Buildings.Fluid.MixingVolumes.BaseClasses

Package with base classes for Buildings.Fluid.MixingVolumes

Information

This package contains base classes that are used to construct the models in Buildings.Fluid.MixingVolumes.

Extends from Modelica.Icons.BasesPackage (Icon for packages containing base classes).

Package Content

Name	Description
MixingVolumeHeatMoisturePort	Mixing volume with heat and moisture port and initialize_p not set to final
MixingVolumeHeatPort	Mixing volume with heat port and initialize_p not set to final
PartialMixingVolume	Partial mixing volume with inlet and outlet ports (flow reversal is allowed)
Validation	Collection of validation models

Buildings.Fluid.MixingVolumes.BaseClasses.MixingVolumeHeatMoisturePort

Mixing volume with heat and moisture port and initialize_p not set to final

Information

Mixing volume with a heat port.

This model is identical to Buildings.Fluid.MixingVolumes.BaseClasses.PartialMixingVolume, except that it has a heat and a moisture port.

Note that this model is typically only used to implement new component models that have staggered volumes. In contrast to Buildings.Fluid.MixingVolumes.MixingVolumeMoistAir, it does not set initialize_p to final in order for this model to be usable in staggered volumes which require one pressure to be set to initialize_p = not Medium.singleState and all others to false.

Extends from Buildings.Fluid.MixingVolumes.BaseClasses.PartialMixingVolume (Partial mixing volume with inlet and outlet ports (flow reversal is allowed)).

Parameters

Connectors

Modelica definition

Buildings.Fluid.MixingVolumes.BaseClasses.MixingVolumeHeatPort

Mixing volume with heat port and initialize_p not set to final

Information

Mixing volume with a heat port.

This model is identical to Buildings.Fluid.MixingVolumes.BaseClasses.PartialMixingVolume, except that it has a heat port.

Note that this model is typically only used to implement new component models that have staggered volumes. In contrast to Buildings.Fluid.MixingVolumes.MixingVolume, it does not set initialize_p to final in order for this model to be usable in staggered volumes which require one pressure to be set to initialize_p = not Medium.singleState and all others to false.

Extends from Buildings.Fluid.MixingVolumes.BaseClasses.PartialMixingVolume (Partial mixing volume with inlet and outlet ports (flow reversal is allowed)).

Parameters

Connectors

Modelica definition

Buildings.Fluid.MixingVolumes.BaseClasses.PartialMixingVolume

Partial mixing volume with inlet and outlet ports (flow reversal is allowed)

Information

This is a partial model of an instantaneously mixed volume. It is used as the base class for all fluid volumes of the package Buildings.Fluid.MixingVolumes.

Typical use and important parameters

Set the constant sensibleOnly=true if the model that extends or instantiates this model sets mWat_flow = 0.

Set the constant simplify_mWat_flow = true to simplify the equation

  port_a.m_flow + port_b.m_flow = - mWat_flow;

to

  port_a.m_flow + port_b.m_flow = 0;

This causes an error in the mass balance of about 0.5%, but generally leads to simpler equations because the pressure drop equations are then decoupled from the mass exchange in this component.

To increase the numerical robustness of the model, the constant prescribedHeatFlowRate can be set by the user. This constant only has an effect if the model has exactly two fluid ports connected, and if it is used as a steady-state model. Use the following settings:

• Set prescribedHeatFlowRate=true if the only means of heat transfer at the heatPort is a prescribed heat flow rate that is not a function of the temperature difference between the medium and an ambient temperature. Examples include an ideal electrical heater, a pump that rejects heat into the fluid stream, or a chiller that removes heat based on a performance curve. If the heatPort is not connected, then set prescribedHeatFlowRate=true as in this case, heatPort.Q_flow=0.
• Set prescribedHeatFlowRate=false if there is heat flow at the heatPort computed as K * (T-heatPort.T), for some temperature T and some conductance K, which may itself be a function of temperature or mass flow rate.
  If there is a combination of K * (T-heatPort.T) and a prescribed heat flow rate, for example a solar collector that dissipates heat to the ambient and receives heat from the solar radiation, then set prescribedHeatFlowRate=false.

Set the parameter use_C_flow = true to enable an input connector for the trace substance flow rate.

Implementation

If the model is (i) operated in steady-state, (ii) has two fluid ports connected, and (iii) prescribedHeatFlowRate=true or allowFlowReversal=false, then the model uses Buildings.Fluid.Interfaces.StaticTwoPortConservationEquation in order to use the same energy and mass balance implementation as is used as in steady-state component models. In this situation, the functions inStream are used for the two flow directions rather than the function actualStream, which is less efficient. However, the use of inStream has the disadvantage that hOut has to be computed, in Buildings.Fluid.Interfaces.StaticTwoPortConservationEquation, using

if allowFlowReversal then
  hOut = Buildings.Utilities.Math.Functions.regStep(y1=port_b.h_outflow,
                                                    y2=port_a.h_outflow,
                                                    x=port_a.m_flow,
                                                    x_small=m_flow_small/1E3);
else
  hOut = port_b.h_outflow;
end if;

Hence, for allowFlowReversal=true, if hOut were to be used to compute the temperature that drives heat transfer such as by conduction, then the heat transfer would depend on upstream and the downstream temperatures for small mass flow rates. This can give wrong results. Consider for example a mass flow rate that is positive but very close to zero. Suppose the upstream temperature is 20ˆC, the downstream temperature is 10ˆC, and the heat port is connected through a heat conductor to a boundary condition of 20ˆC. Then, hOut = (port_b.h_outflow + port_a.h_outflow)/2 and hence the temperature heatPort.T is 15ˆC. Therefore, heat is added to the component. As the mass flow rate is by assumption very small, the fluid that leaves the component will have a very high temperature, violating the 2nd law. To avoid this situation, if prescribedHeatFlowRate=false, then the model Buildings.Fluid.Interfaces.ConservationEquation is used instead of Buildings.Fluid.Interfaces.StaticTwoPortConservationEquation.

For simple models that uses this model, see Buildings.Fluid.MixingVolumes.

Extends from Buildings.Fluid.Interfaces.LumpedVolumeDeclarations (Declarations for lumped volumes).

Parameters

Connectors

Modelica definition