SingleLayer conPCM2( A=1, material=matPCM2, stateAtSurface_b=false) "Construction with phase change near room temperature"; parameter Buildings.HeatTransfer.Data.SolidsPCM.Generic matPCM2( x=0.2, k=1.4, c=840, d=2240, nSta=4, TSol=273.15 + 20.49, TLiq=273.15 + 20.51, LHea=100000) "PCM material with phase change near room temperature"; equation connect(step.y, TA.T); connect(step.y, TA1.T); connect(cheEqu.u1, heaFlo2.Q_flow); connect(cheEqu.u2, heaFlo1.Q_flow); connect(TA.port, conv1.fluid); connect(TA1.port, conv2.fluid); connect(conv2.solid, heaFlo2.port_a); connect(conv1.solid, heaFlo1.port_a); connect(heaFlo1.port_b, conPCM.port_a); connect(heaFlo2.port_b, con1.port_a); connect(con1.port_b, con2.port_a); connect(step.y, TA2.T); connect(TA2.port, conv3.fluid); connect(conv3.solid, conPCM2.port_a); end ConductorSingleLayerPCM;

Buildings.HeatTransfer.Examples.ConductorSteadyStateTransient Buildings.HeatTransfer.Examples.ConductorSteadyStateTransient

Test model for heat conductor

Buildings.HeatTransfer.Examples.ConductorSteadyStateTransient

Information

This example illustrates modeling of multi-layer materials. It also tests if the multi-layer material computes the same heat transfer with its boundary condition as two instances of a single layer material. The insulation is computed in steady-state, whereas the brick is computed using transient heat conduction.

The cheEqu block computes the difference between the heat fluxes, which should be equal except for the numerical approximation error of the solver.

Extends from Modelica.Icons.Example (Icon for runnable examples).

Parameters

TypeNameDefaultDescription
Brickbrickbrick(x=0.12, nStaRef=4) 
InsulationBoardinsulinsul(x=0.05, c=0, nStaRef=3)Insulation
Genericcompositecomposite(nLay=2, material={... 

Modelica definition

model ConductorSteadyStateTransient "Test model for heat conductor" extends Modelica.Icons.Example; parameter Buildings.HeatTransfer.Data.Solids.Brick brick(x=0.12, nStaRef=4); parameter Buildings.HeatTransfer.Data.Solids.InsulationBoard insul( x=0.05, c=0, nStaRef=3) "Insulation"; parameter Buildings.HeatTransfer.Data.OpaqueConstructions.Generic composite(nLay=2, material= {insul,brick}); Buildings.HeatTransfer.Conduction.MultiLayer conMul( A=2, layers=composite, stateAtSurface_b=false); Buildings.HeatTransfer.Conduction.SingleLayer con( A=2, material=brick, stateAtSurface_a=false, stateAtSurface_b=false); Buildings.HeatTransfer.Sources.FixedTemperature TB(T=293.15); Buildings.HeatTransfer.Sources.PrescribedTemperature TA; Modelica.Blocks.Sources.Step step( height=10, offset=293.15, startTime=3600); Buildings.HeatTransfer.Conduction.SingleLayer con1( A=2, material=insul, stateAtSurface_b=false); Buildings.HeatTransfer.Sources.FixedTemperature TB1(T=293.15); Buildings.HeatTransfer.Sources.PrescribedTemperature TA1; Buildings.HeatTransfer.Conduction.SingleLayer con2( A=2, material=brick, stateAtSurface_b=false, stateAtSurface_a=false); Buildings.HeatTransfer.Sources.PrescribedTemperature TA2; Buildings.HeatTransfer.Sources.FixedTemperature TB2(T=293.15); Modelica.Thermal.HeatTransfer.Sensors.HeatFlowSensor heaFlo1; Modelica.Thermal.HeatTransfer.Sensors.HeatFlowSensor heaFlo2; Modelica.Blocks.Math.Add cheEqu(k2=-1) "Check for equality"; Buildings.HeatTransfer.Convection.Interior conv1(A=2, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; Buildings.HeatTransfer.Convection.Interior conv2(A=2, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; equation connect(con.port_b, TB.port); connect(step.y, TA.T); connect(step.y, TA1.T); connect(con1.port_b, con2.port_a); connect(con2.port_b, TB1.port); connect(TA2.T, step.y); connect(heaFlo1.port_b, con1.port_a); connect(cheEqu.u1, heaFlo2.Q_flow); connect(cheEqu.u2, heaFlo1.Q_flow); connect(TA.port, con.port_a); connect(conMul.port_b, TB2.port); connect(conMul.port_a, heaFlo2.port_b); connect(TA1.port, conv1.fluid); connect(conv1.solid, heaFlo1.port_a); connect(TA2.port, conv2.fluid); connect(conv2.solid, heaFlo2.port_a); end ConductorSteadyStateTransient;

Buildings.HeatTransfer.Examples.ConductorStepResponse Buildings.HeatTransfer.Examples.ConductorStepResponse

Test model for heat conductor

Buildings.HeatTransfer.Examples.ConductorStepResponse

Information

This example illustrates modeling of multi-layer materials. It also tests if the multi-layer material computes the same heat transfer with its boundary condition as two instances of a single layer material. The insulation and the brick are computed using transient heat conduction.

The cheEqu block computes the difference between the heat fluxes, which should be equal except for the numerical approximation error of the solver.

Extends from Modelica.Icons.Example (Icon for runnable examples).

Parameters

TypeNameDefaultDescription
Concreteconcreteconcrete(x=0.12, nStaRef=4) 
Carpetcarpet carpet
Genericcompositecomposite(nLay=2, material={... 

Modelica definition

model ConductorStepResponse "Test model for heat conductor" extends Modelica.Icons.Example; parameter Buildings.HeatTransfer.Data.Solids.Concrete concrete(x=0.12, nStaRef=4); parameter Buildings.HeatTransfer.Data.Resistances.Carpet carpet "carpet"; parameter Buildings.HeatTransfer.Data.OpaqueConstructions.Generic composite( nLay=2, material={carpet,concrete}); Buildings.HeatTransfer.Conduction.MultiLayer conMul( A=2, layers=composite, stateAtSurface_b=false); Buildings.HeatTransfer.Conduction.SingleLayer con( A=2, material=carpet, stateAtSurface_a=false, stateAtSurface_b=false); Buildings.HeatTransfer.Sources.FixedTemperature TB(T=293.15); Buildings.HeatTransfer.Sources.PrescribedTemperature TA; Modelica.Blocks.Sources.Step step( height=10, offset=293.15, startTime=3600); Buildings.HeatTransfer.Conduction.SingleLayer con1( A=2, material=carpet, stateAtSurface_b=false); Buildings.HeatTransfer.Sources.FixedTemperature TB1( T=293.15); Buildings.HeatTransfer.Sources.PrescribedTemperature TA1; Buildings.HeatTransfer.Conduction.SingleLayer con2( A=2, material=concrete, stateAtSurface_b=false, stateAtSurface_a=false); Buildings.HeatTransfer.Sources.PrescribedTemperature TA2; Buildings.HeatTransfer.Sources.FixedTemperature TB2( T=293.15); Modelica.Thermal.HeatTransfer.Sensors.HeatFlowSensor heaFlo1; Modelica.Thermal.HeatTransfer.Sensors.HeatFlowSensor heaFlo2; Modelica.Blocks.Math.Add cheEqu(k2=-1) "Check for equality"; Buildings.HeatTransfer.Convection.Interior conv1( A=2, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; Buildings.HeatTransfer.Convection.Interior conv2( A=2, til=Buildings.Types.Tilt.Wall) "Convective heat transfer"; equation connect(con.port_b,TB. port); connect(step.y,TA. T); connect(step.y,TA1. T); connect(con1.port_b,con2. port_a); connect(con2.port_b,TB1. port); connect(TA2.T,step. y); connect(heaFlo1.port_b,con1. port_a); connect(cheEqu.u1, heaFlo2.Q_flow); connect(cheEqu.u2, heaFlo1.Q_flow); connect(TA.port,con. port_a); connect(conMul.port_b,TB2. port); connect(conMul.port_a,heaFlo2. port_b); connect(TA1.port, conv1.fluid); connect(conv1.solid, heaFlo1.port_a); connect(TA2.port, conv2.fluid); connect(conv2.solid, heaFlo2.port_a); end ConductorStepResponse;