Collection of models that illustrate model use and test models
Information
This package contains examples for the use of models that can be found in
Buildings.HeatTransfer.Windows.BaseClasses.
Extends from Modelica.Icons.ExamplesPackage (Icon for packages containing runnable examples).
Package Content
Name |
Description |
AbsorbedRadiation
|
Test model for absorbed radiation by windows |
AbsorbedRadiationElectrochromic
|
Test model for absorbed radiation for electrochromic window |
CenterOfGlass
|
Test model for center of glas heat transfer |
GasConvection
|
Test problem for convection in the gas layer |
GlassLayer
|
Test model for glass layer heat transfer |
InteriorConvection
|
Test model for the interior heat transfer due to convection |
Overhang
|
Test model for the overhang |
Shade
|
Test model for exterior shade heat transfer |
SideFins
|
Test model for side fins |
TransmittedRadiation
|
Test model for transmitted radiation through window |
WindowRadiation
|
Test model for window radiation |
WindowRadiationElectrochromic
|
Test model for window radiation for an electrochromic window |
Test model for absorbed radiation by windows
Information
This example illustrates modeling of window radiation.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
Type | Name | Default | Description |
Angle | lat | 0.34906585039887 | Latitude [rad] |
Angle | azi | 0 | Surface azimuth [rad] |
Angle | til | 1.5707963267949 | Surface tilt [rad] |
DoubleClearAir13Clear | glaSys | glaSys( shade=Buildings.He... | Parameters for glazing system |
Connectors
Type | Name | Description |
Bus | weaBus | |
Modelica definition
model AbsorbedRadiation
extends Modelica.Icons.Example;
parameter Modelica.SIunits.Angle lat=0.34906585039887 ;
parameter Modelica.SIunits.Angle azi=0 ;
parameter Modelica.SIunits.Angle til=1.5707963267949 ;
replaceable parameter Buildings.HeatTransfer.Data.GlazingSystems.DoubleClearAir13Clear
glaSys(
shade=
Buildings.HeatTransfer.Data.Shades.Gray(),
UFra=2,
haveExteriorShade=false,
haveInteriorShade=true)
constrainedby Data.GlazingSystems.Generic
;
BoundaryConditions.SolarIrradiation.DirectTiltedSurface HDirTil(
til=til,
lat=lat,
azi=azi);
BoundaryConditions.WeatherData.Bus weaBus;
BoundaryConditions.WeatherData.ReaderTMY3 weaDat(filNam=
Modelica.Utilities.Files.loadResource("modelica://Buildings/Resources/weatherdata/USA_IL_Chicago-OHare.Intl.AP.725300_TMY3.mos"),
computeWetBulbTemperature=false);
BoundaryConditions.SolarIrradiation.DiffuseIsotropic HDifTilIso(
til=til);
Modelica.Blocks.Sources.Constant shaCon(k=
if (glaSys.haveShade)
then 0.5
else
0);
Buildings.HeatTransfer.Windows.BaseClasses.AbsorbedRadiation winAbs(
AWin=1,
N=
size(glaSys.glass, 1),
tauGlaSol = glaSys.glass.tauSol,
rhoGlaSol_a=glaSys.glass.rhoSol_a,
rhoGlaSol_b=glaSys.glass.rhoSol_b,
xGla=glaSys.glass.x,
tauShaSol_a=glaSys.shade.tauSol_a,
tauShaSol_b=glaSys.shade.tauSol_b,
rhoShaSol_a=glaSys.shade.rhoSol_a,
rhoShaSol_b=glaSys.shade.rhoSol_b,
haveExteriorShade=glaSys.haveExteriorShade,
haveInteriorShade=glaSys.haveInteriorShade);
Modelica.Blocks.Sources.Constant HRoo(k=10);
equation
connect(weaDat.weaBus, weaBus);
connect(HDirTil.weaBus, weaBus);
connect(weaBus, HDifTilIso.weaBus);
connect(shaCon.y,winAbs. uSha);
connect(winAbs.HDir, HDirTil.H);
connect(HDifTilIso.H,winAbs. HDif);
connect(HDirTil.inc,winAbs. incAng);
connect(HRoo.y,winAbs. HRoo);
end AbsorbedRadiation;
Test model for absorbed radiation for electrochromic window
Information
This example tests the absorption of electrochromic glass.
Extends from AbsorbedRadiation (Test model for absorbed radiation by windows).
Parameters
Type | Name | Default | Description |
Angle | lat | 0.34906585039887 | Latitude [rad] |
Angle | azi | 0 | Surface azimuth [rad] |
Angle | til | 1.5707963267949 | Surface tilt [rad] |
Connectors
Type | Name | Description |
Bus | weaBus | |
Modelica definition
Test model for center of glas heat transfer
Information
This model tests the heat transfer for the center of the glass, with and without a shading device.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
Type | Name | Default | Description |
Area | A | 1 | Window surface area [m2] |
Boolean | linearize | false | Set to true to linearize emissive power |
DoubleClearAir13Clear | glaSys | glaSys( shade=Buildings.He... | Parameters for glazing system |
Modelica definition
model CenterOfGlass
extends Modelica.Icons.Example;
parameter Modelica.SIunits.Area A=1 ;
parameter Boolean linearize = false ;
Buildings.HeatTransfer.Windows.BaseClasses.CenterOfGlass sha(
A=A,
linearize=linearize,
til=1.5707963267949,
glaSys=glaSys) ;
Modelica.Blocks.Sources.Ramp uSha(
height=0.9,
duration=1,
offset=0.05) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature TAirOut
;
Modelica.Blocks.Sources.Constant TOut(k=273.15) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature TAirRoo
;
Buildings.HeatTransfer.Radiosity.OpaqueSurface radIn(A=A, absIR=0.8,
linearize=false) ;
Modelica.Blocks.Sources.Constant TRoo(k=293.15) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature TRadRoo
;
Buildings.HeatTransfer.Radiosity.RadiositySplitter radShaInt
;
Buildings.HeatTransfer.Windows.BaseClasses.CenterOfGlass nonSha(
A=A,
linearize=linearize,
til=1.5707963267949,
glaSys=glaSys) ;
Buildings.HeatTransfer.Radiosity.RadiositySplitter radShaOut
;
parameter Buildings.HeatTransfer.Data.GlazingSystems.DoubleClearAir13Clear glaSys(
shade=
Buildings.HeatTransfer.Data.Shades.Gray(),
haveExteriorShade=true,
haveInteriorShade=true,
UFra=2) ;
Buildings.HeatTransfer.Radiosity.OutdoorRadiosity radOut(A=A,
vieFacSky=0.5) ;
Modelica.Thermal.HeatTransfer.Components.Convection conRooSha
;
Modelica.Thermal.HeatTransfer.Components.Convection conOutSha(dT(start=0))
;
Modelica.Thermal.HeatTransfer.Components.Convection conOutNonSha1(dT(start=0))
;
Modelica.Thermal.HeatTransfer.Components.Convection conRooNonSha
;
Modelica.Blocks.Sources.Constant hA(k=4*A)
;
Modelica.Blocks.Math.Product hASha ;
Modelica.Blocks.Math.Product hANonSha
;
Buildings.HeatTransfer.Windows.BaseClasses.ShadingSignal shaCon(haveShade=
glaSys.haveExteriorShade
or glaSys.haveInteriorShade)
;
Modelica.Blocks.Sources.Constant QAbs[
size(glaSys.glass, 1)](
each k=0)
;
Modelica.Blocks.Math.MultiSum sumJ(nu=2)
;
equation
connect(TOut.y, TAirOut.T);
connect(TRoo.y, TAirRoo.T);
connect(TRadRoo.port, radIn.heatPort);
connect(TRadRoo.T, TRoo.y);
connect(radIn.JOut, radShaInt.JIn);
connect(radOut.JOut, radShaOut.JIn);
connect(hA.y, hANonSha.u1);
connect(hASha.u1, hA.y);
connect(hASha.y, conOutSha.Gc);
connect(hASha.y, conRooSha.Gc);
connect(hANonSha.y, conOutNonSha1.Gc);
connect(hANonSha.y, conRooNonSha.Gc);
connect(conOutSha.solid, sha.glass_a);
connect(conOutSha.fluid, TAirOut.port);
connect(nonSha.glass_a, conOutNonSha1.solid);
connect(conOutNonSha1.fluid, TAirOut.port);
connect(nonSha.glass_b, conRooNonSha.solid);
connect(conRooNonSha.fluid, TAirRoo.port);
connect(conRooSha.fluid, TAirRoo.port);
connect(conRooSha.solid, sha.glass_b);
connect(radShaOut.JOut_1, sha.JIn_a);
connect(radShaOut.JOut_2, nonSha.JIn_a);
connect(radShaInt.JOut_1, sha.JIn_b);
connect(radShaInt.JOut_2, nonSha.JIn_b);
connect(shaCon.yCom, hANonSha.u2);
connect(shaCon.yCom, nonSha.u);
connect(shaCon.y, radShaOut.u);
connect(shaCon.y, radShaInt.u);
connect(shaCon.y, sha.u);
connect(uSha.y, shaCon.u);
connect(shaCon.y, hASha.u2);
connect(QAbs.y, nonSha.QAbs_flow);
connect(QAbs.y, sha.QAbs_flow);
connect(radOut.TOut, TOut.y);
connect(TOut.y, radOut.TBlaSky);
connect(radIn.JIn, sumJ.y);
connect(sha.JOut_b, sumJ.u[1]);
connect(nonSha.JOut_b, sumJ.u[2]);
end CenterOfGlass;
Test problem for convection in the gas layer
Information
Extends from Modelica.Icons.Example (Icon for runnable examples).
Modelica definition
model GasConvection
extends Modelica.Icons.Example;
Buildings.HeatTransfer.Windows.BaseClasses.GasConvection conVer(
A=1,
linearize=false,
gas=
Buildings.HeatTransfer.Data.Gases.Air(x=0.1),
til=Buildings.Types.Tilt.Wall) ;
Modelica.Blocks.Sources.Ramp TBC(
duration=1,
offset=283.15,
height=20) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature T_a1
;
Buildings.HeatTransfer.Sources.FixedTemperature T_b1(T=293.15)
;
Modelica.Blocks.Sources.Constant u(k=1) ;
Buildings.HeatTransfer.Windows.BaseClasses.GasConvection conCei(
A=1,
linearize=false,
gas=
Buildings.HeatTransfer.Data.Gases.Air(x=0.1),
til=Buildings.Types.Tilt.Ceiling)
;
Buildings.HeatTransfer.Sources.PrescribedTemperature T_a2
;
Buildings.HeatTransfer.Sources.FixedTemperature T_b2(T=293.15)
;
Buildings.HeatTransfer.Windows.BaseClasses.GasConvection conFlo(
A=1,
linearize=false,
gas=
Buildings.HeatTransfer.Data.Gases.Air(x=0.1),
til=Buildings.Types.Tilt.Floor)
;
Buildings.HeatTransfer.Sources.PrescribedTemperature T_a3
;
Buildings.HeatTransfer.Sources.FixedTemperature T_b3(T=293.15)
;
equation
connect(TBC.y, T_a1.T);
connect(T_a1.port, conVer.port_a);
connect(conVer.port_b, T_b1.port);
connect(u.y, conVer.u);
connect(TBC.y, T_a2.T);
connect(T_a2.port, conCei.port_a);
connect(conCei.port_b, T_b2.port);
connect(u.y, conCei.u);
connect(TBC.y, T_a3.T);
connect(T_a3.port, conFlo.port_a);
connect(conFlo.port_b, T_b3.port);
connect(u.y, conFlo.u);
end GasConvection;
Test model for glass layer heat transfer
Information
This model tests one glas layer.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
Type | Name | Default | Description |
Area | A | 1 | Window surface area [m2] |
Boolean | linearize | false | Set to true to linearize emissive power |
Modelica definition
model GlassLayer
extends Modelica.Icons.Example;
parameter Modelica.SIunits.Area A=1 ;
parameter Boolean linearize = false ;
Buildings.HeatTransfer.Windows.BaseClasses.GlassLayer sha(
A=A,
absIR_a=0.5,
tauIR=0.2,
x=0.015,
k=1,
linearize=linearize,
absIR_b=0.5) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature TAirOut
;
Modelica.Blocks.Sources.Constant TOut(k=273.15) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature TAirRoo
;
Buildings.HeatTransfer.Radiosity.OpaqueSurface radOut(A=A, absIR=0.8,
linearize=false) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature TRadOut
;
Buildings.HeatTransfer.Radiosity.OpaqueSurface radIn(A=A, absIR=0.8,
linearize=false) ;
Modelica.Blocks.Sources.Constant TRoo(k=293.15) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature TRadRoo
;
Modelica.Blocks.Sources.Constant QAbs_flow(k=0) ;
Buildings.HeatTransfer.Radiosity.RadiositySplitter radShaInt
;
Buildings.HeatTransfer.Windows.BaseClasses.GlassLayer nonSha(
A=A,
absIR_a=0.5,
tauIR=0.2,
x=0.015,
k=1,
linearize=linearize,
absIR_b=0.5) ;
Buildings.HeatTransfer.Radiosity.RadiositySplitter radShaOut
;
Modelica.Thermal.HeatTransfer.Components.Convection conRooSha
;
Modelica.Thermal.HeatTransfer.Components.Convection conRooNonSha
;
Modelica.Blocks.Sources.Constant hA(k=4*A)
;
Modelica.Blocks.Math.Product hASha ;
Modelica.Blocks.Math.Product hANonSha
;
Modelica.Thermal.HeatTransfer.Components.Convection conOutSha(
dT(start=0))
;
Modelica.Thermal.HeatTransfer.Components.Convection conOutNonSha1(
dT(start=0))
;
Modelica.Blocks.Sources.Ramp uSha(
height=0.9,
duration=1,
offset=0.05) ;
Buildings.HeatTransfer.Windows.BaseClasses.ShadingSignal shaCon(haveShade=
true) ;
Modelica.Blocks.Math.MultiSum sumJOut(nu=2)
;
Modelica.Blocks.Math.MultiSum sumJRoo(nu=2)
;
equation
connect(TOut.y, TAirOut.T);
connect(TRadOut.port, radOut.heatPort);
connect(TRadOut.T, TOut.y);
connect(TRoo.y, TAirRoo.T);
connect(TRadRoo.port, radIn.heatPort);
connect(TRadRoo.T, TRoo.y);
connect(QAbs_flow.y, sha.QAbs_flow);
connect(radShaOut.JIn, radOut.JOut);
connect(radIn.JOut, radShaInt.JIn);
connect(radShaOut.JOut_1, sha.JIn_a);
connect(radShaOut.JOut_2, nonSha.JIn_a);
connect(radShaInt.JOut_1, sha.JIn_b);
connect(radShaInt.JOut_2, nonSha.JIn_b);
connect(QAbs_flow.y, nonSha.QAbs_flow);
connect(hA.y, hANonSha.u1);
connect(hASha.u1, hA.y);
connect(nonSha.port_a, conOutNonSha1.solid);
connect(conOutNonSha1.fluid, TAirOut.port);
connect(sha.port_a, conOutSha.solid);
connect(conOutSha.fluid, TAirOut.port);
connect(nonSha.port_b, conRooNonSha.solid);
connect(sha.port_b, conRooSha.solid);
connect(conRooSha.fluid, TAirRoo.port);
connect(conRooNonSha.fluid, TAirRoo.port);
connect(hASha.y, conOutSha.Gc);
connect(hASha.y, conRooSha.Gc);
connect(hANonSha.y, conOutNonSha1.Gc);
connect(hANonSha.y, conRooNonSha.Gc);
connect(shaCon.yCom, hANonSha.u2);
connect(shaCon.yCom, nonSha.u);
connect(shaCon.y, radShaOut.u);
connect(shaCon.y, radShaInt.u);
connect(shaCon.y, sha.u);
connect(uSha.y,shaCon. u);
connect(shaCon.y, hASha.u2);
connect(radOut.JIn, sumJOut.y);
connect(sha.JOut_a, sumJOut.u[1]);
connect(nonSha.JOut_a, sumJOut.u[2]);
connect(radIn.JIn, sumJRoo.y);
connect(sha.JOut_b, sumJRoo.u[1]);
connect(nonSha.JOut_b, sumJRoo.u[2]);
end GlassLayer;
Test model for the interior heat transfer due to convection
Information
This is a test model for the interior side convective heat transfer.
During the simulation, the shading control signal is changed, which
causes a change in the convective heat flow rate.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Modelica definition
Test model for the overhang
Information
This example uses the basic overhang model with solar angles as input and calculates the fraction of total window area that is exposed to the sun.
For a detail description of the solar angles used in the model, see
Buildings.BoundaryConditions.SolarGeometry.
For a detailed description of the overhang block, see
Buildings.HeatTransfer.Windows.BaseClasses.Overhang.
The required data for the solar angle calculations is obtained from weather data.
Solar angles used in this model are:
The values of the parameters of the overhang model have been set in such
a way that the overhang in non-symmetric with respect to the window center-line.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Connectors
Type | Name | Description |
Bus | weaBus | |
Modelica definition
model Overhang
extends Modelica.Icons.Example;
Buildings.BoundaryConditions.SolarGeometry.IncidenceAngle incAng(
lat=weaDat.lat,
azi=Buildings.Types.Azimuth.S,
til=Buildings.Types.Tilt.Wall) ;
Buildings.BoundaryConditions.WeatherData.ReaderTMY3 weaDat(filNam=
Modelica.Utilities.Files.loadResource("modelica://Buildings/Resources/weatherdata/USA_IL_Chicago-OHare.Intl.AP.725300_TMY3.mos"))
;
Buildings.HeatTransfer.Windows.BaseClasses.Overhang ove(
gap=0.1,
azi=Buildings.Types.Azimuth.S,
lat=weaDat.lat,
wL=0,
wR=0.95,
dep=0.5,
hWin=2,
wWin=0.1) ;
Buildings.BoundaryConditions.SolarGeometry.BaseClasses.WallSolarAzimuth walSolAzi
;
Buildings.BoundaryConditions.WeatherData.Bus weaBus;
equation
connect(weaDat.weaBus, incAng.weaBus);
connect(incAng.y, walSolAzi.incAng);
connect(walSolAzi.verAzi, ove.verAzi);
connect(weaDat.weaBus, ove.weaBus);
connect(weaDat.weaBus, weaBus);
connect(weaBus.solAlt, walSolAzi.alt);
connect(weaBus.solAlt, ove.alt);
end Overhang;
Test model for exterior shade heat transfer
Information
This model tests the shading device. Note that the temperature of the shading device changes
slightly as the shade control signal changes (i.e., as the shade is lowered).
This is because the shade has a different emissive power than the glass, which changes the
energy balance.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
Type | Name | Default | Description |
Area | A | 1 | Window surface area [m2] |
Boolean | linearize | true | Set to true to linearize emissive power |
Modelica definition
model Shade
extends Modelica.Icons.Example;
parameter Modelica.SIunits.Area A=1 ;
parameter Boolean linearize = true ;
Buildings.HeatTransfer.Windows.BaseClasses.ShadeRadiation extShaRad(
A=A,
linearize=false,
absIR_air=0.3,
absIR_glass=0.3,
tauIR_air=0.3,
tauIR_glass=0.3,
thisSideHasShade=true) ;
Modelica.Blocks.Sources.Ramp uSha(
height=0.9,
duration=1,
offset=0.05) ;
Modelica.Blocks.Sources.Constant TOut(k=273.15) ;
Buildings.HeatTransfer.Radiosity.OpaqueSurface radOut(A=A, absIR=0.8,
linearize=false) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature TRadOut
;
Buildings.HeatTransfer.Radiosity.OpaqueSurface radIn(A=A, absIR=0.8,
linearize=false) ;
Modelica.Blocks.Sources.Constant TRoo(k=293.15) ;
Buildings.HeatTransfer.Sources.PrescribedTemperature TRadRoo
;
Modelica.Blocks.Sources.Constant QSol_shade(k=0)
;
Buildings.HeatTransfer.Radiosity.RadiositySplitter radShaInt
;
Buildings.HeatTransfer.Windows.BaseClasses.ShadeRadiation extNonShaRad(
A=A,
linearize=false,
thisSideHasShade=false,
absIR_air=0,
absIR_glass=0,
tauIR_air=0.3,
tauIR_glass=0.3) ;
Buildings.HeatTransfer.Radiosity.RadiositySplitter radShaOut
;
Buildings.HeatTransfer.Sources.PrescribedTemperature TAirOut
;
Buildings.HeatTransfer.Sources.PrescribedTemperature TAirRoo
;
Buildings.HeatTransfer.Windows.BaseClasses.ShadingSignal shaCon(haveShade=
true);
Modelica.Blocks.Math.Gain GConSha(k=10*A, y(unit="W/K"))
;
Modelica.Blocks.Math.Gain GConUns(k=10*A, y(unit="W/K"))
;
Modelica.Blocks.Math.MultiSum sumJRoo(nu=2) ;
Modelica.Blocks.Math.MultiSum sumJOut(nu=2) ;
Buildings.HeatTransfer.Windows.BaseClasses.ShadeConvection extShaCon(A=A,
thisSideHasShade=true) ;
Buildings.HeatTransfer.Windows.BaseClasses.ShadeConvection extNonShaCon(A=A,
thisSideHasShade=false)
;
equation
connect(TRadOut.port, radOut.heatPort);
connect(TRadOut.T, TOut.y);
connect(TRadRoo.port, radIn.heatPort);
connect(TRadRoo.T, TRoo.y);
connect(radShaOut.JIn, radOut.JOut);
connect(radIn.JOut, radShaInt.JIn);
connect(radShaOut.JOut_1, extShaRad.JIn_air);
connect(radShaOut.JOut_2, extNonShaRad.JIn_air);
connect(radShaInt.JOut_1, extShaRad.JIn_glass);
connect(radShaInt.JOut_2, extNonShaRad.JIn_glass);
connect(TAirOut.T, TOut.y);
connect(TAirRoo.T, TRoo.y);
connect(shaCon.y, extShaRad.u);
connect(shaCon.y, radShaOut.u);
connect(uSha.y, shaCon.u);
connect(shaCon.yCom, extNonShaRad.u);
connect(GConSha.u, shaCon.y);
connect(shaCon.yCom, GConUns.u);
connect(shaCon.y, radShaInt.u);
connect(radIn.JIn, sumJRoo.y);
connect(radOut.JIn, sumJOut.y);
connect(TAirRoo.port, extShaCon.glass);
connect(TAirRoo.port, extNonShaCon.glass);
connect(extShaCon.air, TAirOut.port);
connect(extNonShaCon.air, TAirOut.port);
connect(GConUns.y, extNonShaCon.Gc);
connect(GConSha.y, extShaCon.Gc);
connect(extShaCon.TSha, extShaRad.TSha);
connect(extShaCon.QRadAbs_flow, extShaRad.QRadAbs_flow);
connect(extNonShaRad.TSha, extNonShaCon.TSha);
connect(extNonShaRad.QRadAbs_flow, extNonShaCon.QRadAbs_flow);
connect(extShaRad.JOut_air, sumJOut.u[1]);
connect(extNonShaRad.JOut_air, sumJOut.u[2]);
connect(extShaRad.JOut_glass, sumJRoo.u[1]);
connect(extNonShaRad.JOut_glass, sumJRoo.u[2]);
connect(extShaRad.QSolAbs_flow, QSol_shade.y);
connect(extNonShaRad.QSolAbs_flow, QSol_shade.y);
end Shade;
Test model for side fins
Information
This example uses the basic side fins model with solar angles as input and calculates the fraction of total window area that is exposed to the sun.
For a detailed description of the solar angles used in the model,
see to documentation in the package
Buildings.BoundaryConditions.SolarGeometry.
For a detail description of side fin model, see
Buildings.HeatTransfer.Windows.BaseClasses.SideFins.
The required data for the solar angle calculations are obtained from the weather data.
Solar angles used in this model are:
Extends from Modelica.Icons.Example (Icon for runnable examples).
Modelica definition
model SideFins
extends Modelica.Icons.Example;
Buildings.BoundaryConditions.SolarGeometry.ZenithAngle zen(lat=0.73129295658562)
;
Buildings.BoundaryConditions.SolarGeometry.IncidenceAngle incAng(
azi=0,
lat=0.73129295658562,
til=1.5707963267949) ;
Buildings.BoundaryConditions.WeatherData.ReaderTMY3 weaDat(filNam=
Modelica.Utilities.Files.loadResource("modelica://Buildings/Resources/weatherdata/USA_IL_Chicago-OHare.Intl.AP.725300_TMY3.mos"))
;
Buildings.HeatTransfer.Windows.BaseClasses.SideFins fin(
gap=0.1,
h=0.7,
dep=1.0,
hWin=1.5,
wWin=2.0) ;
Buildings.BoundaryConditions.SolarGeometry.BaseClasses.AltitudeAngle
altAng ;
Buildings.BoundaryConditions.SolarGeometry.BaseClasses.WallSolarAzimuth walSolAzi
;
equation
connect(weaDat.weaBus, zen.weaBus);
connect(weaDat.weaBus, incAng.weaBus);
connect(zen.y, altAng.zen);
connect(altAng.alt, fin.alt);
connect(walSolAzi.verAzi, fin.verAzi);
connect(altAng.alt, walSolAzi.alt);
connect(incAng.y, walSolAzi.incAng);
end SideFins;
Test model for transmitted radiation through window
Information
This example illustrates modeling of window transmittance.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
Type | Name | Default | Description |
Angle | lat | 0.34906585039887 | Latitude [rad] |
Angle | azi | 0 | Surface azimuth [rad] |
Angle | til | 1.5707963267949 | Surface tilt [rad] |
DoubleClearAir13Clear | glaSys | glaSys( shade=Buildings.He... | Parameters for glazing system |
Connectors
Type | Name | Description |
Bus | weaBus | Weather data bus |
Modelica definition
model TransmittedRadiation
extends Modelica.Icons.Example;
parameter Modelica.SIunits.Angle lat=0.34906585039887 ;
parameter Modelica.SIunits.Angle azi=0 ;
parameter Modelica.SIunits.Angle til=1.5707963267949 ;
parameter Buildings.HeatTransfer.Data.GlazingSystems.DoubleClearAir13Clear glaSys(
shade=
Buildings.HeatTransfer.Data.Shades.Gray(),
UFra=2,
haveExteriorShade=false,
haveInteriorShade=true) ;
BoundaryConditions.SolarIrradiation.DirectTiltedSurface HDirTil(
til=til,
lat=lat,
azi=azi) ;
BoundaryConditions.WeatherData.Bus weaBus ;
BoundaryConditions.WeatherData.ReaderTMY3 weaDat(filNam=
Modelica.Utilities.Files.loadResource("modelica://Buildings/Resources/weatherdata/USA_IL_Chicago-OHare.Intl.AP.725300_TMY3.mos"))
;
BoundaryConditions.SolarIrradiation.DiffuseIsotropic HDifTilIso(
til=til) ;
Modelica.Blocks.Sources.Constant shaCon(k=
if (glaSys.haveShade)
then 0.5
else
0);
Buildings.HeatTransfer.Windows.BaseClasses.TransmittedRadiation winTra(
AWin=1,
N=
size(glaSys.glass, 1),
tauGlaSol=glaSys.glass.tauSol,
rhoGlaSol_a=glaSys.glass.rhoSol_a,
rhoGlaSol_b=glaSys.glass.rhoSol_b,
xGla=glaSys.glass.x,
tauShaSol_a=glaSys.shade.tauSol_a,
tauShaSol_b=glaSys.shade.tauSol_b,
rhoShaSol_a=glaSys.shade.rhoSol_a,
rhoShaSol_b=glaSys.shade.rhoSol_b,
haveExteriorShade=glaSys.haveExteriorShade,
haveInteriorShade=glaSys.haveInteriorShade);
equation
connect(weaDat.weaBus, weaBus);
connect(HDirTil.weaBus, weaBus);
connect(weaBus, HDifTilIso.weaBus);
connect(shaCon.y,winTra. uSha);
connect(winTra.HDir, HDirTil.H);
connect(HDifTilIso.H,winTra. HDif);
connect(HDirTil.inc,winTra. incAng);
end TransmittedRadiation;
Test model for window radiation
Information
This example illustrates modeling of window radiation.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
Type | Name | Default | Description |
Angle | lat | 0.34906585039887 | Latitude [rad] |
Angle | azi | 0 | Surface azimuth [rad] |
Angle | til | 1.5707963267949 | Surface tilt [rad] |
DoubleClearAir13Clear | glaSys | glaSys( shade=Buildings.He... | Parameters for glazing system |
Connectors
Type | Name | Description |
Bus | weaBus | Weather data bus |
Modelica definition
model WindowRadiation
extends Modelica.Icons.Example;
parameter Modelica.SIunits.Angle lat=0.34906585039887 ;
parameter Modelica.SIunits.Angle azi=0 ;
parameter Modelica.SIunits.Angle til=1.5707963267949 ;
replaceable parameter Buildings.HeatTransfer.Data.GlazingSystems.DoubleClearAir13Clear
glaSys(
shade=
Buildings.HeatTransfer.Data.Shades.Gray(),
UFra=2,
haveExteriorShade=false,
haveInteriorShade=true)
constrainedby Data.GlazingSystems.Generic
;
BoundaryConditions.SolarIrradiation.DirectTiltedSurface HDirTil(
til=til,
lat=lat,
azi=azi) ;
BoundaryConditions.WeatherData.Bus weaBus ;
BoundaryConditions.WeatherData.ReaderTMY3 weaDat(filNam=
Modelica.Utilities.Files.loadResource("modelica://Buildings/Resources/weatherdata/USA_IL_Chicago-OHare.Intl.AP.725300_TMY3.mos"))
;
BoundaryConditions.SolarIrradiation.DiffuseIsotropic HDifTilIso(
til=til) ;
Modelica.Blocks.Sources.Constant shaCon(k=
if (glaSys.haveShade)
then 0.5
else
0);
Modelica.Blocks.Math.Gain HRoo(k=0.1) ;
Buildings.HeatTransfer.Windows.BaseClasses.WindowRadiation winRad(
AWin=1,
N=
size(glaSys.glass, 1),
tauGlaSol=glaSys.glass.tauSol,
rhoGlaSol_a=glaSys.glass.rhoSol_a,
rhoGlaSol_b=glaSys.glass.rhoSol_b,
xGla=glaSys.glass.x,
tauShaSol_a=glaSys.shade.tauSol_a,
tauShaSol_b=glaSys.shade.tauSol_b,
rhoShaSol_a=glaSys.shade.rhoSol_a,
rhoShaSol_b=glaSys.shade.rhoSol_b,
haveExteriorShade=glaSys.haveExteriorShade,
haveInteriorShade=glaSys.haveInteriorShade);
equation
connect(weaDat.weaBus, weaBus);
connect(HDirTil.weaBus, weaBus);
connect(weaBus, HDifTilIso.weaBus);
connect(HRoo.y, winRad.HRoo);
connect(shaCon.y, winRad.uSha);
connect(winRad.QTraDif_flow, HRoo.u);
connect(winRad.HDir, HDirTil.H);
connect(HDifTilIso.H, winRad.HDif);
connect(HDirTil.inc, winRad.incAng);
end WindowRadiation;
Test model for window radiation for an electrochromic window
Information
This example tests the implementation of the electrochromic window.
Extends from WindowRadiation (Test model for window radiation).
Parameters
Type | Name | Default | Description |
Angle | lat | 0.34906585039887 | Latitude [rad] |
Angle | azi | 0 | Surface azimuth [rad] |
Angle | til | 1.5707963267949 | Surface tilt [rad] |
Connectors
Type | Name | Description |
Bus | weaBus | Weather data bus |
Modelica definition