Buildings.Examples.VAVCO2.BaseClasses
Package with base classes for Buildings.Examples.VAVCO2
Information
This package contains base classes that are used to construct the models in Buildings.Examples.VAVCO2.
Extends from Modelica.Icons.BasesPackage (Icon for packages containing base classes).
Package Content
| Name | Description |
|---|---|
 DamperControl
|
Local loop controller for damper |
 Occupancy
|
Model for occupancy |
 RoomLeakage
|
Room leakage model |
 RoomVAV
|
Model for CO2 emitted by people |
 Suite
|
Model of a suite consisting of five rooms of the MIT system model |
Buildings.Examples.VAVCO2.BaseClasses.DamperControl
Local loop controller for damper
Information
Extends from Modelica.Blocks.Interfaces.SISO (Single Input Single Output continuous control block).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| Real | CO2Set | 700E-6 | CO2 set point in volume fraction |
| Real | Kp | 10 | Gain |
Connectors
| Type | Name | Description |
|---|---|---|
| input RealInput | u | Connector of Real input signal |
| output RealOutput | y | Connector of Real output signal |
Modelica definition
block DamperControl "Local loop controller for damper"
extends Modelica.Blocks.Interfaces.SISO;
parameter Real CO2Set = 700E-6 "CO2 set point in volume fraction";
parameter Real Kp = 10 "Gain";
Buildings.Controls.Continuous.LimPID con(
yMin=0,
y_start=0.5,
Ti=1,
controllerType=Modelica.Blocks.Types.SimpleController.P,
k=Kp,
yMax=1,
reverseAction=true,
Td=60);
protected
Modelica.Blocks.Sources.Constant xSetNor(k=1) "CO2 set point (normalized)";
Modelica.Blocks.Math.Gain gain1(k=1/CO2Set)
"Gain. Division by CO2Set is to normalize the control error";
equation
connect(con.y, y);
connect(xSetNor.y, con.u_s);
connect(gain1.y, con.u_m);
connect(u, gain1.u);
end DamperControl;
Buildings.Examples.VAVCO2.BaseClasses.Occupancy
Model for occupancy
Information
Extends from Modelica.Blocks.Icons.Block (Basic graphical layout of input/output block).
Connectors
| Type | Name | Description |
|---|---|---|
| output RealOutput | y1[2] | Connector of Real output signals |
| output RealOutput | y2[2] | Connector of Real output signals |
| output RealOutput | y3[2] | Connector of Real output signals |
Modelica definition
model Occupancy "Model for occupancy"
extends Modelica.Blocks.Icons.Block;
Modelica.Blocks.Sources.CombiTimeTable office1(
extrapolation=Modelica.Blocks.Types.Extrapolation.Periodic,
smoothness=Modelica.Blocks.Types.Smoothness.ConstantSegments,
tableOnFile=false,
table=[-6,0.0;
8,2;
9,3;
12,2;
13,6;
15,3;
16,4;
18,0],
timeScale=3600) "Office with double occupancy";
Modelica.Blocks.Sources.CombiTimeTable office2(
extrapolation=Modelica.Blocks.Types.Extrapolation.Periodic,
smoothness=Modelica.Blocks.Types.Smoothness.ConstantSegments,
tableOnFile=false,
table=[-6,0.0;
8,2;
9,3;
12,2;
13,5;
15,3;
16,6;
18,0],
timeScale=3600) "Office with double occupancy";
Modelica.Blocks.Sources.CombiTimeTable cla1(
extrapolation=Modelica.Blocks.Types.Extrapolation.Periodic,
smoothness=Modelica.Blocks.Types.Smoothness.ConstantSegments,
tableOnFile=false,
table=[-6,0.0;
8,25;
9,20;
10,30;
12,0;
13,30;
15,40;
16,20;
18,0],
timeScale=3600) "Class room";
Modelica.Blocks.Sources.CombiTimeTable cla2(
extrapolation=Modelica.Blocks.Types.Extrapolation.Periodic,
smoothness=Modelica.Blocks.Types.Smoothness.ConstantSegments,
tableOnFile=false,
table=[-6,0.0;
8,20;
9,10;
10,20;
11,15;
12,0;
13,30;
15,20;
16,25;
18,0],
timeScale=3600) "Class room";
Modelica.Blocks.Sources.CombiTimeTable smaRoo1(
extrapolation=Modelica.Blocks.Types.Extrapolation.Periodic,
smoothness=Modelica.Blocks.Types.Smoothness.ConstantSegments,
tableOnFile=false,
table=[-6,0.0;
8,0.4;
9,1;
12,1;
13,0.5;
14,1.0;
16,0.5;
18,0],
timeScale=3600) "Small rooms";
Modelica.Blocks.Sources.CombiTimeTable smaRoo2(
extrapolation=Modelica.Blocks.Types.Extrapolation.Periodic,
smoothness=Modelica.Blocks.Types.Smoothness.ConstantSegments,
tableOnFile=false,
table=[-6,0.0;
8,0.4;
9,1;
10,0.4;
12,1;
13,0.3;
14,0.4;
16,0.2;
18,0],
timeScale=3600) "Small rooms";
Modelica.Blocks.Interfaces.RealOutput y1[2]
"Connector of Real output signals";
Modelica.Blocks.Interfaces.RealOutput y2[2]
"Connector of Real output signals";
Modelica.Blocks.Interfaces.RealOutput y3[2]
"Connector of Real output signals";
Modelica.Blocks.Math.Gain sca1(k=2) "Scaling for occupancy";
Modelica.Blocks.Math.Gain sca2(k=3) "Scaling for occupancy";
Modelica.Blocks.Math.Gain sca3(k=3) "Scaling for occupancy";
Modelica.Blocks.Math.Gain sca4(k=2) "Scaling for occupancy";
Modelica.Blocks.Math.Gain sca5(k=3) "Scaling for occupancy";
Modelica.Blocks.Math.Gain sca6(k=3) "Scaling for occupancy";
Modelica.Blocks.Routing.Multiplex2 mul1(
final n1=1,
final n2=1)
"Multiplex to route signals";
Modelica.Blocks.Routing.Multiplex2 mul2(
final n1=1,
final n2=1)
"Multiplex to route signals";
Modelica.Blocks.Routing.Multiplex2 mul3(
final n1=1,
final n2=1)
"Multiplex to route signals";
equation
connect(y1, mul1.y);
connect(mul1.u1[1], sca1.y);
connect(mul1.u2[1], sca4.y);
connect(mul2.y, y2);
connect(mul3.y, y3);
connect(sca2.y, mul2.u1[1]);
connect(sca5.y, mul2.u2[1]);
connect(sca3.y, mul3.u1[1]);
connect(sca6.y, mul3.u2[1]);
connect(cla1.y[1], sca1.u);
connect(cla2.y[1], sca4.u);
connect(office1.y[1], sca2.u);
connect(office2.y[1], sca5.u);
connect(smaRoo1.y[1], sca3.u);
connect(smaRoo2.y[1], sca6.u);
end Occupancy;
Buildings.Examples.VAVCO2.BaseClasses.RoomLeakage
Room leakage model
Information
Room leakage used in the MIT system model.
Extends from Buildings.BaseClasses.BaseIcon (Base icon).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| replaceable package Medium | Modelica.Media.Interfaces.Pa... | Medium in the component | |
Connectors
| Type | Name | Description |
|---|---|---|
| replaceable package Medium | Medium in the component | |
| input RealInput | p | Pressure |
| FluidPort_b | port_b | |
Modelica definition
model RoomLeakage "Room leakage model"
extends Buildings.BaseClasses.BaseIcon;
replaceable package Medium =
Modelica.Media.Interfaces.PartialMedium "Medium in the component";
Buildings.Fluid.FixedResistances.PressureDrop res(
m_flow_nominal=1,
redeclare package Medium = Medium,
dp_nominal=1000) "Resistance model";
Modelica.Blocks.Interfaces.RealInput p "Pressure";
Modelica.Fluid.Interfaces.FluidPort_b port_b(redeclare package Medium =
Medium);
Buildings.Fluid.Sources.Boundary_pT amb( redeclare package Medium =Medium,
nPorts=1,
use_p_in=true,
p=101325,
T=293.15);
equation
connect(res.port_b, port_b);
connect(p, amb.p_in);
connect(amb.ports[1], res.port_a);
end RoomLeakage;
Buildings.Examples.VAVCO2.BaseClasses.RoomVAV
Model for CO2 emitted by people
Information
Model of a room and a plenum. CO2 is injected into the room. An air damper controls how much air flows into the room to track the CO2 level.
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| replaceable package Medium | Modelica.Media.Interfaces.Pa... | Medium in the component | |
| Volume | VRoo | Volume of room [m3] | |
| Volume | VPle | Volume of plenum [m3] | |
| Area | ADam | Damper face area [m2] | |
| MassFlowRate | m_flow_nominal | Nominal mass flow rate [kg/s] | |
Connectors
| Type | Name | Description |
|---|---|---|
| replaceable package Medium | Medium in the component | |
| FluidPort_a | portRoo1 | Fluid port |
| FluidPort_a | portSup | Fluid port |
| FluidPort_a | portRet | Fluid port |
| FluidPort_a | portRoo2 | Fluid port |
| output RealOutput | yDam | Damper control signal |
| input RealInput | nPeo | Number of people |
Modelica definition
model RoomVAV "Model for CO2 emitted by people"
replaceable package Medium =
Modelica.Media.Interfaces.PartialMedium "Medium in the component";
parameter Modelica.SIunits.Volume VRoo "Volume of room";
parameter Modelica.SIunits.Volume VPle "Volume of plenum";
parameter Modelica.SIunits.Area ADam "Damper face area";
parameter Modelica.SIunits.MassFlowRate m_flow_nominal
"Nominal mass flow rate";
Buildings.Fluid.Actuators.Dampers.VAVBoxExponential vav(
redeclare package Medium = Medium,
m_flow_nominal=m_flow_nominal,
dp_nominal=1E2,
from_dp=false);
Buildings.Fluid.MixingVolumes.MixingVolume vol(
redeclare package Medium = Medium,
V=VRoo,
nPorts=5,
m_flow_nominal=m_flow_nominal,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
use_C_flow=true) "Room volume";
Buildings.Fluid.Sensors.TraceSubstances senCO2(
redeclare package Medium = Medium) "Sensor at volume";
Buildings.Fluid.MixingVolumes.MixingVolume ple(
redeclare package Medium = Medium,
V=VPle,
m_flow_nominal=m_flow_nominal,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
nPorts=2)
"Plenum volume";
Modelica.Fluid.Interfaces.FluidPort_a portRoo1(
redeclare package Medium = Medium) "Fluid port";
Modelica.Fluid.Interfaces.FluidPort_a portSup(
redeclare package Medium = Medium) "Fluid port";
Modelica.Fluid.Interfaces.FluidPort_a portRet(
redeclare package Medium = Medium) "Fluid port";
Modelica.Fluid.Interfaces.FluidPort_a portRoo2(
redeclare package Medium = Medium) "Fluid port";
Modelica.Blocks.Interfaces.RealOutput yDam "Damper control signal";
Modelica.Blocks.Interfaces.RealInput nPeo "Number of people";
Modelica.Blocks.Math.Gain gaiCO2(k=8.18E-6) "CO2 emission per person";
Buildings.Fluid.Sensors.Conversions.To_VolumeFraction volFraCO2(
MMMea=Modelica.Media.
IdealGases.Common.SingleGasesData.CO2.MM) "CO2 volume fraction";
DamperControl con(Kp=1) "Damper controller";
Modelica.Blocks.Math.Gain peoDen(k=2.5/VRoo) "People density per m2";
Modelica.Blocks.Sources.RealExpression vavACH(
y=vav.m_flow*3600/VRoo/1.2)
"VAV box air change per hour";
Buildings.Fluid.FixedResistances.PressureDrop dpPle(
redeclare package Medium = Medium,
m_flow_nominal=m_flow_nominal,
dp_nominal=20,
from_dp=true);
equation
connect(senCO2.C, volFraCO2.m);
connect(volFraCO2.V, con.u);
connect(con.y, yDam);
connect(con.y, vav.y);
connect(nPeo, gaiCO2.u);
connect(nPeo, peoDen.u);
connect(portSup, vav.port_a);
connect(portRoo1, vol.ports[1]);
connect(vav.port_b, vol.ports[2]);
connect(senCO2.port, vol.ports[3]);
connect(portRoo2, vol.ports[4]);
connect(dpPle.port_a, vol.ports[5]);
connect(vol.C_flow[1], gaiCO2.y);
connect(dpPle.port_b, ple.ports[1]);
connect(ple.ports[2], portRet);
end RoomVAV;
Buildings.Examples.VAVCO2.BaseClasses.Suite
Model of a suite consisting of five rooms of the MIT system model
Information
Model of a suite consisting of five rooms for the MIT system model.
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| replaceable package Medium | Modelica.Media.Interfaces.Pa... | Medium in the component | |
| Real | scaM_flow | Scaling factor for mass flow rate | |
| MassFlowRate | m0Tot_flow | scaM_flow*(5.196 + 2.8428 + ... | [kg/s] |
Connectors
| Type | Name | Description |
|---|---|---|
| replaceable package Medium | Medium in the component | |
| input RealInput | p | Pressure |
| FluidPort_b | port_aSup | |
| FluidPort_b | port_bExh | |
| output RealOutput | p_rel | Relative pressure signal |
| output RealOutput | yDam[6] | VAV damper positions |
| output RealOutput | dPRoo | Room pressurization |
Modelica definition
model Suite "Model of a suite consisting of five rooms of the MIT system model"
replaceable package Medium =
Modelica.Media.Interfaces.PartialMedium "Medium in the component";
Modelica.Blocks.Interfaces.RealInput p "Pressure";
Modelica.Fluid.Interfaces.FluidPort_b port_aSup(
redeclare package Medium = Medium);
parameter Real scaM_flow "Scaling factor for mass flow rate";
parameter Modelica.SIunits.MassFlowRate m0Tot_flow=
scaM_flow*(5.196+2.8428+1.0044+0.9612+0.3624+0.1584);
Buildings.Fluid.FixedResistances.Junction spl34(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{1,-1,-1},
dp_nominal={0.176,-0.844,-0.0662},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Buildings.Fluid.FixedResistances.Junction mix55(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{-1,1,1},
dp_nominal=1E3*{-0.263200E-02,0.999990E-03,0.649000E-03},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Buildings.Fluid.FixedResistances.PressureDrop res13(
m_flow_nominal=scaM_flow*1,
dp_nominal=0.1E3,
redeclare package Medium = Medium);
Buildings.Fluid.FixedResistances.PressureDrop res14(
m_flow_nominal=scaM_flow*1,
dp_nominal=0.1E3,
redeclare package Medium = Medium);
Buildings.Fluid.FixedResistances.PressureDrop res15(
m_flow_nominal=scaM_flow*1,
dp_nominal=0.1E3,
redeclare package Medium = Medium);
Buildings.Fluid.FixedResistances.PressureDrop res16(
m_flow_nominal=scaM_flow*1,
dp_nominal=0.1E3,
redeclare package Medium = Medium);
Buildings.Fluid.FixedResistances.PressureDrop res17(
m_flow_nominal=scaM_flow*1,
dp_nominal=0.1E3,
redeclare package Medium = Medium);
Buildings.Fluid.FixedResistances.Junction spl35(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{1,-1,-1},
dp_nominal=1E3*{0.371000E-04,-0.259000E-02,-0.131000E-02},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Buildings.Fluid.FixedResistances.Junction spl36(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{1,-1,-1},
dp_nominal=1E3*{0.211000E-03,-0.128000E-01,-0.223000E-02},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Buildings.Fluid.FixedResistances.Junction spl37(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{1,-1,-1},
dp_nominal=1E3*{0.730000E-03,-0.128000E-01,-0.938000E-02},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Buildings.Fluid.FixedResistances.Junction spl38(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{1,-1,-1},
dp_nominal=1E3*{0.731000E-02,-0.895000E-01,-0.942000E-01},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Buildings.Fluid.FixedResistances.Junction mix54(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{-1,1,1},
dp_nominal=1E3*{-0.653000E-02,0.271000E-03,0.402000E-04},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Buildings.Fluid.FixedResistances.Junction mix53(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{-1,1,1},
dp_nominal=1E3*{-0.566000E-01,0.541000E-02,0.749000E-04},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Buildings.Fluid.FixedResistances.Junction mix52(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{-1,1,1},
dp_nominal=1E3*{-0.353960,0.494000E-03,0.922000E-03},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Buildings.Fluid.FixedResistances.Junction mix51(
redeclare package Medium = Medium,
m_flow_nominal=scaM_flow*{-1,1,1},
dp_nominal=1E3*{-0.847600E-01,1.89750,0.150000E-02},
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState);
Modelica.Fluid.Interfaces.FluidPort_b port_bExh(
redeclare package Medium = Medium);
Buildings.Fluid.FixedResistances.PressureDrop res1(
m_flow_nominal=scaM_flow*1,
dp_nominal=0.1E3,
redeclare package Medium = Medium);
RoomVAV roo45(
redeclare package Medium = Medium,
ADam=scaM_flow*0.49,
m_flow_nominal=scaM_flow*5.196,
VRoo=1820,
VPle=396) "Room model";
RoomVAV roo46(
redeclare package Medium = Medium,
ADam=scaM_flow*0.245,
m_flow_nominal=scaM_flow*2.8428,
VRoo=1210,
VPle=330) "Room model";
RoomVAV roo47(
redeclare package Medium = Medium,
ADam=scaM_flow*0.128,
m_flow_nominal=scaM_flow*1.0044,
VRoo=647,
VPle=125) "Room model";
RoomVAV roo48(
redeclare package Medium = Medium,
ADam=scaM_flow*0.128,
m_flow_nominal=scaM_flow*0.9612,
VRoo=385,
VPle=107) "Room model";
RoomVAV roo49(
redeclare package Medium = Medium,
ADam=scaM_flow*0.0494,
m_flow_nominal=scaM_flow*0.3624,
VRoo=48,
VPle=13) "Room model";
RoomVAV roo50(
redeclare package Medium = Medium,
ADam=scaM_flow*0.024,
m_flow_nominal=scaM_flow*0.1584,
VRoo=155,
VPle=43) "Room model";
Occupancy occ "Occupancy";
Buildings.Fluid.Sensors.RelativePressure dpMea(
redeclare package Medium = Medium) "Static pressure measurement";
Modelica.Blocks.Interfaces.RealOutput p_rel "Relative pressure signal";
Modelica.Blocks.Interfaces.RealOutput yDam[6] "VAV damper positions";
Buildings.Fluid.Sensors.Pressure pRoo(redeclare package Medium = Medium)
"Room pressure";
Modelica.Blocks.Math.Feedback feeBac;
Modelica.Blocks.Interfaces.RealOutput dPRoo "Room pressurization";
equation
connect(spl38.port_2, roo50.portSup);
connect(port_aSup, spl34.port_1);
connect(spl34.port_2, spl35.port_1);
connect(spl35.port_2, spl36.port_1);
connect(spl36.port_2, spl37.port_1);
connect(spl37.port_2, spl38.port_1);
connect(dpMea.port_a, spl38.port_1);
connect(pRoo.p, feeBac.u2);
connect(roo50.portRoo2, pRoo.port);
connect(spl34.port_3, roo45.portSup);
connect(spl35.port_3, roo46.portSup);
connect(spl36.port_3, roo47.portSup);
connect(spl37.port_3, roo48.portSup);
connect(spl38.port_3, roo49.portSup);
connect(dpMea.port_b, res16.port_b);
connect(p, feeBac.u1);
connect(dPRoo, feeBac.y);
connect(dpMea.p_rel, p_rel);
connect(roo45.yDam, yDam[1]);
connect(roo46.yDam, yDam[2]);
connect(roo47.yDam, yDam[3]);
connect(roo48.yDam, yDam[4]);
connect(roo49.yDam, yDam[5]);
connect(roo50.yDam, yDam[6]);
connect(occ.y1[1], roo45.nPeo);
connect(occ.y1[2], roo46.nPeo);
connect(occ.y2[1], roo47.nPeo);
connect(occ.y2[2], roo48.nPeo);
connect(occ.y3[1], roo49.nPeo);
connect(occ.y3[2], roo50.nPeo);
connect(port_bExh, mix55.port_1);
connect(mix55.port_2, mix54.port_1);
connect(mix54.port_2, mix53.port_1);
connect(mix53.port_2, mix52.port_1);
connect(mix52.port_2, mix51.port_1);
connect(mix51.port_2, roo50.portRet);
connect(roo48.portRet, mix51.port_3);
connect(mix52.port_3, roo49.portRet);
connect(roo47.portRet, mix53.port_3);
connect(roo46.portRet, mix54.port_3);
connect(roo45.portRet, mix55.port_3);
connect(res1.port_b, roo45.portRoo1);
connect(roo45.portRoo2, res13.port_a);
connect(res13.port_b, roo46.portRoo1);
connect(roo46.portRoo2, res14.port_a);
connect(res14.port_b, roo47.portRoo1);
connect(roo47.portRoo2, res15.port_a);
connect(res15.port_b, roo48.portRoo1);
connect(roo48.portRoo2, res16.port_a);
connect(res16.port_b, roo49.portRoo1);
connect(roo49.portRoo2, res17.port_a);
connect(res17.port_b, roo50.portRoo1);
connect(roo50.portRoo2, res1.port_a);
end Suite;