Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation
Collection of models that validate the Buildings.Applications.DataCenters.ChillerCooled package
Information
This package contains validation models for the classes in Buildings.Applications.DataCenters.ChillerCooled.Equipment.
Note that most validation models contain simple input data which may not be realistic, but for which the correct output can be obtained through an analytic solution. The examples plot various outputs, which have been verified against these solutions. These model outputs are stored as reference data and used for continuous validation whenever models in the library change.
Extends from Modelica.Icons.ExamplesPackage (Icon for packages containing runnable examples).
Package Content
| Name | Description |
|---|---|
 CoolingCoilHumidifyingHeating_ClosedLoop
|
Model of a air handling unit that tests temperature and humidity control |
| CoolingCoilHumidifyingHeating_OpenLoop
|
Model of a air handling unit that tests variable mass flow rates |
| ElectricHeater
|
Test model for ElectricHeater |
| HeatExchanger
|
Model that demonstrates use of a waterside economizer with outlet temperature control |
| HeatExchanger_ResetController
|
Model that demonstrates use of a waterside economizer with outlet temperature control and temperature controller is reset after a predefined time period |
| IntegratedPrimaryLoadSide
|
Integrated WSE on the load side in a primary-only chilled water system |
| IntegratedPrimaryPlantSide
|
Integrated WSE on the plant side in a primary-only chilled water system |
| IntegratedPrimarySecondary
|
Integrated WSE on the load side in a primary-secondary chilled water system |
| NonIntegrated
|
Non-integrated WSE in a chilled water system |
| WatersideEconomizer
|
Validate model Buildings.Applications.DataCenters.ChillerCooled.Equipment.WatersideEconomizer |
 BaseClasses
|
Package with base classes for Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation |
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.CoolingCoilHumidifyingHeating_ClosedLoop
Model of a air handling unit that tests temperature and humidity control
Information
This model demonstrates the use of Buildings.Applications.DataCenters.ChillerCooled.Equipment.CoolingCoilHumidifyingHeating. The valve on the water-side and the electric heater on the air-side is regulated to track a setpoint temperature for the air outlet based on the step changes in the inlet temperature on the waterside. The humidifier on the air-side is manipulated to control the humidity of the air outlet.
To avoid simultenous cooling (by opening the valve on the water side) and heating (by turning on the heater), a built-in controller is used to turn the reheater on and off. The detailed control logic can be found in Buildings.Applications.DataCenters.ChillerCooled.Controls.Reheat. A setting for this example is shown as following:
-
The switch point for the valve position,
yValSwiis set asyValSwi=yValMin + 0.1, and a deadband0.05is used. -
The switch point for the difference between the inlet temperature of
the reheater and the required outlet temperature setpoint,
dTSwiis set to 0, and deaband temperature difference 0.5 Kelvin is used.
Extends from Modelica.Icons.Example (Icon for runnable examples), Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialAirHandlerControl (Partial model for testing air hanlders with temperature and humidity control).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 2.9 | Nominal mass flow rate [kg/s] |
| MassFlowRate | m2_flow_nominal | 3.3 | Nominal mass flow rate [kg/s] |
| Temperature | T_a1_nominal | 6 + 273.15 | Nominal water inlet temperature [K] |
| Temperature | T_b1_nominal | 11 + 273.15 | Nominal water outlet temperature [K] |
| Temperature | T_a2_nominal | 26 + 273.15 | Nominal air inlet temperature [K] |
| Temperature | T_b2_nominal | 12 + 273.15 | Nominal air outlet temperature [K] |
| ThermalConductance | UA_nominal | m2_flow_nominal*1006*(T_b2_n... | Thermal conductance at nominal flow for sensible heat, used to compute time constant [W/K] |
| Real | yValMin | 0.4 | Minimum position of water-side valves |
Modelica definition
model CoolingCoilHumidifyingHeating_ClosedLoop
"Model of a air handling unit that tests temperature and humidity control"
extends Modelica.Icons.Example;
extends Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialAirHandlerControl
(
relHum(k=0.5),
sou_1(p=500000),
sou_2(nPorts = 1),
masFra(redeclare package Medium = Medium2),
TWat(
startTime=1200,
offset=273.15 + 13,
height=-6));
parameter Modelica.Units.SI.ThermalConductance UA_nominal=m2_flow_nominal*
1006*(T_b2_nominal - T_a2_nominal)/
Buildings.Fluid.HeatExchangers.BaseClasses.lmtd(
T_a1_nominal,
T_b1_nominal,
T_a2_nominal,
T_b2_nominal)
"Thermal conductance at nominal flow for sensible heat, used to compute time constant";
parameter Real yValMin = 0.4 "Minimum position of water-side valves";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.CoolingCoilHumidifyingHeating
ahu(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
allowFlowReversal1=true,
allowFlowReversal2=true,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
tauEleHea=1,
tauHum=1,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
UA_nominal=UA_nominal,
dpValve_nominal=6000,
mWatMax_flow=0.01,
perFan(pressure(V_flow=m2_flow_nominal*{0,0.5,1}, dp=300*{1.2,1.12,1})),
yValve_start=1,
dp1_nominal=3000,
dp2_nominal=200,
use_inputFilterValve=false,
QHeaMax_flow=10000,
yValSwi=yValMin + 0.1,
yValDeaBan=0.05)
"Air handling unit";
Modelica.Blocks.Sources.Constant uFan(k=1) "Control input for fan";
Modelica.Blocks.Sources.Constant masFraSet(k=0.011)
"Setpoint mass fraction";
Buildings.Controls.Continuous.LimPID PID(
yMax=1,
reverseActing=false,
Td=120,
yMin=yValMin,
k=0.5,
Ti=60)
"PID controller for the water-side valve in air handling units";
equation
connect(ahu.port_a2, sou_2.ports[1]);
connect(uFan.y, ahu.uFan);
connect(ahu.port_b2, temSenAir2.port_a);
connect(temSenWat1.port_b, ahu.port_a1);
connect(TSet.y, PID.u_s);
connect(temSenAir2.T, PID.u_m);
connect(PID.y, ahu.uVal);
connect(masFraSet.y, ahu.XSet_w);
connect(TSet.y, ahu.TSet);
connect(ahu.port_b1, temSenWat2.port_a);
end CoolingCoilHumidifyingHeating_ClosedLoop;
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.CoolingCoilHumidifyingHeating_OpenLoop
Model of a air handling unit that tests variable mass flow rates
Information
This model demonstrates the use of Buildings.Applications.DataCenters.ChillerCooled.Equipment.CoolingCoilHumidifyingHeating for different inlet conditions.
Extends from Modelica.Icons.Example (Icon for runnable examples), Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialAirHandlerMassFlow (Partial model for testing air handler at variable mass flowrate).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 2.9 | Nominal mass flow rate [kg/s] |
| MassFlowRate | m2_flow_nominal | 3.3 | Nominal mass flow rate [kg/s] |
| Temperature | T_a1_nominal | 6 + 273.15 | Nominal water inlet temperature [K] |
| Temperature | T_b1_nominal | 11 + 273.15 | Nominal water outlet temperature [K] |
| Temperature | T_a2_nominal | 26 + 273.15 | Nominal air inlet temperature [K] |
| Temperature | T_b2_nominal | 12 + 273.15 | Nominal air outlet temperature [K] |
| ThermalConductance | UA_nominal | m2_flow_nominal*1006*(12 - 2... | Thermal conductance at nominal flow for sensible heat, used to compute time constant [W/K] |
| Real | yValMin | 0.4 | Minimum position of water-side valves |
Modelica definition
model CoolingCoilHumidifyingHeating_OpenLoop
"Model of a air handling unit that tests variable mass flow rates"
extends Modelica.Icons.Example;
extends Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialAirHandlerMassFlow
( sou_2(nPorts=1), relHum(k=0.5));
parameter Modelica.Units.SI.ThermalConductance UA_nominal=m2_flow_nominal*
1006*(12 - 26)/Buildings.Fluid.HeatExchangers.BaseClasses.lmtd(
T_a1_nominal,
T_b1_nominal,
T_a2_nominal,
T_b2_nominal)
"Thermal conductance at nominal flow for sensible heat, used to compute time constant";
parameter Real yValMin = 0.4 "Minimum position of water-side valves";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.CoolingCoilHumidifyingHeating
ahu(
redeclare package Medium1 = Medium1,
redeclare package Medium2 = Medium2,
allowFlowReversal1=true,
allowFlowReversal2=true,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
yValve_start=0.2,
tauEleHea=1,
tauHum=1,
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
UA_nominal=UA_nominal,
dpValve_nominal=6000,
QHeaMax_flow=10000,
mWatMax_flow=0.01,
perFan(pressure(V_flow=m2_flow_nominal*{0,0.5,1}, dp=300*{1.2,1.12,1})),
dp1_nominal=3000,
dp2_nominal=200,
yValSwi=yValMin+0.05)
"Air handling unit";
Buildings.Fluid.Sensors.RelativeHumidityTwoPort senRelHum(
redeclare package Medium = Medium2, m_flow_nominal=m2_flow_nominal)
"Sensor for relative humidity";
Modelica.Blocks.Sources.Constant uVal(k=0.2)
"Control signal for water valve";
Modelica.Blocks.Sources.Constant temSet(k=15 + 273.15)
"Temperature setpoint ";
Modelica.Blocks.Sources.Constant XSet(k=0.01) "Mass fraction set point";
Modelica.Blocks.Sources.Constant uFan(k=1) "Control input for fan";
equation
connect(ahu.port_a2, sou_2.ports[1]);
connect(ahu.port_b2, senRelHum.port_a);
connect(uVal.y, ahu.uVal);
connect(uFan.y, ahu.uFan);
connect(temSet.y, ahu.TSet);
connect(XSet.y, ahu.XSet_w);
connect(temSenAir2.port_a, senRelHum.port_b);
connect(temSenWat1.port_b, ahu.port_a1);
connect(temSenWat2.port_a, ahu.port_b1);
end CoolingCoilHumidifyingHeating_OpenLoop;
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.ElectricHeater
Test model for ElectricHeater
Information
This model test the electric heater model: Buildings.Applications.DataCenters.ChillerCooled.Equipment.ElectricHeater.Extends from Modelica.Icons.Example (Icon for runnable examples), Buildings.Fluid.HeatExchangers.Examples.BaseClasses.Heater (Base class for example model for the heater and cooler).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| replaceable package Medium | PartialMedium | Medium model | |
| Volume | V | 6*6*2.7 | Volume [m3] |
| MassFlowRate | m_flow_nominal | V*1.2*6/3600 | Nominal mass flow rate [kg/s] |
| HeatFlowRate | Q_flow_nominal | 30*6*6 | Nominal heat loss of the room [W] |
Connectors
| Type | Name | Description |
|---|---|---|
| replaceable package Medium | Medium model | |
Modelica definition
model ElectricHeater "Test model for ElectricHeater"
extends Modelica.Icons.Example;
extends Buildings.Fluid.HeatExchangers.Examples.BaseClasses.Heater(
redeclare package Medium = Buildings.Media.Air,
m_flow_nominal=V*1.2*6/3600,
Q_flow_nominal=30*6*6,
mov(nominalValuesDefineDefaultPressureCurve=true,
dp_nominal=1200));
Buildings.Applications.DataCenters.ChillerCooled.Equipment.ElectricHeater eleHea(
redeclare package Medium = Medium,
m_flow_nominal=m_flow_nominal,
QMax_flow=Q_flow_nominal,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
dp_nominal=1000,
eta=0.95)
"Electric heater";
Buildings.Controls.SetPoints.Table tab(table=[0,273.15 + 15; 1,273.15 + 30])
"Temperature set point";
Modelica.Blocks.Sources.BooleanStep uHea(startTime(displayUnit="min") = 60000)
"On/off signal";
equation
connect(mov.port_b, eleHea.port_a);
connect(eleHea.port_b, THeaOut.port_a);
connect(conPI.y, tab.u);
connect(tab.y, eleHea.TSet);
connect(uHea.y, eleHea.on);
end ElectricHeater;
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.HeatExchanger
Model that demonstrates use of a waterside economizer with outlet temperature control
Information
This example demonstrates how the parameter use_controller influences
the temperautre at port_b2. The temperature at port_b2
can be controlled in hex1 where the controller is activated.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 1000*0.01035 | Nominal mass flow rate at evaporator [kg/s] |
| MassFlowRate | m2_flow_nominal | 1000*0.01035 | Nominal mass flow rate at condenser [kg/s] |
| Pressure | dp1_nominal | 60000 | Nominal pressure difference on medium 1 side [Pa] |
| Pressure | dp2_nominal | 60000 | Nominal pressure difference on medium 2 side [Pa] |
Modelica definition
model HeatExchanger
"Model that demonstrates use of a waterside economizer with outlet temperature control"
extends Modelica.Icons.Example;
package MediumW = Buildings.Media.Water "Medium model";
parameter Modelica.Units.SI.MassFlowRate m1_flow_nominal=1000*0.01035
"Nominal mass flow rate at evaporator";
parameter Modelica.Units.SI.MassFlowRate m2_flow_nominal=1000*0.01035
"Nominal mass flow rate at condenser";
parameter Modelica.Units.SI.Pressure dp1_nominal=60000
"Nominal pressure difference on medium 1 side";
parameter Modelica.Units.SI.Pressure dp2_nominal=60000
"Nominal pressure difference on medium 2 side";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.HeatExchanger_TSet
hex1(
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
eta=0.8,
dp1_nominal=dp1_nominal,
dp2_nominal=dp2_nominal,
T_start=273.15 + 10,
use_controller=true,
redeclare package Medium1 = MediumW,
redeclare package Medium2 = MediumW,
Ti=40,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
k=0.1,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial)
"Water-to-water heat exchanger with built-in PID controller to control the temperature at port_b2";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.HeatExchanger_TSet
hex2(
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
eta=0.8,
dp1_nominal=dp1_nominal,
dp2_nominal=dp2_nominal,
T_start=273.15 + 10,
redeclare package Medium1 = MediumW,
redeclare package Medium2 = MediumW,
use_controller=false)
"Water-to-water heat exchanger without built-in controllers to control the temperature at port_b2";
Buildings.Fluid.Sources.Boundary_pT sin1(
nPorts=2,
redeclare package Medium = MediumW)
"Sink on medium 1 side";
Buildings.Fluid.Sources.MassFlowSource_T sou1(
use_T_in=true,
nPorts=2,
redeclare package Medium = MediumW,
m_flow=2*m1_flow_nominal,
T=298.15)
"Source on medium 1 side";
Modelica.Blocks.Sources.TimeTable TCon_in(
table=[0,273.15 + 12.78;
7200,273.15 + 12.78;
7200,273.15 + 18.33;
14400,273.15 + 18.33;
14400,273.15 + 26.67],
offset=0,
startTime=0)
"Condenser inlet temperature";
Buildings.Fluid.Sources.Boundary_pT sin2(
nPorts=2,
redeclare package Medium = MediumW)
"Sink on medium 2 side";
Buildings.Fluid.Sources.MassFlowSource_T sou2_2(
nPorts=1,
redeclare package Medium = MediumW,
m_flow=m2_flow_nominal,
use_T_in=true)
"Source on medium 2 side";
Modelica.Blocks.Sources.Constant TEva_in(k=273.15 + 25.28)
"Evaporator inlet temperature";
Buildings.Fluid.Sensors.TemperatureTwoPort TSen1(
m_flow_nominal=m2_flow_nominal,
redeclare package Medium = MediumW)
"Temperature sensor";
Buildings.Fluid.Sensors.TemperatureTwoPort TSen2(
redeclare package Medium = MediumW,
m_flow_nominal=m2_flow_nominal)
"Temperature sensor";
Modelica.Blocks.Sources.Constant TSet(
k(unit="K",displayUnit="degC")=273.15+16.56)
"Leaving chilled water temperature setpoint";
Buildings.Fluid.Sources.MassFlowSource_T sou2_1(
nPorts=1,
redeclare package Medium = MediumW,
m_flow=m2_flow_nominal,
use_T_in=true)
"Source on medium 2 side";
Modelica.Blocks.Sources.Constant TEva_in1( k=273.15 + 25.28)
"Evaporator inlet temperature";
equation
connect(TSet.y, hex1.TSet);
connect(sou1.ports[1], hex1.port_a1);
connect(hex1.port_b1, sin1.ports[1]);
connect(TCon_in.y,sou1. T_in);
connect(sou2_2.T_in, TEva_in.y);
connect(hex1.port_b2, TSen1.port_a);
connect(TSen1.port_b, sin2.ports[1]);
connect(sou1.ports[2], hex2.port_a1);
connect(hex2.port_b2, TSen2.port_a);
connect(TSen2.port_b, sin2.ports[2]);
connect(hex2.port_b1, sin1.ports[2]);
connect(hex2.port_a2, sou2_2.ports[1]);
connect(hex1.port_a2, sou2_1.ports[1]);
connect(TEva_in1.y, sou2_1.T_in);
end HeatExchanger;
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.HeatExchanger_ResetController
Model that demonstrates use of a waterside economizer with outlet temperature control and temperature controller is reset after a predefined time period
Information
This example demonstrates how the PID controller in the heat exchanger model can be reset. We compared three options: (1) reset with a paramter value; (2) reset with an input signal; (3) without reset.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | m1_flow_nominal | 1000*0.01035 | Nominal mass flow rate at evaporator [kg/s] |
| MassFlowRate | m2_flow_nominal | 1000*0.01035 | Nominal mass flow rate at condenser [kg/s] |
| Pressure | dp1_nominal | 60000 | Nominal pressure difference on medium 1 side [Pa] |
| Pressure | dp2_nominal | 60000 | Nominal pressure difference on medium 2 side [Pa] |
Modelica definition
model HeatExchanger_ResetController
"Model that demonstrates use of a waterside economizer with outlet temperature control and temperature controller is reset after a predefined time period"
extends Modelica.Icons.Example;
package MediumW = Buildings.Media.Water "Medium model";
parameter Modelica.Units.SI.MassFlowRate m1_flow_nominal=1000*0.01035
"Nominal mass flow rate at evaporator";
parameter Modelica.Units.SI.MassFlowRate m2_flow_nominal=1000*0.01035
"Nominal mass flow rate at condenser";
parameter Modelica.Units.SI.Pressure dp1_nominal=60000
"Nominal pressure difference on medium 1 side";
parameter Modelica.Units.SI.Pressure dp2_nominal=60000
"Nominal pressure difference on medium 2 side";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.HeatExchanger_TSet
hex1(
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
eta=0.8,
dp1_nominal=dp1_nominal,
dp2_nominal=dp2_nominal,
T_start=273.15 + 10,
use_controller=true,
redeclare package Medium1 = MediumW,
redeclare package Medium2 = MediumW,
Ti=40,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
k=0.1,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
reset=Buildings.Types.Reset.Parameter,
y_reset=0)
"Water-to-water heat exchanger with built-in PID controller to control the temperature at port_b2";
Buildings.Fluid.Sources.Boundary_pT sin1(
nPorts=3,
redeclare package Medium = MediumW)
"Sink on medium 1 side";
Fluid.Sources.Boundary_pT sou1(
p=MediumW.p_default + 60E3,
use_T_in=true,
nPorts=3,
redeclare package Medium = MediumW,
T=298.15)
"Source on medium 1 side";
Modelica.Blocks.Sources.TimeTable TCon_in(
table=[0,273.15 + 12.78;
7200,273.15 + 12.78;
7200,273.15 + 18.33;
14400,273.15 + 18.33;
14400,273.15 + 26.67],
offset=0,
startTime=0)
"Condenser inlet temperature";
Buildings.Fluid.Sources.Boundary_pT sin2(
nPorts=3,
redeclare package Medium = MediumW)
"Sink on medium 2 side";
Buildings.Fluid.Sensors.TemperatureTwoPort TSen1(
m_flow_nominal=m2_flow_nominal,
redeclare package Medium = MediumW)
"Temperature sensor";
Buildings.Fluid.Sensors.TemperatureTwoPort TSen2(
redeclare package Medium = MediumW,
m_flow_nominal=m2_flow_nominal)
"Temperature sensor";
Modelica.Blocks.Sources.Constant TSet(
k(unit="K",displayUnit="degC")=273.15+16.56)
"Leaving chilled water temperature setpoint";
Fluid.Sources.Boundary_pT sou2_1(
p=MediumW.p_default + 50E3,
nPorts=3,
redeclare package Medium = MediumW,
use_T_in=true)
"Source on medium 2 side";
Modelica.Blocks.Sources.Constant TEva_in(k=273.15 + 25.28)
"Evaporator inlet temperature";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.HeatExchanger_TSet
hex2(
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
eta=0.8,
dp1_nominal=dp1_nominal,
dp2_nominal=dp2_nominal,
T_start=273.15 + 10,
use_controller=true,
redeclare package Medium1 = MediumW,
redeclare package Medium2 = MediumW,
Ti=40,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
k=0.1,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
reset=Buildings.Types.Reset.Input)
"Water-to-water heat exchanger with built-in PID controller to control the temperature at port_b2";
Modelica.Blocks.Sources.BooleanPulse tri(period=900)
"Trigger controller reset";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.HeatExchanger_TSet
hex3(
m1_flow_nominal=m1_flow_nominal,
m2_flow_nominal=m2_flow_nominal,
eta=0.8,
dp1_nominal=dp1_nominal,
dp2_nominal=dp2_nominal,
T_start=273.15 + 10,
use_controller=true,
redeclare package Medium1 = MediumW,
redeclare package Medium2 = MediumW,
Ti=40,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
k=0.1,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial)
"Water-to-water heat exchanger with built-in PID controller to control the temperature at port_b2";
Buildings.Fluid.Sensors.TemperatureTwoPort TSen3(redeclare package Medium =
MediumW, m_flow_nominal=m2_flow_nominal)
"Temperature sensor";
Modelica.Blocks.Sources.Constant yRes(k=0) "Reset integrator signal";
equation
connect(TSet.y, hex1.TSet);
connect(sou1.ports[1], hex1.port_a1);
connect(hex1.port_b1, sin1.ports[1]);
connect(TCon_in.y,sou1. T_in);
connect(hex1.port_b2, TSen1.port_a);
connect(TSen1.port_b, sin2.ports[1]);
connect(TSen2.port_b, sin2.ports[2]);
connect(hex1.port_a2, sou2_1.ports[1]);
connect(TEva_in.y, sou2_1.T_in);
connect(TSen2.port_a, hex2.port_b2);
connect(sou1.ports[2], hex2.port_a1);
connect(hex2.port_b1, sin1.ports[2]);
connect(TSet.y, hex2.TSet);
connect(tri.y, hex1.trigger);
connect(sou2_1.ports[2], hex2.port_a2);
connect(sin2.ports[3], TSen3.port_b);
connect(TSen3.port_a, hex3.port_b2);
connect(hex3.port_a1, sou1.ports[3]);
connect(hex3.port_b1, sin1.ports[3]);
connect(hex3.port_a2, sou2_1.ports[3]);
connect(TSet.y, hex3.TSet);
connect(tri.y, hex2.trigger);
connect(yRes.y, hex2.y_reset_in);
end HeatExchanger_ResetController;
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.IntegratedPrimaryLoadSide
Integrated WSE on the load side in a primary-only chilled water system
Information
This example demonstrates how the model responses according to different cooling mode signals (free cooling mode, partially mechanical cooling and fully mechanical cooling).
The reponses are also compared with a second case where the PI controller in the WSE is reset every 1800s.
Extends from Modelica.Icons.Example (Icon for runnable examples), Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialPlant (Partial examples for Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | mCHW_flow_nominal | 2567.1*1000/(4200*10) | Nominal mass flow rate at chilled water [kg/s] |
| MassFlowRate | mCW_flow_nominal | 2567.1*1000/(4200*8.5) | Nominal mass flow rate at condenser water [kg/s] |
| PressureDifference | dpCHW_nominal | 40000 | Nominal pressure [Pa] |
| PressureDifference | dpCW_nominal | 40000 | Nominal pressure [Pa] |
| Integer | numChi | 1 | Number of chillers |
| Generic | perPum[numChi] | perPum(each pressure=Buildin... | Pump performance data |
Modelica definition
model IntegratedPrimaryLoadSide
"Integrated WSE on the load side in a primary-only chilled water system"
extends Modelica.Icons.Example;
extends Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialPlant
(
sou1(nPorts=2),
sin1(nPorts=2),
TSet(k=273.15 + 5.56),
TEva_in(k=273.15 + 15.28),
sin2(nPorts=2));
Buildings.Applications.DataCenters.ChillerCooled.Equipment.IntegratedPrimaryLoadSide
intWSEPri1(
m1_flow_chi_nominal=mCW_flow_nominal,
m2_flow_chi_nominal=mCHW_flow_nominal,
m1_flow_wse_nominal=mCW_flow_nominal,
m2_flow_wse_nominal=mCHW_flow_nominal,
redeclare package Medium1 = MediumCW,
redeclare package Medium2 = MediumCHW,
dp1_chi_nominal=dpCW_nominal,
dp1_wse_nominal=dpCW_nominal,
dp2_chi_nominal=dpCHW_nominal,
dp2_wse_nominal=dpCHW_nominal,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
redeclare Buildings.Fluid.Chillers.Data.ElectricEIR.ElectricEIRChiller_Trane_CVHF_2567kW_11_77COP_VSD
perChi,
k=0.4,
Ti=80,
perPum=perPum,
numChi=numChi,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial)
"Integrated waterside economizer on the load side of the primary-only chilled water system";
Modelica.Blocks.Sources.Constant yPum(k=1)
"Conrol signal for pumps";
Modelica.Blocks.Sources.RealExpression yVal5(
y=if onChi.y and not onWSE.y then 1 else 0)
"On/off signal for valve 5";
Modelica.Blocks.Sources.RealExpression yVal6(
y=if not onChi.y and onWSE.y then 1 else 0)
"On/off signal for valve 6";
Buildings.Fluid.Sources.Boundary_pT sou2(
redeclare package Medium = MediumCHW,
nPorts=2,
use_T_in=true) "Source on medium 2 side";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.IntegratedPrimaryLoadSide
intWSEPri2(
m1_flow_chi_nominal=mCW_flow_nominal,
m2_flow_chi_nominal=mCHW_flow_nominal,
m1_flow_wse_nominal=mCW_flow_nominal,
m2_flow_wse_nominal=mCHW_flow_nominal,
redeclare package Medium1 = MediumCW,
redeclare package Medium2 = MediumCHW,
dp1_chi_nominal=dpCW_nominal,
dp1_wse_nominal=dpCW_nominal,
dp2_chi_nominal=dpCHW_nominal,
dp2_wse_nominal=dpCHW_nominal,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
redeclare Buildings.Fluid.Chillers.Data.ElectricEIR.ElectricEIRChiller_Trane_CVHF_2567kW_11_77COP_VSD
perChi,
k=0.4,
Ti=80,
perPum=perPum,
numChi=numChi,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
reset=Buildings.Types.Reset.Parameter,
y_reset=0)
"Integrated waterside economizer on the load side of the primary-only chilled water system with PI controller reset";
Buildings.Fluid.Sensors.TemperatureTwoPort TSup2(
redeclare package Medium = MediumCHW,
m_flow_nominal=mCHW_flow_nominal);
Modelica.Blocks.Sources.BooleanPulse tri(period=1800)
"Trigger controller reset";
parameter Fluid.Movers.Data.Generic[numChi] perPum(each pressure=
Buildings.Fluid.Movers.BaseClasses.Characteristics.flowParameters(
V_flow=mCHW_flow_nominal/1000*{0.2,0.6,1.0,1.2}, dp=dpCHW_nominal*{1.2,1.1,
1.0,0.6})) "Pump performance data";
equation
connect(TSet.y, intWSEPri1.TSet);
connect(yVal5.y, intWSEPri1.yVal5);
connect(yVal6.y, intWSEPri1.yVal6);
connect(yPum.y, intWSEPri1.yPum[1]);
connect(intWSEPri1.port_a1, sou1.ports[1]);
connect(intWSEPri1.port_b2, TSup1.port_a);
connect(intWSEPri1.port_b1, sin1.ports[1]);
connect(intWSEPri1.port_a2, sou2.ports[1]);
connect(TEva_in.y, sou2.T_in);
connect(TSup2.port_a, intWSEPri2.port_b2);
connect(intWSEPri2.port_a2, sou2.ports[2]);
connect(intWSEPri2.port_b1, sin1.ports[2]);
connect(intWSEPri2.port_a1, sou1.ports[2]);
connect(TSup2.port_b, sin2.ports[2]);
connect(TSet.y, intWSEPri2.TSet);
connect(yVal5.y, intWSEPri2.yVal5);
connect(yVal6.y, intWSEPri2.yVal6);
connect(yPum.y, intWSEPri2.yPum[1]);
connect(tri.y, intWSEPri2.trigger);
connect(intWSEPri2.on[1], onChi.y);
connect(intWSEPri2.on[2], onWSE.y);
connect(intWSEPri1.on[1], onChi.y);
connect(intWSEPri1.on[2], onWSE.y);
end IntegratedPrimaryLoadSide;
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.IntegratedPrimaryPlantSide
Integrated WSE on the plant side in a primary-only chilled water system
Information
This example demonstrates how the model responses according to different cooling mode signals (free cooling mode, partially mechanical cooling and fully mechanical cooling).
The reponses are also compared with a second case where the PI controller in the WSE is reset every 1800s.
Extends from Modelica.Icons.Example (Icon for runnable examples), Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialPlant (Partial examples for Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | mCHW_flow_nominal | 2567.1*1000/(4200*10) | Nominal mass flow rate at chilled water [kg/s] |
| MassFlowRate | mCW_flow_nominal | 2567.1*1000/(4200*8.5) | Nominal mass flow rate at condenser water [kg/s] |
| PressureDifference | dpCHW_nominal | 40000 | Nominal pressure [Pa] |
| PressureDifference | dpCW_nominal | 40000 | Nominal pressure [Pa] |
| Integer | numChi | 1 | Number of chillers |
Modelica definition
model IntegratedPrimaryPlantSide
"Integrated WSE on the plant side in a primary-only chilled water system"
extends Modelica.Icons.Example;
extends Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialPlant
(
sou1(nPorts=2),
sin1(nPorts=2),
TSet(k=273.15 + 5.56),
TEva_in(k=273.15 + 15.28),
sin2(nPorts=2));
Buildings.Applications.DataCenters.ChillerCooled.Equipment.IntegratedPrimaryPlantSide
intWSEPri1(
m1_flow_chi_nominal=mCW_flow_nominal,
m2_flow_chi_nominal=mCHW_flow_nominal,
m1_flow_wse_nominal=mCW_flow_nominal,
m2_flow_wse_nominal=mCHW_flow_nominal,
redeclare package Medium1 = MediumCW,
redeclare package Medium2 = MediumCHW,
dp1_chi_nominal=dpCW_nominal,
dp1_wse_nominal=dpCW_nominal,
dp2_chi_nominal=dpCHW_nominal,
dp2_wse_nominal=dpCHW_nominal,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
redeclare Buildings.Fluid.Chillers.Data.ElectricEIR.ElectricEIRChiller_Trane_CVHF_2567kW_11_77COP_VSD
perChi,
k=0.4,
Ti=80,
numChi=numChi,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial)
"Integrated waterside economizer in the primary-only chilled water system";
Modelica.Blocks.Sources.RealExpression yVal5(
y=if onChi.y and not onWSE.y then 1 else 0)
"On/off signal for valve 5";
Modelica.Blocks.Sources.RealExpression yVal6(
y=if not onChi.y and onWSE.y then 1 else 0)
"On/off signal for valve 6";
Fluid.Sources.Boundary_pT sou2(
redeclare package Medium = MediumCHW,
p=MediumCHW.p_default + 1E5,
nPorts=2,
use_T_in=true) "Source on medium 2 side";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.IntegratedPrimaryPlantSide
intWSEPri2(
m1_flow_chi_nominal=mCW_flow_nominal,
m2_flow_chi_nominal=mCHW_flow_nominal,
m1_flow_wse_nominal=mCW_flow_nominal,
m2_flow_wse_nominal=mCHW_flow_nominal,
redeclare package Medium1 = MediumCW,
redeclare package Medium2 = MediumCHW,
dp1_chi_nominal=dpCW_nominal,
dp1_wse_nominal=dpCW_nominal,
dp2_chi_nominal=dpCHW_nominal,
dp2_wse_nominal=dpCHW_nominal,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
redeclare Buildings.Fluid.Chillers.Data.ElectricEIR.ElectricEIRChiller_Trane_CVHF_2567kW_11_77COP_VSD
perChi,
k=0.4,
Ti=80,
numChi=numChi,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
reset=Buildings.Types.Reset.Parameter,
y_reset=0)
"Integrated waterside economizer in the primary-only chilled water system";
Modelica.Blocks.Sources.BooleanPulse tri(period=1800)
"Trigger controller reset";
Buildings.Fluid.Sensors.TemperatureTwoPort TSup2(redeclare package Medium =
MediumCHW, m_flow_nominal=mCHW_flow_nominal) "Temperature sensor";
equation
connect(yVal5.y, intWSEPri1.yVal5);
connect(yVal6.y, intWSEPri1.yVal6);
connect(intWSEPri1.port_a1, sou1.ports[1]);
connect(intWSEPri1.port_b2, TSup1.port_a);
connect(intWSEPri1.port_b1, sin1.ports[1]);
connect(intWSEPri1.port_a2, sou2.ports[1]);
connect(TEva_in.y, sou2.T_in);
connect(TSet.y, intWSEPri1.TSet);
connect(onChi.y, intWSEPri1.on[1]);
connect(onWSE.y, intWSEPri1.on[2]);
connect(sou1.ports[2], intWSEPri2.port_a1);
connect(sou2.ports[2], intWSEPri2.port_a2);
connect(intWSEPri2.port_b1, sin1.ports[2]);
connect(TSet.y, intWSEPri2.TSet);
connect(onChi.y, intWSEPri2.on[1]);
connect(onWSE.y, intWSEPri2.on[2]);
connect(yVal5.y, intWSEPri2.yVal5);
connect(yVal6.y, intWSEPri2.yVal6);
connect(tri.y, intWSEPri2.trigger);
connect(sin2.ports[2], TSup2.port_b);
connect(TSup2.port_a, intWSEPri2.port_b2);
end IntegratedPrimaryPlantSide;
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.IntegratedPrimarySecondary
Integrated WSE on the load side in a primary-secondary chilled water system
Information
This example demonstrates how the model responses according to different cooling mode signals (free cooling mode, partially mechanical cooling and fully mechanical cooling).
The reponses are also compared with a second case where the PI controller in the WSE is reset every 1800s.
Extends from Modelica.Icons.Example (Icon for runnable examples), Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialPlant (Partial examples for Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | mCHW_flow_nominal | 2567.1*1000/(4200*10) | Nominal mass flow rate at chilled water [kg/s] |
| MassFlowRate | mCW_flow_nominal | 2567.1*1000/(4200*8.5) | Nominal mass flow rate at condenser water [kg/s] |
| PressureDifference | dpCHW_nominal | 40000 | Nominal pressure [Pa] |
| PressureDifference | dpCW_nominal | 40000 | Nominal pressure [Pa] |
| Integer | numChi | 1 | Number of chillers |
| Generic | perPum[numChi] | perPum(each pressure=Buildin... | Pump performance data |
Modelica definition
model IntegratedPrimarySecondary
"Integrated WSE on the load side in a primary-secondary chilled water system"
extends Modelica.Icons.Example;
extends Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialPlant
(
sou1(nPorts=2),
sin1(nPorts=2),
TSet(k=273.15 + 5.56),
TEva_in(k=273.15 + 10.28),
sin2(nPorts=2));
Buildings.Applications.DataCenters.ChillerCooled.Equipment.IntegratedPrimarySecondary
intWSEPriSec1(
m1_flow_chi_nominal=mCW_flow_nominal,
m2_flow_chi_nominal=mCHW_flow_nominal,
m1_flow_wse_nominal=mCW_flow_nominal,
m2_flow_wse_nominal=mCHW_flow_nominal,
redeclare package Medium1 = MediumCW,
redeclare package Medium2 = MediumCHW,
dp1_chi_nominal=dpCW_nominal,
dp1_wse_nominal=dpCW_nominal,
dp2_chi_nominal=dpCHW_nominal,
dp2_wse_nominal=dpCHW_nominal,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
redeclare Buildings.Fluid.Chillers.Data.ElectricEIR.ElectricEIRChiller_Trane_CVHF_2567kW_11_77COP_VSD
perChi,
k=0.4,
Ti=80,
numChi=numChi,
perPum=perPum,
addPowerToMedium=false,
show_T=true,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial)
"Integrated waterside economizer on the load side of a primary-secondary chilled water system";
Modelica.Blocks.Sources.RealExpression yVal5(
y=if onChi.y and not onWSE.y then 1 else 0)
"On/off signal for valve 5";
Modelica.Blocks.Sources.RealExpression yPum(y=if onChi.y then 1 else 0)
"Input signal for primary pump";
Fluid.Sources.Boundary_pT sou2(
redeclare package Medium = MediumCHW,
p=MediumCHW.p_default + 30E3,
nPorts=2,
use_T_in=true) "Source on medium 2 side";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.IntegratedPrimarySecondary
intWSEPriSec2(
m1_flow_chi_nominal=mCW_flow_nominal,
m2_flow_chi_nominal=mCHW_flow_nominal,
m1_flow_wse_nominal=mCW_flow_nominal,
m2_flow_wse_nominal=mCHW_flow_nominal,
redeclare package Medium1 = MediumCW,
redeclare package Medium2 = MediumCHW,
dp1_chi_nominal=dpCW_nominal,
dp1_wse_nominal=dpCW_nominal,
dp2_chi_nominal=dpCHW_nominal,
dp2_wse_nominal=dpCHW_nominal,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
redeclare Buildings.Fluid.Chillers.Data.ElectricEIR.ElectricEIRChiller_Trane_CVHF_2567kW_11_77COP_VSD
perChi,
k=0.4,
Ti=80,
numChi=numChi,
perPum=perPum,
addPowerToMedium=false,
show_T=true,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
reset=Buildings.Types.Reset.Parameter,
y_reset=0)
"Integrated waterside economizer on the load side of a primary-secondary chilled water system";
Modelica.Blocks.Sources.BooleanPulse tri(period=1800)
"Trigger controller reset";
parameter Buildings.Fluid.Movers.Data.Generic[numChi] perPum(each pressure=
Buildings.Fluid.Movers.BaseClasses.Characteristics.flowParameters(
V_flow=mCHW_flow_nominal/1000*{0.2,0.6,1.0,1.2}, dp=dpCHW_nominal*{1.2,1.1,
1.0,0.6})) "Pump performance data";
Buildings.Fluid.Sensors.TemperatureTwoPort TSup2(redeclare package Medium =
MediumCHW, m_flow_nominal=mCHW_flow_nominal) "Temperature sensor";
equation
connect(TSet.y, intWSEPriSec1.TSet);
connect(yVal5.y, intWSEPriSec1.yVal5);
connect(intWSEPriSec1.port_a1, sou1.ports[1]);
connect(intWSEPriSec1.port_b2, TSup1.port_a);
connect(intWSEPriSec1.port_b1, sin1.ports[1]);
connect(intWSEPriSec1.port_a2, sou2.ports[1]);
connect(yPum.y, intWSEPriSec1.yPum[1]);
connect(TEva_in.y, sou2.T_in);
connect(onChi.y, intWSEPriSec1.on[1]);
connect(onWSE.y, intWSEPriSec1.on[2]);
connect(TSet.y, intWSEPriSec2.TSet);
connect(onChi.y, intWSEPriSec2.on[1]);
connect(onWSE.y, intWSEPriSec2.on[2]);
connect(yVal5.y, intWSEPriSec2.yVal5);
connect(yPum.y, intWSEPriSec2.yPum[1]);
connect(sou1.ports[2], intWSEPriSec2.port_a1);
connect(sou2.ports[2], intWSEPriSec2.port_a2);
connect(intWSEPriSec2.port_b1, sin1.ports[2]);
connect(tri.y, intWSEPriSec2.trigger);
connect(sin2.ports[2], TSup2.port_b);
connect(TSup2.port_a, intWSEPriSec2.port_b2);
end IntegratedPrimarySecondary;
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.NonIntegrated
Non-integrated WSE in a chilled water system
Information
This example demonstrates how the model responses according to different cooling mode signals (free cooling mode, and fully mechanical cooling).
The reponses are also compared with a second case where the PI controller in the WSE is reset every 1800s.
Extends from Modelica.Icons.Example (Icon for runnable examples), Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialPlant (Partial examples for Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | mCHW_flow_nominal | 2567.1*1000/(4200*10) | Nominal mass flow rate at chilled water [kg/s] |
| MassFlowRate | mCW_flow_nominal | 2567.1*1000/(4200*8.5) | Nominal mass flow rate at condenser water [kg/s] |
| PressureDifference | dpCHW_nominal | 40000 | Nominal pressure [Pa] |
| PressureDifference | dpCW_nominal | 40000 | Nominal pressure [Pa] |
| Integer | numChi | 1 | Number of chillers |
Modelica definition
model NonIntegrated "Non-integrated WSE in a chilled water system"
extends Modelica.Icons.Example;
extends Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.BaseClasses.PartialPlant
(
sou1(nPorts=2),
sin1(nPorts=2),
TSet(k=273.15 + 5.56),
TEva_in(k=273.15 + 15.28),
onWSE(startTime=7200),
sin2(nPorts=2));
Buildings.Applications.DataCenters.ChillerCooled.Equipment.NonIntegrated nonIntWSE1(
m1_flow_chi_nominal=mCW_flow_nominal,
m2_flow_chi_nominal=mCHW_flow_nominal,
m1_flow_wse_nominal=mCW_flow_nominal,
m2_flow_wse_nominal=mCHW_flow_nominal,
redeclare package Medium1 = MediumCW,
redeclare package Medium2 = MediumCHW,
dp1_chi_nominal=dpCW_nominal,
dp1_wse_nominal=dpCW_nominal,
dp2_chi_nominal=dpCHW_nominal,
dp2_wse_nominal=dpCHW_nominal,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
redeclare Buildings.Fluid.Chillers.Data.ElectricEIR.ElectricEIRChiller_Trane_CVHF_2567kW_11_77COP_VSD
perChi,
k=0.4,
Ti=80,
numChi=numChi,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial)
"Non-integrated waterside economizer ";
Fluid.Sources.Boundary_pT sou2(
redeclare package Medium = MediumCHW,
p=MediumCHW.p_default + 50E3,
nPorts=2,
use_T_in=true) "Source on medium 2 side";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.NonIntegrated nonIntWSE2(
m1_flow_chi_nominal=mCW_flow_nominal,
m2_flow_chi_nominal=mCHW_flow_nominal,
m1_flow_wse_nominal=mCW_flow_nominal,
m2_flow_wse_nominal=mCHW_flow_nominal,
redeclare package Medium1 = MediumCW,
redeclare package Medium2 = MediumCHW,
dp1_chi_nominal=dpCW_nominal,
dp1_wse_nominal=dpCW_nominal,
dp2_chi_nominal=dpCHW_nominal,
dp2_wse_nominal=dpCHW_nominal,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
redeclare Buildings.Fluid.Chillers.Data.ElectricEIR.ElectricEIRChiller_Trane_CVHF_2567kW_11_77COP_VSD
perChi,
k=0.4,
Ti=80,
numChi=numChi,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial,
reset=Buildings.Types.Reset.Parameter,
y_reset=0) "Non-integrated waterside economizer ";
Buildings.Fluid.Sensors.TemperatureTwoPort TSup2(redeclare package Medium =
MediumCHW, m_flow_nominal=mCHW_flow_nominal) "Temperature sensor";
Modelica.Blocks.Sources.BooleanPulse tri(period=1800)
"Trigger controller reset";
equation
connect(TSet.y, nonIntWSE1.TSet);
connect(nonIntWSE1.port_a1, sou1.ports[1]);
connect(nonIntWSE1.port_b2, TSup1.port_a);
connect(nonIntWSE1.port_b1, sin1.ports[1]);
connect(nonIntWSE1.port_a2, sou2.ports[1]);
connect(TEva_in.y, sou2.T_in);
connect(onChi.y, nonIntWSE1.on[1]);
connect(onWSE.y, nonIntWSE1.on[2]);
connect(TSet.y, nonIntWSE2.TSet);
connect(onChi.y, nonIntWSE2.on[1]);
connect(onWSE.y, nonIntWSE2.on[2]);
connect(sou1.ports[2], nonIntWSE2.port_a1);
connect(sin1.ports[2], nonIntWSE2.port_b1);
connect(nonIntWSE2.port_a2, sou2.ports[2]);
connect(sin2.ports[2], TSup2.port_b);
connect(TSup2.port_a, nonIntWSE2.port_b2);
connect(tri.y, nonIntWSE2.trigger);
end NonIntegrated;
Buildings.Applications.DataCenters.ChillerCooled.Equipment.Validation.WatersideEconomizer
Validate model Buildings.Applications.DataCenters.ChillerCooled.Equipment.WatersideEconomizer
Information
This example demonstrates that the temperature at port_b2 is controlled by setting
use_controller=true.
Extends from Modelica.Icons.Example (Icon for runnable examples).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| MassFlowRate | mCHW_flow_nominal | 2567.1*1000/(4200*10) | Nominal mass flow rate at chilled water [kg/s] |
| MassFlowRate | mCW_flow_nominal | 2567.1*1000/(4200*8.5) | Nominal mass flow rate at condenser water [kg/s] |
| PressureDifference | dpCHW_nominal | 40000 | Nominal pressure [Pa] |
| PressureDifference | dpCW_nominal | 40000 | Nominal pressure [Pa] |
| Integer | numChi | 1 | Number of chillers |
Modelica definition
model WatersideEconomizer
"Validate model Buildings.Applications.DataCenters.ChillerCooled.Equipment.WatersideEconomizer"
extends Modelica.Icons.Example;
package MediumCHW = Buildings.Media.Water "Medium model";
package MediumCW = Buildings.Media.Water "Medium model";
parameter Modelica.Units.SI.MassFlowRate mCHW_flow_nominal=2567.1*1000/(4200*
10) "Nominal mass flow rate at chilled water";
parameter Modelica.Units.SI.MassFlowRate mCW_flow_nominal=2567.1*1000/(4200*
8.5) "Nominal mass flow rate at condenser water";
parameter Modelica.Units.SI.PressureDifference dpCHW_nominal=40000
"Nominal pressure";
parameter Modelica.Units.SI.PressureDifference dpCW_nominal=40000
"Nominal pressure";
parameter Integer numChi=1 "Number of chillers";
Buildings.Applications.DataCenters.ChillerCooled.Equipment.WatersideEconomizer
WSE(
redeclare package Medium1 = MediumCW,
redeclare package Medium2 = MediumCHW,
controllerType=Modelica.Blocks.Types.SimpleController.PI,
k=0.4,
Ti=80,
m1_flow_nominal=mCW_flow_nominal,
m2_flow_nominal=mCHW_flow_nominal,
eta=0.8,
dp1_nominal=dpCW_nominal,
dp2_nominal=dpCHW_nominal,
use_controller=true,
energyDynamics=Modelica.Fluid.Types.Dynamics.FixedInitial)
"Waterside economizer";
Buildings.Fluid.Sources.MassFlowSource_T sou2(
redeclare package Medium = MediumCHW,
m_flow=mCHW_flow_nominal,
nPorts=1,
use_T_in=true)
"Source on medium 2 side";
Buildings.Fluid.Sources.Boundary_pT sin1(
redeclare package Medium = MediumCW, nPorts=1)
"Sink on medium 1 side";
Buildings.Fluid.Sources.MassFlowSource_T sou1(
use_T_in=true,
redeclare package Medium = MediumCW,
m_flow=mCW_flow_nominal,
T=298.15,
nPorts=1)
"Source on medium 1 side";
Modelica.Blocks.Sources.TimeTable TCon_in(
table=[0,273.15 + 12.78;
7200,273.15 + 12.78;
7200,273.15 + 18.33;
14400,273.15 + 18.33;
14400,273.15 + 26.67],
offset=0,
startTime=0)
"Condenser inlet temperature";
Buildings.Fluid.Sources.Boundary_pT sin2(
nPorts=1,
redeclare package Medium = MediumCHW)
"Sink on medium 2 side";
Modelica.Blocks.Sources.Constant TEva_in(
k(unit="K",
displayUnit="degC")=273.15 + 25.28)
"Evaporator inlet temperature";
Modelica.Blocks.Sources.Constant TSet(
k(unit="K",
displayUnit="degC") = 273.15 + 13.56)
"Leaving chilled water temperature setpoint";
Buildings.Fluid.Sensors.TemperatureTwoPort TSup(redeclare package Medium =
MediumCHW, m_flow_nominal=mCHW_flow_nominal) "Temperature sensor";
Modelica.Blocks.Sources.BooleanStep onWSE(
startValue=true,
startTime=7200)
"On and off signal for the WSE";
equation
connect(TSet.y, WSE.TSet);
connect(WSE.port_b2, TSup.port_a);
connect(WSE.port_a2, sou2.ports[1]);
connect(TEva_in.y, sou2.T_in);
connect(TCon_in.y,sou1. T_in);
connect(sin2.ports[1], TSup.port_b);
connect(onWSE.y, WSE.on[1]);
connect(sou1.ports[1], WSE.port_a1);
connect(WSE.port_b1, sin1.ports[1]);
end WatersideEconomizer;