Buildings.Fluid.HeatExchangers.Radiators
Package with radiators models for hydronic space heating systems
Information
This package contains models for radiators that are typically found in hydronic heating systems.Extends from Modelica.Icons.VariantsPackage (Icon for package containing variants).
Package Content
| Name | Description |
|---|---|
 RadiatorEN442_2
|
Dynamic radiator for space heating |
 Examples
|
Collection of models that illustrate model use and test models |
Buildings.Fluid.HeatExchangers.Radiators.RadiatorEN442_2
Dynamic radiator for space heating
Information
This is a model of a radiator that can be used as a dynamic or steady-state model. The required parameters are data that are typically available from manufacturers that follow the European Norm EN 442-2.
However, to allow for varying mass flow rates, the transferred heat is computed using a discretization along the water flow path, and heat is exchanged between each compartment and a uniform room air and radiation temperature. This discretization is different from the computation in EN 442-2, which may yield water outlet temperatures that are below the room temperature at low mass flow rates. Furthermore, rather than using only one room temperature, this model uses a room air and room radiation temperature.
The transferred heat is modeled as follows: Let N denote the number of elements used to discretize the radiator model. For each element i ∈ {1, … , N}, the convective and radiative heat transfer Qic and Qir from the radiator to the room is
Qic = sign(Ti-Ta)
(1-fr) UA ⁄ N |Ti-Ta|n
Qir = sign(Ti-Tr)
fr UA ⁄ N |Ti-Tr|n
where Ti is the water temperature of the element, Ta is the temperature of the room air, Tr is the radiative temperature, 0 < fr < 1 is the fraction of radiant to total heat transfer, UA is the UA-value of the radiator, and n is an exponent for the heat transfer. The model computes the UA-value by numerically solving the above equations for given nominal heating power, nominal temperatures, fraction radiant to total heat transfer and exponent for heat transfer.
The parameter energyDynamics (in the Assumptions tab),
determines whether the model computes the dynamic or the steady-state response.
For the transient response, heat storage is computed using a
finite volume approach for the
water and the metal mass, which are both assumed to be at the same
temperature.
The default parameters for the heat capacities are valid for a flat plate radiator without fins, with one plate of water carying fluid, and a height of 0.42 meters.
Extends from Buildings.Fluid.Interfaces.PartialTwoPortInterface (Partial model transporting fluid between two ports without storing mass or energy), Buildings.Fluid.Interfaces.LumpedVolumeDeclarations (Declarations for lumped volumes).
Parameters
| Type | Name | Default | Description |
|---|---|---|---|
| replaceable package Medium | PartialMedium | Medium in the component | |
| Integer | nEle | 5 | Number of elements used in the discretization |
| Real | fraRad | 0.35 | Fraction radiant heat transfer |
| Real | n | 1.24 | Exponent for heat transfer |
| Nominal condition | |||
| MassFlowRate | m_flow_nominal | abs(Q_flow_nominal/cp_nomina... | Nominal mass flow rate [kg/s] |
| Power | Q_flow_nominal | Nominal heating power (positive for heating) [W] | |
| Temperature | T_a_nominal | Water inlet temperature at nominal condition [K] | |
| Temperature | T_b_nominal | Water outlet temperature at nominal condition [K] | |
| Temperature | TAir_nominal | 293.15 | Air temperature at nominal condition [K] |
| Temperature | TRad_nominal | TAir_nominal | Radiative temperature at nominal condition [K] |
| PressureDifference | dp_nominal | 0 | Pressure drop at nominal mass flow rate [Pa] |
| Transition to laminar | |||
| Real | deltaM | 0.3 | Fraction of nominal mass flow rate where transition to turbulent occurs |
| Assumptions | |||
| Boolean | allowFlowReversal | true | = false to simplify equations, assuming, but not enforcing, no flow reversal |
| Advanced | |||
| MassFlowRate | m_flow_small | 1E-4*abs(m_flow_nominal) | Small mass flow rate for regularization of zero flow [kg/s] |
| Boolean | from_dp | false | = true, use m_flow = f(dp) else dp = f(m_flow) |
| Boolean | linearized | false | = true, use linear relation between m_flow and dp for any flow rate |
| Diagnostics | |||
| Boolean | show_T | true | = true, if actual temperature at port is computed |
| Dynamics | |||
| Dynamics | massDynamics | energyDynamics | Type of mass balance: dynamic (3 initialization options) or steady state, must be steady state if energyDynamics is steady state |
| Dynamics | |||
| Conservation equations | |||
| Dynamics | energyDynamics | Modelica.Fluid.Types.Dynamic... | Type of energy balance: dynamic (3 initialization options) or steady state |
| Real | mSenFac | 1 + 500*mDry/(VWat*cp_nomina... | Factor for scaling the sensible thermal mass of the volume |
| Volume | VWat | 5.8E-6*abs(Q_flow_nominal) | Water volume of radiator [m3] |
| Mass | mDry | 0.0263*abs(Q_flow_nominal) | Dry mass of radiator that will be lumped to water heat capacity [kg] |
| Initialization | |||
| AbsolutePressure | p_start | Medium.p_default | Start value of pressure [Pa] |
| Temperature | T_start | Medium.T_default | Start value of temperature [K] |
| MassFraction | X_start[Medium.nX] | Medium.X_default | Start value of mass fractions m_i/m [kg/kg] |
| ExtraProperty | C_start[Medium.nC] | fill(0, Medium.nC) | Start value of trace substances |
| ExtraProperty | C_nominal[Medium.nC] | fill(1E-2, Medium.nC) | Nominal value of trace substances. (Set to typical order of magnitude.) |
Connectors
| Type | Name | Description |
|---|---|---|
| FluidPort_a | port_a | Fluid connector a (positive design flow direction is from port_a to port_b) |
| FluidPort_b | port_b | Fluid connector b (positive design flow direction is from port_a to port_b) |
| HeatPort_a | heatPortCon | Heat port for convective heat transfer with room air temperature |
| HeatPort_a | heatPortRad | Heat port for radiative heat transfer with room radiation temperature |
Modelica definition
model RadiatorEN442_2 "Dynamic radiator for space heating"
extends Buildings.Fluid.Interfaces.PartialTwoPortInterface(
show_T=true,
m_flow_nominal=abs(Q_flow_nominal/cp_nominal/(T_a_nominal-T_b_nominal)));
extends Buildings.Fluid.Interfaces.LumpedVolumeDeclarations(
final X_start = Medium.X_default,
final C_start = fill(0, Medium.nC),
final C_nominal = fill(1E-2, Medium.nC),
final mSenFac = 1 + 500*mDry/(VWat*cp_nominal*Medium.density(
Medium.setState_pTX(Medium.p_default, Medium.T_default, Medium.X_default))),
final massDynamics=energyDynamics);
constant Boolean homotopyInitialization = true "= true, use homotopy method";
parameter Integer nEle(min=1) = 5
"Number of elements used in the discretization";
parameter Real fraRad(min=0, max=1) = 0.35 "Fraction radiant heat transfer";
// Assumptions
parameter Modelica.Units.SI.Power Q_flow_nominal
"Nominal heating power (positive for heating)";
parameter Modelica.Units.SI.Temperature T_a_nominal
"Water inlet temperature at nominal condition";
parameter Modelica.Units.SI.Temperature T_b_nominal
"Water outlet temperature at nominal condition";
parameter Modelica.Units.SI.Temperature TAir_nominal=293.15
"Air temperature at nominal condition";
parameter Modelica.Units.SI.Temperature TRad_nominal=TAir_nominal
"Radiative temperature at nominal condition";
parameter Real n = 1.24 "Exponent for heat transfer";
parameter Modelica.Units.SI.Volume VWat=5.8E-6*abs(Q_flow_nominal)
"Water volume of radiator";
parameter Modelica.Units.SI.Mass mDry=0.0263*abs(Q_flow_nominal)
"Dry mass of radiator that will be lumped to water heat capacity";
parameter Real deltaM(min=0.01) = 0.3
"Fraction of nominal mass flow rate where transition to turbulent occurs";
parameter Boolean from_dp = false
"= true, use m_flow = f(dp) else dp = f(m_flow)";
parameter Modelica.Units.SI.PressureDifference dp_nominal(displayUnit="Pa")=
0 "Pressure drop at nominal mass flow rate";
parameter Boolean linearized = false
"= true, use linear relation between m_flow and dp for any flow rate";
// Heat flow rates
Modelica.Units.SI.HeatFlowRate QCon_flow=heatPortCon.Q_flow
"Heat input into the water due to convective heat transfer with room air";
Modelica.Units.SI.HeatFlowRate QRad_flow=heatPortRad.Q_flow
"Heat input into the water due to radiative heat transfer with room";
Modelica.Units.SI.HeatFlowRate Q_flow=QCon_flow + QRad_flow
"Heat input into the water";
// Heat ports
Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_a heatPortCon
"Heat port for convective heat transfer with room air temperature";
Modelica.Thermal.HeatTransfer.Interfaces.HeatPort_a heatPortRad
"Heat port for radiative heat transfer with room radiation temperature";
Buildings.Fluid.MixingVolumes.MixingVolume[nEle] vol(
redeclare each package Medium = Medium,
each nPorts=2,
each V=VWat/nEle,
each final m_flow_nominal = m_flow_nominal,
each final energyDynamics=energyDynamics,
each final massDynamics=energyDynamics,
each final p_start=p_start,
each final T_start=T_start,
each final X_start=X_start,
each final C_start=C_start,
each final mSenFac=mSenFac) "Volume for fluid stream";
protected
parameter Modelica.Units.SI.SpecificHeatCapacity cp_nominal=
Medium.specificHeatCapacityCp(Medium.setState_pTX(
Medium.p_default,
T_a_nominal,
Medium.X_default)) "Specific heat capacity at nominal conditions";
parameter Modelica.Units.SI.HeatFlowRate QEle_flow_nominal[nEle](each fixed=
false, each start=Q_flow_nominal/nEle)
"Nominal heating power of each element";
parameter Modelica.Units.SI.Temperature TWat_nominal[nEle](each fixed=false,
start={T_a_nominal - i/nEle*(T_a_nominal - T_b_nominal) for i in 1:nEle})
"Water temperature in each element at nominal conditions";
parameter Modelica.Units.SI.TemperatureDifference[nEle] dTRad_nominal(each
fixed=false, start={T_a_nominal - i/nEle*(T_a_nominal - T_b_nominal) -
TRad_nominal for i in 1:nEle})
"Temperature difference for radiative heat transfer at nominal conditions";
parameter Modelica.Units.SI.TemperatureDifference[nEle] dTCon_nominal(each
fixed=false, start={T_a_nominal - i/nEle*(T_a_nominal - T_b_nominal) -
TAir_nominal for i in 1:nEle})
"Temperature difference for convective heat transfer at nominal conditions";
parameter Modelica.Units.SI.ThermalConductance UAEle(
fixed=false,
min=0,
start=Q_flow_nominal/((T_a_nominal + T_b_nominal)/2 - ((1 - fraRad)*
TAir_nominal + fraRad*TRad_nominal))/nEle)
"UA value at nominal condition for each element";
final parameter Real k = if T_b_nominal > TAir_nominal then 1 else -1
"Parameter that is used to compute QEle_flow_nominal for heating or cooling mode";
Modelica.Thermal.HeatTransfer.Sources.PrescribedHeatFlow[nEle] preCon(
each final alpha=0)
"Heat input into radiator from convective heat transfer";
Modelica.Thermal.HeatTransfer.Sources.PrescribedHeatFlow[nEle] preRad(
each final alpha=0)
"Heat input into radiator from radiative heat transfer";
Modelica.Units.SI.TemperatureDifference dTCon[nEle]={heatPortCon.T - vol[i].T
for i in 1:nEle} "Temperature difference for convective heat transfer";
Modelica.Units.SI.TemperatureDifference dTRad[nEle]={heatPortRad.T - vol[i].T
for i in 1:nEle} "Temperature difference for radiative heat transfer";
Modelica.Blocks.Sources.RealExpression QCon[nEle](y={if homotopyInitialization
then homotopy(actual=(1 - fraRad) * UAEle * (heatPortCon.T - vol[i].T) *
Buildings.Utilities.Math.Functions.regNonZeroPower(
x=(heatPortCon.T - vol[i].T),
n=n - 1,
delta=0.05), simplified=(1 - fraRad) * UAEle .* abs(dTCon_nominal[i]) ^ (
n - 1) * (heatPortCon.T - vol[i].T)) else (1 - fraRad) * UAEle * (heatPortCon.T - vol[i].T) *
Buildings.Utilities.Math.Functions.regNonZeroPower(
x=(heatPortCon.T - vol[i].T),
n=n - 1,
delta=0.05) for i in 1:nEle}) "Convective heat flow rate";
Modelica.Blocks.Sources.RealExpression QRad[nEle](y={if homotopyInitialization
then homotopy(actual=fraRad * UAEle * (heatPortRad.T - vol[i].T) *
Buildings.Utilities.Math.Functions.regNonZeroPower(
x=(heatPortRad.T - vol[i].T),
n=n - 1,
delta=0.05), simplified=fraRad * UAEle * abs(dTRad_nominal[i]) ^ (n - 1)
* (heatPortRad.T - vol[i].T)) else fraRad * UAEle * (heatPortRad.T - vol[i].T) *
Buildings.Utilities.Math.Functions.regNonZeroPower(
x=(heatPortRad.T - vol[i].T),
n=n - 1,
delta=0.05) for i in 1:nEle}) "Radiative heat flow rate";
Modelica.Thermal.HeatTransfer.Sources.PrescribedHeatFlow preSumCon(
final alpha=0)
"Heat input into radiator from convective heat transfer";
Modelica.Blocks.Math.Sum sumCon(nin=nEle, k=-ones(nEle))
"Sum of convective heat flow rate";
Modelica.Blocks.Math.Sum sumRad(nin=nEle, k=-ones(nEle))
"Sum of radiative heat flow rate";
Modelica.Thermal.HeatTransfer.Sources.PrescribedHeatFlow preSumRad(
final alpha=0)
"Heat input into radiator from radiative heat transfer";
Buildings.Fluid.FixedResistances.PressureDrop res(
redeclare final package Medium = Medium,
final allowFlowReversal=allowFlowReversal,
final m_flow_nominal=m_flow_nominal,
final from_dp=from_dp,
final dp_nominal=dp_nominal,
final homotopyInitialization=homotopyInitialization,
final linearized=linearized,
final deltaM=deltaM,
final show_T=false) "Pressure drop component";
initial equation
if T_b_nominal > TAir_nominal then
assert(T_a_nominal > T_b_nominal,
"In RadiatorEN442_2, T_a_nominal must be higher than T_b_nominal.");
assert(Q_flow_nominal > 0,
"In RadiatorEN442_2, nominal power must be bigger than zero if T_b_nominal > TAir_nominal.");
else
assert(T_a_nominal < T_b_nominal,
"In RadiatorEN442_2, T_a_nominal must be lower than T_b_nominal.");
assert(Q_flow_nominal < 0,
"In RadiatorEN442_2, nominal power must be smaller than zero if T_b_nominal < TAir_nominal.");
end if;
TWat_nominal[1] = T_a_nominal - QEle_flow_nominal[1]/m_flow_nominal/
Medium.specificHeatCapacityCp(
Medium.setState_pTX(Medium.p_default, T_a_nominal, Medium.X_default));
for i in 2:nEle loop
TWat_nominal[i] = TWat_nominal[i-1] - QEle_flow_nominal[i]/m_flow_nominal/
Medium.specificHeatCapacityCp(
Medium.setState_pTX(Medium.p_default, TWat_nominal[i-1], Medium.X_default));
end for;
dTRad_nominal = TWat_nominal .- TRad_nominal;
dTCon_nominal = TWat_nominal .- TAir_nominal;
Q_flow_nominal = sum(QEle_flow_nominal);
for i in 1:nEle loop
// Use difference, TWat_nominal[i] - TRad/Air_nominal, to avoid larger system of equations
QEle_flow_nominal[i] = k * UAEle * (fraRad *
Buildings.Utilities.Math.Functions.powerLinearized(
x=k*TWat_nominal[i] - TRad_nominal,
n=n,
x0=0.1*k*(T_b_nominal-TRad_nominal)) + (1-fraRad) *
Buildings.Utilities.Math.Functions.powerLinearized(
x=k*TWat_nominal[i] - TAir_nominal,
n=n,
x0=0.1*k*(T_b_nominal-TAir_nominal)));
end for;
assert(homotopyInitialization, "In " + getInstanceName() +
": The constant homotopyInitialization has been modified from its default value. This constant will be removed in future releases.",
level = AssertionLevel.warning);
equation
connect(preCon.port, vol.heatPort);
connect(preRad.port, vol.heatPort);
connect(vol[nEle].ports[2], port_b);
for i in 1:nEle-1 loop
connect(vol[i].ports[2], vol[i+1].ports[1]);
end for;
connect(QCon.y, preCon.Q_flow);
connect(sumCon.u, QCon.y);
connect(sumCon.y, preSumCon.Q_flow);
connect(preSumCon.port, heatPortCon);
connect(QRad.y, preRad.Q_flow);
connect(QRad.y, sumRad.u);
connect(sumRad.y, preSumRad.Q_flow);
connect(preSumRad.port, heatPortRad);
connect(res.port_a, port_a);
connect(res.port_b, vol[1].ports[1]);
end RadiatorEN442_2;