Buildings.Fluid.HeatPumps.Validation
Collection of models that validate the heat pump models
Information
This package contains models that validate the heat pump models. The examples plot various outputs, which have been verified against analytical solutions. These model outputs are stored as reference data to allow continuous validation whenever models in the library change.
Extends from Modelica.Icons.ExamplesPackage (Icon for packages containing runnable examples).
Package Content
| Name | Description |
|---|---|
 Carnot_TCon_LimitedCapacity
|
Test model for Carnot_TCon with limited heating capacity |
| Carnot_TCon_LowTemperature
|
Test model for Carnot_TCon with low condenser leaving water temperature |
| Carnot_TCon_etaPL
|
Test model for the part load efficiency curve with condenser leaving temperature as input signal |
| Carnot_TCon_reverseFlow
|
Test model for heat pump based on Carnot efficiency and condenser outlet temperature control signal |
| Carnot_y_etaCar
|
Test model for heat pump based on Carnot efficiency with etaCar as parameter |
| Carnot_y_etaPL
|
Test model for the part load efficiency curve with compressor speed as input signal |
| ReciprocatingWaterToWater_Dynamic
|
Test model for variable speed reciprocating water to water heat pump |
| ReciprocatingWaterToWater_ScalingFactor
|
Test model for variable speed reciprocating water to water heat pump |
| ReciprocatingWaterToWater_Static
|
Test model for static, reciprocating water to water heat pump |
| ReciprocatingWaterToWater_VariableSpeed
|
Test model for reciprocating water to water heat pump |
| ScrollWaterToWater_Dynamic
|
Test model for scroll water to water heat pump |
| ScrollWaterToWater_ScalingFactor
|
Test model for scroll water to water heat pump |
| ScrollWaterToWater_Static
|
Test model for static scroll water to water heat pump |
| ScrollWaterToWater_TemperatureProtection
|
Test model for temperature protection of scroll water to water heat pump |
| ScrollWaterToWater_VariableSpeed
|
Test model for scroll water to water heat pump |
Buildings.Fluid.HeatPumps.Validation.Carnot_TCon_LimitedCapacity
Test model for Carnot_TCon with limited heating capacity
Information
This example extends from Buildings.Fluid.HeatPumps.Examples.Carnot_TCon but limits the heating capacity.
Extends from Examples.Carnot_TCon (Test model for heat pump based on Carnot efficiency and condenser outlet temperature control signal).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| TemperatureDifference | dTEva_nominal | -5 | Temperature difference evaporator inlet-outlet [K] |
| TemperatureDifference | dTCon_nominal | 10 | Temperature difference condenser outlet-inlet [K] |
| HeatFlowRate | QCon_flow_nominal | 100E3 | Evaporator heat flow rate [W] |
| MassFlowRate | m1_flow_nominal | QCon_flow_nominal/dTCon_nomi... | Nominal mass flow rate at condenser [kg/s] |
Modelica definition
model Carnot_TCon_LimitedCapacity
"Test model for Carnot_TCon with limited heating capacity"
extends Examples.Carnot_TCon(heaPum(QCon_flow_max=250000));
end Carnot_TCon_LimitedCapacity;
Buildings.Fluid.HeatPumps.Validation.Carnot_TCon_LowTemperature
Test model for Carnot_TCon with low condenser leaving water temperature
Information
This example extends from Buildings.Fluid.HeatPumps.Examples.Carnot_TCon but decreases the set point for the leaving condenser temperature to be below its inlet temperature, in which case the model provides no heating. Towards the end of the simulation, the inlet temperature of the condenser is decreased to be below the evaporator temperature. In this domain, the model requires cooling again. While this is not a meaningful operating point for the model, the example verifies that it robustly simulates this regime.
Extends from Examples.Carnot_TCon (Test model for heat pump based on Carnot efficiency and condenser outlet temperature control signal).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| TemperatureDifference | dTEva_nominal | -5 | Temperature difference evaporator inlet-outlet [K] |
| TemperatureDifference | dTCon_nominal | 10 | Temperature difference condenser outlet-inlet [K] |
| HeatFlowRate | QCon_flow_nominal | 100E3 | Evaporator heat flow rate [W] |
| MassFlowRate | m1_flow_nominal | QCon_flow_nominal/dTCon_nomi... | Nominal mass flow rate at condenser [kg/s] |
Modelica definition
model Carnot_TCon_LowTemperature
"Test model for Carnot_TCon with low condenser leaving water temperature"
extends Examples.Carnot_TCon(TConLvg(height=-32), sou1(use_T_in=true));
Modelica.Blocks.Sources.Ramp TConEnt(
duration=60,
offset=273.15 + 20,
startTime=3000,
height=-19) "Control signal for condenser entering temperature";
equation
connect(TConEnt.y, sou1.T_in);
end Carnot_TCon_LowTemperature;
Buildings.Fluid.HeatPumps.Validation.Carnot_TCon_etaPL
Test model for the part load efficiency curve with condenser leaving temperature as input signal
Information
This example extends from Buildings.Fluid.HeatPumps.Examples.Carnot_TCon but has a part load efficiency that varies with the load.
Extends from Examples.Carnot_TCon (Test model for heat pump based on Carnot efficiency and condenser outlet temperature control signal).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| TemperatureDifference | dTEva_nominal | -5 | Temperature difference evaporator inlet-outlet [K] |
| TemperatureDifference | dTCon_nominal | 10 | Temperature difference condenser outlet-inlet [K] |
| HeatFlowRate | QCon_flow_nominal | 100E3 | Evaporator heat flow rate [W] |
| MassFlowRate | m1_flow_nominal | QCon_flow_nominal/dTCon_nomi... | Nominal mass flow rate at condenser [kg/s] |
Modelica definition
model Carnot_TCon_etaPL
"Test model for the part load efficiency curve with condenser leaving temperature as input signal"
extends Examples.Carnot_TCon(heaPum(a={0.7,0.3}), TConLvg(height=10, offset=273.15
+ 25));
end Carnot_TCon_etaPL;
Buildings.Fluid.HeatPumps.Validation.Carnot_TCon_reverseFlow
Test model for heat pump based on Carnot efficiency and condenser outlet temperature control signal
Information
Example that simulates a heat pump whose efficiency is scaled based on the
Carnot cycle.
The heat pump takes as an input the condenser leaving water temperature.
The condenser mass flow rate is computed in such a way that it has
a temperature difference equal to dTCon_nominal.
This example checks the correct behavior if a mass flow rate attains zero.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| TemperatureDifference | dTEva_nominal | -10 | Temperature difference evaporator inlet-outlet [K] |
| TemperatureDifference | dTCon_nominal | 10 | Temperature difference condenser outlet-inlet [K] |
| HeatFlowRate | QCon_flow_nominal | 100E3 | Evaporator heat flow rate [W] |
| MassFlowRate | m1_flow_nominal | QCon_flow_nominal/dTCon_nomi... | Nominal mass flow rate at condenser [kg/s] |
Modelica definition
model Carnot_TCon_reverseFlow
"Test model for heat pump based on Carnot efficiency and condenser outlet temperature control signal"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.TemperatureDifference dTEva_nominal=-10
"Temperature difference evaporator inlet-outlet";
parameter Modelica.SIunits.TemperatureDifference dTCon_nominal=10
"Temperature difference condenser outlet-inlet";
parameter Modelica.SIunits.HeatFlowRate QCon_flow_nominal=100E3
"Evaporator heat flow rate";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=QCon_flow_nominal/
dTCon_nominal/4200 "Nominal mass flow rate at condenser";
Modelica.Blocks.Sources.Constant TConLvg(k=273.15 + 40)
"Control signal for condenser leaving temperature";
final parameter Modelica.SIunits.SpecificHeatCapacity cp2_default=
Medium2.specificHeatCapacityCp(Medium2.setState_pTX(
Medium2.p_default,
Medium2.T_default,
Medium2.X_default))
"Specific heat capacity of medium 2 at default medium state";
Modelica.Blocks.Sources.Ramp mCon_flow(
duration=60,
startTime=1800,
height=-2*m1_flow_nominal,
offset=m1_flow_nominal) "Mass flow rate for condenser";
Carnot_TCon heaPum(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
dTEva_nominal=dTEva_nominal,
dTCon_nominal=dTCon_nominal,
m1_flow_nominal=m1_flow_nominal,
show_T=true,
use_eta_Carnot_nominal=true,
etaCarnot_nominal=0.3,
QCon_flow_nominal=QCon_flow_nominal,
allowFlowReversal1=true,
allowFlowReversal2=true,
dp1_nominal=6000,
dp2_nominal=6000) "Heat pump";
Sources.MassFlowSource_T sou1(
nPorts=1,
redeclare package Medium = Medium1,
use_m_flow_in=true,
T=293.15);
Sources.MassFlowSource_T sou2(
nPorts=1,
redeclare package Medium = Medium2,
use_T_in=false,
use_m_flow_in=true,
T=288.15);
Sources.FixedBoundary sin1(redeclare package Medium = Medium1, nPorts=1);
Sources.FixedBoundary sin2(nPorts=1, redeclare package Medium = Medium2);
Modelica.Blocks.Math.Gain mEva_flow(k=-1/cp2_default/dTEva_nominal)
"Evaporator mass flow rate";
Modelica.Blocks.Math.Add QEva_flow(k2=-1) "Evaporator heat flow rate";
equation
connect(sou1.ports[1], heaPum.port_a1);
connect(sou2.ports[1], heaPum.port_a2);
connect(sin2.ports[1], heaPum.port_b2);
connect(QEva_flow.y, mEva_flow.u);
connect(heaPum.port_b1, sin1.ports[1]);
connect(mEva_flow.y, sou2.m_flow_in);
connect(TConLvg.y, heaPum.TSet);
connect(mCon_flow.y, sou1.m_flow_in);
connect(heaPum.QCon_flow, QEva_flow.u1);
connect(QEva_flow.u2, heaPum.P);
end Carnot_TCon_reverseFlow;
Buildings.Fluid.HeatPumps.Validation.Carnot_y_etaCar
Test model for heat pump based on Carnot efficiency with etaCar as parameter
Information
This example extends from
Buildings.Fluid.HeatPumps.Examples.Carnot_y
but uses the parameter etaCar instead of COP_nominal.
Extends from Buildings.Fluid.HeatPumps.Examples.Carnot_y (Test model for heat pump based on Carnot efficiency).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| Real | COP_nominal | 6 | Nominal COP |
| Power | P_nominal | 10E3 | Nominal compressor power (at y=1) [W] |
| TemperatureDifference | dTEva_nominal | -10 | Temperature difference evaporator outlet-inlet [K] |
| TemperatureDifference | dTCon_nominal | 10 | Temperature difference condenser outlet-inlet [K] |
| MassFlowRate | m2_flow_nominal | -P_nominal*(COP_nominal - 1)... | Nominal mass flow rate at chilled water side [kg/s] |
| MassFlowRate | m1_flow_nominal | P_nominal*COP_nominal/cp1_de... | Nominal mass flow rate at condenser water wide [kg/s] |
Modelica definition
model Carnot_y_etaCar
"Test model for heat pump based on Carnot efficiency with etaCar as parameter"
extends Buildings.Fluid.HeatPumps.Examples.Carnot_y(heaPum(
use_eta_Carnot_nominal=true, etaCarnot_nominal=0.494805));
end Carnot_y_etaCar;
Buildings.Fluid.HeatPumps.Validation.Carnot_y_etaPL
Test model for the part load efficiency curve with compressor speed as input signal
Information
This example extends from Buildings.Fluid.HeatPumps.Examples.Carnot_y but uses a part load efficiency curve that is different from 1.
Extends from Examples.Carnot_y (Test model for heat pump based on Carnot efficiency).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| Real | COP_nominal | 6 | Nominal COP |
| Power | P_nominal | 10E3 | Nominal compressor power (at y=1) [W] |
| TemperatureDifference | dTEva_nominal | -10 | Temperature difference evaporator outlet-inlet [K] |
| TemperatureDifference | dTCon_nominal | 10 | Temperature difference condenser outlet-inlet [K] |
| MassFlowRate | m2_flow_nominal | -P_nominal*(COP_nominal - 1)... | Nominal mass flow rate at chilled water side [kg/s] |
| MassFlowRate | m1_flow_nominal | P_nominal*COP_nominal/cp1_de... | Nominal mass flow rate at condenser water wide [kg/s] |
Modelica definition
model Carnot_y_etaPL
"Test model for the part load efficiency curve with compressor speed as input signal"
extends Examples.Carnot_y(heaPum(
a={0.7,0.3},
T1_start=303.15,
T2_start=278.15));
end Carnot_y_etaPL;
Buildings.Fluid.HeatPumps.Validation.ReciprocatingWaterToWater_Dynamic
Test model for variable speed reciprocating water to water heat pump
Information
Model that demonstrates the use of the Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heat pump model. This validation case also tests the stage input to the heat pump models.
With constant inlet source and load water temperatures, the heat pumps cycle on and off. The apparent capacity of the dynamic model is compared to the steady-state model and to the condenser heat transfer rate.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 0.47 | Nominal mass flow rate on the condenser side [kg/s] |
| MassFlowRate | m2_flow_nominal | 0.47 | Nominal mass flow rate on the evaporator side [kg/s] |
| MassFlowRate | flowSource | 0.79 | Mass flow rate on the condenser side [kg/s] |
| MassFlowRate | flowLoad | 0.47 | Mass flow rate on the evaporator side [kg/s] |
Modelica definition
model ReciprocatingWaterToWater_Dynamic
"Test model for variable speed reciprocating water to water heat pump"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=0.47
"Nominal mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate m2_flow_nominal=0.47
"Nominal mass flow rate on the evaporator side";
parameter Modelica.SIunits.MassFlowRate flowSource=0.79
"Mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate flowLoad=0.47
"Mass flow rate on the evaporator side";
Buildings.Fluid.Sources.FixedBoundary sin2(redeclare package Medium = Medium2,
nPorts=2) "Source side sink";
Buildings.Fluid.Sources.FixedBoundary sin1(redeclare package Medium = Medium1,
nPorts=2) "Load side sink";
Modelica.Fluid.Sources.MassFlowSource_T loa(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.RealExpression mLoa(y=flowLoad)
"Load side mass flwo rate";
Modelica.Blocks.Sources.RealExpression mSou(y=flowSource)
"Source side mass flow rate";
Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heaPum(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
show_T=true,
enable_variable_speed=false,
per=Buildings.Fluid.HeatPumps.Data.ReciprocatingWaterToWater.Generic(
etaEle=0.696,
PLos=100,
dTSup=9.82,
UACon=2210,
UAEva=1540,
pisDis=0.00162,
cleFac=0.069,
pDro=99290),
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState,
enable_temperature_protection=false)
"Reciprocating water to water heat pump";
Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heaPum1(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
tau1=15,
tau2=15,
enable_variable_speed=false,
per=Buildings.Fluid.HeatPumps.Data.ReciprocatingWaterToWater.Generic(
etaEle=0.696,
PLos=100,
dTSup=9.82,
UACon=2210,
UAEva=1540,
pisDis=0.00162,
cleFac=0.069,
pDro=99290),
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyStateInitial,
enable_temperature_protection=false)
"Reciprocating water to water heat pump with transient effects";
Modelica.Blocks.Sources.Pulse N(width=60, period=500)
"Heat pump control signal";
Modelica.Fluid.Sources.MassFlowSource_T loa1(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou1(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.Constant TLoa(k=285.15) "Load side fluid temperature";
Modelica.Blocks.Sources.Constant TSou(k=283.15)
"Source side fluid temperature";
Modelica.Blocks.Sources.RealExpression appCap(y=heaPum1.port_a1.m_flow*(
heaPum1.port_b1.h_outflow - loa1.ports[1].h_outflow))
"Apparent capacity of the heat pump";
Modelica.Blocks.Math.RealToInteger realToInteger;
equation
connect(mSou.y, sou.m_flow_in);
connect(heaPum.port_a2, sou.ports[1]);
connect(heaPum.port_b1, sin1.ports[1]);
connect(heaPum.port_a1, loa.ports[1]);
connect(heaPum.port_b2, sin2.ports[1]);
connect(sin2.ports[2], heaPum1.port_b2);
connect(mLoa.y, loa.m_flow_in);
connect(mLoa.y, loa1.m_flow_in);
connect(sou1.ports[1], heaPum1.port_a2);
connect(mSou.y, sou1.m_flow_in);
connect(TSou.y, sou1.T_in);
connect(sou.T_in, sou1.T_in);
connect(TLoa.y, loa1.T_in);
connect(TLoa.y, loa.T_in);
connect(loa1.ports[1], heaPum1.port_a1);
connect(heaPum1.port_b1, sin1.ports[2]);
connect(N.y, realToInteger.u);
connect(realToInteger.y, heaPum.stage);
connect(realToInteger.y, heaPum1.stage);
end ReciprocatingWaterToWater_Dynamic;
Buildings.Fluid.HeatPumps.Validation.ReciprocatingWaterToWater_ScalingFactor
Test model for variable speed reciprocating water to water heat pump
Information
Model that demonstrates the use of the Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heat pump model. This validation case also tests the stage input to the heat pump models.
With constant inlet source and load water temperatures, the heat pumps cycle on and off. The capacity of the scaled heat pump model is compared to the capacity of the non-scaled heat pump model.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 0.47 | Nominal mass flow rate on the condenser side [kg/s] |
| MassFlowRate | m2_flow_nominal | 0.47 | Nominal mass flow rate on the evaporator side [kg/s] |
| MassFlowRate | flowSource | 0.79 | Mass flow rate on the condenser side [kg/s] |
| MassFlowRate | flowLoad | 0.47 | Mass flow rate on the evaporator side [kg/s] |
| Real | scaling_factor | 2.41 | Scaling factor for heat pump capacity |
Modelica definition
model ReciprocatingWaterToWater_ScalingFactor
"Test model for variable speed reciprocating water to water heat pump"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=0.47
"Nominal mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate m2_flow_nominal=0.47
"Nominal mass flow rate on the evaporator side";
parameter Modelica.SIunits.MassFlowRate flowSource=0.79
"Mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate flowLoad=0.47
"Mass flow rate on the evaporator side";
parameter Real scaling_factor=2.41 "Scaling factor for heat pump capacity";
Buildings.Fluid.Sources.FixedBoundary sin2(redeclare package Medium = Medium2,
nPorts=2) "Source side sink";
Buildings.Fluid.Sources.FixedBoundary sin1(redeclare package Medium = Medium1,
nPorts=2) "Load side sink";
Modelica.Fluid.Sources.MassFlowSource_T loa(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.RealExpression mLoa(y=flowLoad*scaling_factor)
"Load side mass flwo rate";
Modelica.Blocks.Sources.RealExpression mSou(y=flowSource*scaling_factor)
"Source side mass flow rate";
Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heaPum(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
enable_variable_speed=false,
per=Buildings.Fluid.HeatPumps.Data.ReciprocatingWaterToWater.Generic(
etaEle=0.696,
PLos=100,
dTSup=9.82,
UACon=2210,
UAEva=1540,
pisDis=0.00162,
cleFac=0.069,
pDro=99290),
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
enable_temperature_protection=false)
"Reciprocating water to water heat pump";
Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heaPum1(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
enable_variable_speed=false,
scaling_factor=scaling_factor,
m1_flow_nominal=m1_flow_nominal*scaling_factor,
m2_flow_nominal=m2_flow_nominal*scaling_factor,
per=Buildings.Fluid.HeatPumps.Data.ReciprocatingWaterToWater.Generic(
etaEle=0.696,
PLos=100,
dTSup=9.82,
UACon=2210,
UAEva=1540,
pisDis=0.00162,
cleFac=0.069,
pDro=99290),
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
enable_temperature_protection=false)
"Reciprocating water to water heat pump with transient effects";
Modelica.Blocks.Sources.Pulse N(width=60, period=500)
"Heat pump control signal";
Modelica.Fluid.Sources.MassFlowSource_T loa1(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou1(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.Constant TLoa(k=285.15) "Load side fluid temperature";
Modelica.Blocks.Sources.Constant TSou(k=283.15)
"Source side fluid temperature";
Modelica.Blocks.Sources.RealExpression capErr(y=(heaPum1.QCon_flow -
scaling_factor*heaPum.QCon_flow)) "Apparent capacity of the heat pump";
Modelica.Blocks.Math.RealToInteger realToInteger;
Modelica.Blocks.Sources.RealExpression mLoa1(y=flowLoad)
"Load side mass flwo rate";
Modelica.Blocks.Sources.RealExpression mSou1(y=flowSource)
"Source side mass flow rate";
equation
connect(heaPum.port_a2, sou.ports[1]);
connect(heaPum.port_b1, sin1.ports[1]);
connect(heaPum.port_a1, loa.ports[1]);
connect(heaPum.port_b2, sin2.ports[1]);
connect(sin2.ports[2], heaPum1.port_b2);
connect(mLoa.y, loa1.m_flow_in);
connect(sou1.ports[1], heaPum1.port_a2);
connect(mSou.y, sou1.m_flow_in);
connect(TSou.y, sou1.T_in);
connect(sou.T_in, sou1.T_in);
connect(TLoa.y, loa1.T_in);
connect(TLoa.y, loa.T_in);
connect(loa1.ports[1], heaPum1.port_a1);
connect(heaPum1.port_b1, sin1.ports[2]);
connect(N.y, realToInteger.u);
connect(realToInteger.y, heaPum.stage);
connect(realToInteger.y, heaPum1.stage);
connect(mLoa1.y, loa.m_flow_in);
connect(mSou1.y, sou.m_flow_in);
end ReciprocatingWaterToWater_ScalingFactor;
Buildings.Fluid.HeatPumps.Validation.ReciprocatingWaterToWater_Static
Test model for static, reciprocating water to water heat pump
Information
Model that demonstrates the use of the Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heat pump model.
The heat pump power, condenser heat transfer rate and evaporator heat transfer rate are calculated for given water temperatures and flow rates on the evaporator and condenser sides.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 0.47 | Nominal mass flow rate on the condenser side [kg/s] |
| MassFlowRate | m2_flow_nominal | 0.47 | Nominal mass flow rate on the evaporator side [kg/s] |
| MassFlowRate | flowSource | 0.79 | Mass flow rate on the condenser side [kg/s] |
| MassFlowRate | flowLoad | 0.47 | Mass flow rate on the evaporator side [kg/s] |
Modelica definition
model ReciprocatingWaterToWater_Static
"Test model for static, reciprocating water to water heat pump"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=0.47
"Nominal mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate m2_flow_nominal=0.47
"Nominal mass flow rate on the evaporator side";
parameter Modelica.SIunits.MassFlowRate flowSource=0.79
"Mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate flowLoad=0.47
"Mass flow rate on the evaporator side";
Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heaPum(
per=Data.ReciprocatingWaterToWater.Generic(
etaEle=0.696,
PLos=100,
dTSup=9.82,
UACon=2210,
UAEva=1540,
pisDis=0.00162,
cleFac=0.069,
pDro=99290),
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=100,
dp2_nominal=100,
show_T=true,
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState,
enable_temperature_protection=false)
"Reciprocating water to water heat pump";
Buildings.Fluid.Sources.FixedBoundary sin2(redeclare package Medium = Medium2,
nPorts=1) "Source side sink";
Buildings.Fluid.Sources.FixedBoundary sin1(redeclare package Medium = Medium1,
nPorts=1) "Load side sink";
Modelica.Fluid.Sources.MassFlowSource_T loa(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Sourc side flow source";
Modelica.Blocks.Sources.RealExpression mLoa(y=flowLoad)
"Load side mass flow rate";
Modelica.Blocks.Sources.RealExpression mSou(y=flowSource)
"Source side mass flow rate";
Modelica.Blocks.Sources.Ramp yLoa(
height=20,
duration=750,
offset=293.15,
startTime=250) "Load side fluid temperature";
Modelica.Blocks.Sources.Ramp ySou(
height=20,
duration=750,
offset=283.15,
startTime=0) "Source side fluid temperature";
Modelica.Blocks.Sources.Constant isOn(k=1) "Heat pump control signal";
equation
connect(mSou.y, sou.m_flow_in);
connect(mLoa.y, loa.m_flow_in);
connect(yLoa.y, loa.T_in);
connect(ySou.y, sou.T_in);
connect(isOn.y, heaPum.y);
connect(loa.ports[1], heaPum.port_a1);
connect(heaPum.port_b1, sin1.ports[1]);
connect(heaPum.port_a2, sou.ports[1]);
connect(sin2.ports[1], heaPum.port_b2);
end ReciprocatingWaterToWater_Static;
Buildings.Fluid.HeatPumps.Validation.ReciprocatingWaterToWater_VariableSpeed
Test model for reciprocating water to water heat pump
Information
Model that demonstrates the use of the Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heat pump model.
With constant inlet source and load water temperatures, the compressor frequency is increased linearly to its full load value and then ramped down to zero.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 0.47 | Nominal mass flow rate on the condenser side [kg/s] |
| MassFlowRate | m2_flow_nominal | 0.47 | Nominal mass flow rate on the evaporator side [kg/s] |
| MassFlowRate | flowSource | 0.79 | Mass flow rate on the condenser side [kg/s] |
| MassFlowRate | flowLoad | 0.47 | Mass flow rate on the evaporator side [kg/s] |
Modelica definition
model ReciprocatingWaterToWater_VariableSpeed
"Test model for reciprocating water to water heat pump"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=0.47
"Nominal mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate m2_flow_nominal=0.47
"Nominal mass flow rate on the evaporator side";
parameter Modelica.SIunits.MassFlowRate flowSource=0.79
"Mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate flowLoad=0.47
"Mass flow rate on the evaporator side";
Buildings.Fluid.Sources.FixedBoundary sin2(redeclare package Medium = Medium2,
nPorts=1) "Source side sink";
Buildings.Fluid.Sources.FixedBoundary sin1(redeclare package Medium = Medium1,
nPorts=1) "Load side sink";
Modelica.Fluid.Sources.MassFlowSource_T loa(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.RealExpression mLoa(y=flowLoad)
"Load side mass flow rate";
Modelica.Blocks.Sources.RealExpression mSou(y=flowSource)
"Source side mass flow rate";
Buildings.Fluid.HeatPumps.ReciprocatingWaterToWater heaPum(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
show_T=true,
per=Buildings.Fluid.HeatPumps.Data.ReciprocatingWaterToWater.Generic(
etaEle=0.696,
PLos=100,
dTSup=9.82,
UACon=2210,
UAEva=1540,
pisDis=0.00162,
cleFac=0.069,
pDro=99290),
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
enable_temperature_protection=false)
"Reciprocating water to water heat pump";
Modelica.Blocks.Sources.Trapezoid N(
startTime=100,
offset=0.0,
rising=200,
width=200,
falling=200,
period=1000) "Heat pump control signal";
Modelica.Blocks.Sources.Constant TLoa(k=285.15) "Load side temperature";
Modelica.Blocks.Sources.Constant TSou(k=283.15) "Source side temeprature";
equation
connect(mSou.y, sou.m_flow_in);
connect(mLoa.y, loa.m_flow_in);
connect(N.y, heaPum.y);
connect(TSou.y, sou.T_in);
connect(TLoa.y, loa.T_in);
connect(sin2.ports[1], heaPum.port_b2);
connect(heaPum.port_a1, loa.ports[1]);
connect(heaPum.port_b1, sin1.ports[1]);
connect(sou.ports[1], heaPum.port_a2);
end ReciprocatingWaterToWater_VariableSpeed;
Buildings.Fluid.HeatPumps.Validation.ScrollWaterToWater_Dynamic
Test model for scroll water to water heat pump
Information
Model that demonstrates the use of the Buildings.Fluid.HeatPumps.ScrollWaterToWater heat pump model. This validation case also tests the stage input to the heat pump models.
With constant inlet source and load water temperatures, the heat pumps cycle on and off. The apparent capacity of the dynamic model is compared to the steady-state model and to the condenser heat transfer rate.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 0.47 | Nominal mass flow rate on the condenser side [kg/s] |
| MassFlowRate | m2_flow_nominal | 0.47 | Nominal mass flow rate on the evaporator side [kg/s] |
| MassFlowRate | flowSource | 0.79 | Mass flow rate on the condenser side [kg/s] |
| MassFlowRate | flowLoad | 0.47 | Mass flow rate on the evaporator side [kg/s] |
Modelica definition
model ScrollWaterToWater_Dynamic
"Test model for scroll water to water heat pump"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=0.47
"Nominal mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate m2_flow_nominal=0.47
"Nominal mass flow rate on the evaporator side";
parameter Modelica.SIunits.MassFlowRate flowSource=0.79
"Mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate flowLoad=0.47
"Mass flow rate on the evaporator side";
Buildings.Fluid.Sources.FixedBoundary sin2(redeclare package Medium = Medium2,
nPorts=2) "Source side sink";
Buildings.Fluid.Sources.FixedBoundary sin1(redeclare package Medium = Medium1,
nPorts=2) "Load side sink";
Modelica.Fluid.Sources.MassFlowSource_T loa(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.RealExpression mLoa(y=flowLoad)
"Load side mass flwo rate";
Modelica.Blocks.Sources.RealExpression mSou(y=flowSource)
"Source side mass flow rate";
Buildings.Fluid.HeatPumps.ScrollWaterToWater heaPum(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
enable_variable_speed=false,
datHeaPum(
etaEle=0.696,
PLos=500,
dTSup=10,
UACon=4400,
UAEva=4400,
volRat=2,
V_flow_nominal=0.003,
leaCoe=0.01),
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState,
enable_temperature_protection=false) "Scroll water to water heat pump";
Buildings.Fluid.HeatPumps.ScrollWaterToWater heaPum1(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyStateInitial,
tau1=15,
tau2=15,
enable_variable_speed=false,
datHeaPum(
etaEle=0.696,
PLos=500,
dTSup=10,
UACon=4400,
UAEva=4400,
volRat=2,
V_flow_nominal=0.003,
leaCoe=0.01),
enable_temperature_protection=false)
"Scroll water to water heat pump with transient effects";
Modelica.Blocks.Sources.Pulse N(width=60, period=500)
"Heat pump control signal";
Modelica.Fluid.Sources.MassFlowSource_T loa1(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou1(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.Constant TLoa(k=285.15) "Load side fluid temperature";
Modelica.Blocks.Sources.Constant TSou(k=283.15)
"Source side fluid temperature";
Modelica.Blocks.Sources.RealExpression appCap(y=heaPum1.port_a1.m_flow*(
heaPum1.port_b1.h_outflow - loa1.ports[1].h_outflow))
"Apparent capacity of the heat pump";
Modelica.Blocks.Math.RealToInteger realToInteger;
equation
connect(mSou.y, sou.m_flow_in);
connect(heaPum.port_a2, sou.ports[1]);
connect(heaPum.port_b1, sin1.ports[1]);
connect(heaPum.port_a1, loa.ports[1]);
connect(heaPum.port_b2, sin2.ports[1]);
connect(sin2.ports[2], heaPum1.port_b2);
connect(mLoa.y, loa.m_flow_in);
connect(mLoa.y, loa1.m_flow_in);
connect(sou1.ports[1], heaPum1.port_a2);
connect(mSou.y, sou1.m_flow_in);
connect(TSou.y, sou1.T_in);
connect(sou.T_in, sou1.T_in);
connect(TLoa.y, loa1.T_in);
connect(TLoa.y, loa.T_in);
connect(loa1.ports[1], heaPum1.port_a1);
connect(heaPum1.port_b1, sin1.ports[2]);
connect(N.y, realToInteger.u);
connect(realToInteger.y, heaPum.stage);
connect(realToInteger.y, heaPum1.stage);
end ScrollWaterToWater_Dynamic;
Buildings.Fluid.HeatPumps.Validation.ScrollWaterToWater_ScalingFactor
Test model for scroll water to water heat pump
Information
Model that demonstrates the use of the Buildings.Fluid.HeatPumps.ScrollWaterToWater heat pump model. This validation case also tests the stage input to the heat pump models.
With constant inlet source and load water temperatures, the heat pumps cycle on and off. The capacity of the scaled heat pump model is compared to the capacity of the non-scaled heat pump model.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 0.47 | Nominal mass flow rate on the condenser side [kg/s] |
| MassFlowRate | m2_flow_nominal | 0.47 | Nominal mass flow rate on the evaporator side [kg/s] |
| MassFlowRate | flowSource | 0.79 | Mass flow rate on the condenser side [kg/s] |
| MassFlowRate | flowLoad | 0.47 | Mass flow rate on the evaporator side [kg/s] |
| Real | scaling_factor | 2.41 | Scaling factor for heat pump capacity |
Modelica definition
model ScrollWaterToWater_ScalingFactor
"Test model for scroll water to water heat pump"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=0.47
"Nominal mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate m2_flow_nominal=0.47
"Nominal mass flow rate on the evaporator side";
parameter Modelica.SIunits.MassFlowRate flowSource=0.79
"Mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate flowLoad=0.47
"Mass flow rate on the evaporator side";
parameter Real scaling_factor=2.41 "Scaling factor for heat pump capacity";
Buildings.Fluid.Sources.FixedBoundary sin2(redeclare package Medium = Medium2,
nPorts=2) "Source side sink";
Buildings.Fluid.Sources.FixedBoundary sin1(redeclare package Medium = Medium1,
nPorts=2) "Load side sink";
Modelica.Fluid.Sources.MassFlowSource_T loa(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Buildings.Fluid.HeatPumps.ScrollWaterToWater heaPum(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
enable_variable_speed=false,
datHeaPum(
etaEle=0.696,
PLos=500,
dTSup=10,
UACon=4400,
UAEva=4400,
volRat=2,
V_flow_nominal=0.003,
leaCoe=0.01),
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
enable_temperature_protection=false) "Scroll water to water heat pump";
Buildings.Fluid.HeatPumps.ScrollWaterToWater heaPum1(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
enable_variable_speed=false,
m1_flow_nominal=m1_flow_nominal*scaling_factor,
m2_flow_nominal=m2_flow_nominal*scaling_factor,
scaling_factor=scaling_factor,
datHeaPum(
etaEle=0.696,
PLos=500,
dTSup=10,
UACon=4400,
UAEva=4400,
volRat=2,
V_flow_nominal=0.003,
leaCoe=0.01),
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
enable_temperature_protection=false)
"Scroll water to water heat pump with transient effects";
Modelica.Blocks.Sources.Pulse N(width=60, period=500)
"Heat pump control signal";
Modelica.Fluid.Sources.MassFlowSource_T loa1(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou1(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.Constant TLoa(k=285.15) "Load side fluid temperature";
Modelica.Blocks.Sources.Constant TSou(k=283.15)
"Source side fluid temperature";
Modelica.Blocks.Math.RealToInteger realToInteger;
Modelica.Blocks.Sources.RealExpression mSou(y=flowSource*scaling_factor)
"Source side mass flow rate";
Modelica.Blocks.Sources.RealExpression mLoa(y=flowLoad*scaling_factor)
"Load side mass flwo rate";
Modelica.Blocks.Sources.RealExpression mLoa1(y=flowLoad)
"Load side mass flwo rate";
Modelica.Blocks.Sources.RealExpression mSou1(y=flowSource)
"Source side mass flow rate";
Modelica.Blocks.Sources.RealExpression capErr(y=(heaPum1.QCon_flow -
scaling_factor*heaPum.QCon_flow)) "Apparent capacity of the heat pump";
equation
connect(heaPum.port_a2, sou.ports[1]);
connect(heaPum.port_b1, sin1.ports[1]);
connect(heaPum.port_a1, loa.ports[1]);
connect(heaPum.port_b2, sin2.ports[1]);
connect(sin2.ports[2], heaPum1.port_b2);
connect(sou1.ports[1], heaPum1.port_a2);
connect(TSou.y, sou1.T_in);
connect(sou.T_in, sou1.T_in);
connect(TLoa.y, loa1.T_in);
connect(TLoa.y, loa.T_in);
connect(loa1.ports[1], heaPum1.port_a1);
connect(heaPum1.port_b1, sin1.ports[2]);
connect(N.y, realToInteger.u);
connect(realToInteger.y, heaPum.stage);
connect(realToInteger.y, heaPum1.stage);
connect(mLoa.y, loa1.m_flow_in);
connect(mSou.y, sou1.m_flow_in);
connect(mSou1.y, sou.m_flow_in);
connect(mLoa1.y, loa.m_flow_in);
end ScrollWaterToWater_ScalingFactor;
Buildings.Fluid.HeatPumps.Validation.ScrollWaterToWater_Static
Test model for static scroll water to water heat pump
Information
Model that demonstrates the use of the Buildings.Fluid.HeatPumps.ScrollWaterToWater heat pump model.
The heat pump power, condenser heat transfer rate and evaporator heat transfer rate are calculated for given water temperatures and flow rates on the evaporator and condenser sides.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 0.47 | Nominal mass flow rate on the condenser side [kg/s] |
| MassFlowRate | m2_flow_nominal | 0.47 | Nominal mass flow rate on the evaporator side [kg/s] |
| MassFlowRate | flowSource | 0.79 | Mass flow rate on the condenser side [kg/s] |
| MassFlowRate | flowLoad | 0.47 | Mass flow rate on the evaporator side [kg/s] |
Modelica definition
model ScrollWaterToWater_Static
"Test model for static scroll water to water heat pump"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=0.47
"Nominal mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate m2_flow_nominal=0.47
"Nominal mass flow rate on the evaporator side";
parameter Modelica.SIunits.MassFlowRate flowSource=0.79
"Mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate flowLoad=0.47
"Mass flow rate on the evaporator side";
Buildings.Fluid.Sources.FixedBoundary sin2(redeclare package Medium = Medium2,
nPorts=1) "Source side sink";
Buildings.Fluid.Sources.FixedBoundary sin1(redeclare package Medium = Medium1,
nPorts=1) "Load side sink";
Modelica.Blocks.Sources.Constant isOn(k=1) "Heat pump control signal";
Modelica.Fluid.Sources.MassFlowSource_T loa(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.RealExpression mLoa(y=flowLoad)
"Load side mass flwo rate";
Modelica.Blocks.Sources.RealExpression mSou(y=flowSource)
"Source side mass flow rate";
Buildings.Fluid.HeatPumps.ScrollWaterToWater heaPum(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
show_T=true,
enable_variable_speed=true,
datHeaPum(
etaEle=0.696,
PLos=500,
dTSup=10,
UACon=4400,
UAEva=4400,
volRat=2,
V_flow_nominal=0.003,
leaCoe=0.01),
energyDynamics=Modelica.Fluid.Types.Dynamics.SteadyState,
enable_temperature_protection=false) "Scroll water to water heat pump";
Modelica.Blocks.Sources.Ramp yLoa(
height=20,
duration=750,
offset=293.15,
startTime=250) "Load side fluid temperature";
Modelica.Blocks.Sources.Ramp ySou(
height=20,
duration=750,
offset=283.15,
startTime=0) "Source side fluid temperature";
equation
connect(mSou.y, sou.m_flow_in);
connect(mLoa.y, loa.m_flow_in);
connect(yLoa.y, loa.T_in);
connect(ySou.y, sou.T_in);
connect(isOn.y, heaPum.y);
connect(sin2.ports[1], heaPum.port_b2);
connect(sou.ports[1], heaPum.port_a2);
connect(sin1.ports[1], heaPum.port_b1);
connect(loa.ports[1], heaPum.port_a1);
end ScrollWaterToWater_Static;
Buildings.Fluid.HeatPumps.Validation.ScrollWaterToWater_TemperatureProtection
Test model for temperature protection of scroll water to water heat pump
Information
Model that demonstrates the temperature protection implementation of the Buildings.Fluid.HeatPumps.ScrollWaterToWater heat pump model.
The heat pump is disabled when the evaporator and condenser temperature requirements are not satisfied.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 0.47 | Nominal mass flow rate on the condenser side [kg/s] |
| MassFlowRate | m2_flow_nominal | 0.47 | Nominal mass flow rate on the evaporator side [kg/s] |
| MassFlowRate | flowSource | 0.79 | Mass flow rate on the condenser side [kg/s] |
| MassFlowRate | flowLoad | 0.47 | Mass flow rate on the evaporator side [kg/s] |
Modelica definition
model ScrollWaterToWater_TemperatureProtection
"Test model for temperature protection of scroll water to water heat pump"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=0.47
"Nominal mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate m2_flow_nominal=0.47
"Nominal mass flow rate on the evaporator side";
parameter Modelica.SIunits.MassFlowRate flowSource=0.79
"Mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate flowLoad=0.47
"Mass flow rate on the evaporator side";
Buildings.Fluid.Sources.FixedBoundary sin2(redeclare package Medium = Medium2,
nPorts=1) "Source side sink";
Buildings.Fluid.Sources.FixedBoundary sin1(redeclare package Medium = Medium1,
nPorts=1) "Load side sink";
Modelica.Blocks.Sources.Constant isOn(k=1) "Heat pump control signal";
Modelica.Fluid.Sources.MassFlowSource_T loa(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.RealExpression mLoa(y=flowLoad)
"Load side mass flwo rate";
Modelica.Blocks.Sources.RealExpression mSou(y=flowSource)
"Source side mass flow rate";
Buildings.Fluid.HeatPumps.ScrollWaterToWater heaPum(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
show_T=true,
enable_variable_speed=true,
datHeaPum(
etaEle=0.696,
PLos=500,
dTSup=10,
UACon=4400,
UAEva=4400,
volRat=2,
V_flow_nominal=0.003,
leaCoe=0.01),
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
TConMax=273.15 + 60,
enable_temperature_protection=true) "Scroll water to water heat pump";
Modelica.Blocks.Sources.Sine yLoa(
startTime=250,
freqHz=1/600,
amplitude=30,
offset=313.15) "Load side fluid temperature";
Modelica.Blocks.Sources.Cosine ySou(
startTime=0,
amplitude=20,
offset=293.15,
freqHz=1/400) "Source side fluid temperature";
equation
connect(mSou.y, sou.m_flow_in);
connect(mLoa.y, loa.m_flow_in);
connect(yLoa.y, loa.T_in);
connect(ySou.y, sou.T_in);
connect(isOn.y, heaPum.y);
connect(sin2.ports[1], heaPum.port_b2);
connect(sou.ports[1], heaPum.port_a2);
connect(sin1.ports[1], heaPum.port_b1);
connect(loa.ports[1], heaPum.port_a1);
end ScrollWaterToWater_TemperatureProtection;
Buildings.Fluid.HeatPumps.Validation.ScrollWaterToWater_VariableSpeed
Test model for scroll water to water heat pump
Information
Model that demonstrates the use of the Buildings.Fluid.HeatPumps.ScrollWaterToWater heat pump model.
With constant inlet source and load water temperatures, the compressor frequency is increased linearly to its full load value.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 0.47 | Nominal mass flow rate on the condenser side [kg/s] |
| MassFlowRate | m2_flow_nominal | 0.47 | Nominal mass flow rate on the evaporator side [kg/s] |
| MassFlowRate | flowSource | 0.79 | Mass flow rate on the condenser side [kg/s] |
| MassFlowRate | flowLoad | 0.47 | Mass flow rate on the evaporator side [kg/s] |
Modelica definition
model ScrollWaterToWater_VariableSpeed
"Test model for scroll water to water heat pump"
extends Modelica.Icons.Example;
package Medium1 = Buildings.Media.Water "Medium model";
package Medium2 = Buildings.Media.Water "Medium model";
parameter Modelica.SIunits.MassFlowRate m1_flow_nominal=0.47
"Nominal mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate m2_flow_nominal=0.47
"Nominal mass flow rate on the evaporator side";
parameter Modelica.SIunits.MassFlowRate flowSource=0.79
"Mass flow rate on the condenser side";
parameter Modelica.SIunits.MassFlowRate flowLoad=0.47
"Mass flow rate on the evaporator side";
Buildings.Fluid.Sources.FixedBoundary sin2(redeclare package Medium = Medium2,
nPorts=1) "Source side sink";
Buildings.Fluid.Sources.FixedBoundary sin1(redeclare package Medium = Medium1,
nPorts=1) "Load side sink";
Modelica.Fluid.Sources.MassFlowSource_T loa(
redeclare package Medium = Medium1,
m_flow=flowLoad,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Load side flow source";
Modelica.Fluid.Sources.MassFlowSource_T sou(
redeclare package Medium = Medium2,
m_flow=flowSource,
use_m_flow_in=true,
use_T_in=true,
nPorts=1) "Source side flow source";
Modelica.Blocks.Sources.RealExpression mLoa(y=flowLoad)
"Load side mass flow rate";
Modelica.Blocks.Sources.RealExpression mSou(y=flowSource)
"Source side mass flwo rate";
Buildings.Fluid.HeatPumps.ScrollWaterToWater heaPum(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
dp1_nominal=1000,
dp2_nominal=1000,
redeclare package ref = Buildings.Media.Refrigerants.R410A,
show_T=true,
datHeaPum(
etaEle=0.696,
PLos=500,
dTSup=10,
UACon=4400,
UAEva=4400,
volRat=2,
V_flow_nominal=0.003,
leaCoe=0.01),
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
enable_temperature_protection=false) "Scroll water to water heat pump";
Modelica.Blocks.Sources.Ramp N(
duration=800,
startTime=100,
height=1.0,
offset=0.0) "Heat pump control signal";
Modelica.Blocks.Sources.Constant TLoa(k=285.15) "Load side fluid temperature";
Modelica.Blocks.Sources.Constant TSou(k=283.15)
"Source side fluid temperature";
equation
connect(mSou.y, sou.m_flow_in);
connect(mLoa.y, loa.m_flow_in);
connect(N.y, heaPum.y);
connect(TSou.y, sou.T_in);
connect(TLoa.y, loa.T_in);
connect(sin2.ports[1], heaPum.port_b2);
connect(loa.ports[1], heaPum.port_a1);
connect(heaPum.port_b1, sin1.ports[1]);
connect(heaPum.port_a2, sou.ports[1]);
end ScrollWaterToWater_VariableSpeed;