Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation
Collection of validation models
Information
This package contains validation models for the classes in Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.
Note that most validation models contain simple input data which may not be realistic, but for which the correct output can be obtained through an analytic solution. The examples plot various outputs, which have been verified against these solutions. These model outputs are stored as reference data and used for continuous validation whenever models in the library change.
Package Content
| Name | Description |
|---|---|
 FreezeProtection
|
Validate model for implementing freeze protection |
| FreezeProtection_Disable
|
Validate model for disabling freeze protection |
| PlantRequests
|
Validate model for calculating the plant requests |
| ReliefDamper
|
Validate model for calculating relief damper control |
| ReliefFan
|
Validate model for controlling relief fan |
| ReliefFanGroup
|
Validate model for controlling relief fans group |
| ReturnFanAirflowTracking
|
Validate model for controlling return fan of units using return fan with airflow tracking |
| ReturnFanDirectPressure
|
Validate model for calculating return fan control with direct building pressure of multi zone VAV AHU |
| SupplyFan
|
Validate SupplyFan |
| SupplySignals
|
Validate model for controlling coil valve postion of multi zone VAV AHU |
| SupplyTemperature
|
Validate model for calculating supply air temperature of multi zone VAV AHU |
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.FreezeProtection
Validate model for implementing freeze protection
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.FreezeProtection for air handling unit serving multiple zones.
Modelica definition
model FreezeProtection
"Validate model for implementing freeze protection"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.FreezeProtection
frePro(
final buiPreCon=Buildings.Controls.OBC.ASHRAE.G36.Types.PressureControl.ReliefDamper,
final minOADes=Buildings.Controls.OBC.ASHRAE.G36.Types.OutdoorAirSection.DedicatedDampersAirflow,
final freSta=Buildings.Controls.OBC.ASHRAE.G36.Types.FreezeStat.No_freeze_stat)
"Freeze protection control";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp outDamPos(
final height=0.5,
final offset=0.1,
final duration=3600) "Outdoor air damper position";
Buildings.Controls.OBC.CDL.Reals.Sources.Constant outDamPosMin(
final k=0.1)
"Outdoor air damper minimum position";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp heaCoiPos(
final height=0.46,
final offset=0.5,
final duration=3600) "Heating coil position";
Buildings.Controls.OBC.CDL.Reals.Sources.Constant minOutDamPos(
final k=0.15)
"Minimum outdoor air damper position";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp retDamPos(
final height=0.2,
final offset=0.7,
final duration=3600) "Return air damper position";
Buildings.Controls.OBC.CDL.Logical.Sources.Pulse freRes(
final width=0.95,
final period=3600)
"Freeze protection reset";
Buildings.Controls.OBC.CDL.Logical.Not not1
"Logical not";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp supFanSpe(
final height=0.2,
final offset=0.5,
final duration=3600) "Supply fan speed";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp cooCoiPos(
final height=0.2,
final offset=0.5,
final duration=3600) "Cooling coil position";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp supTem(
final height=-4,
final offset=273.15 + 6,
final duration=3600) "Supply air temperature";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp mixTem(
final height=-5,
final offset=273.15 + 8,
final duration=3600) "Mixed air temperature";
Buildings.Controls.OBC.CDL.Reals.GreaterThreshold greThr(
final h=0.01)
"Check if the supply fan is proven on";
equation
connect(freRes.y, not1.u);
connect(outDamPosMin.y,frePro. uOutDamPosMin);
connect(outDamPos.y, frePro.uOutDam);
connect(heaCoiPos.y,frePro. uHeaCoi);
connect(minOutDamPos.y, frePro.uMinOutDam);
connect(retDamPos.y, frePro.uRetDam);
connect(supTem.y, frePro.TAirSup);
connect(not1.y, frePro.u1SofSwiRes);
connect(supFanSpe.y, frePro.uSupFan);
connect(cooCoiPos.y,frePro. uCooCoi);
connect(mixTem.y, frePro.TAirMix);
connect(supFanSpe.y, greThr.u);
connect(greThr.y, frePro.u1SupFan);
end FreezeProtection;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.FreezeProtection_Disable
Validate model for disabling freeze protection
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.FreezeProtection for air handling unit serving multiple zones, when disabling the freeze protection.
Modelica definition
model FreezeProtection_Disable
"Validate model for disabling freeze protection"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.FreezeProtection
frePro(
final have_frePro=false,
final buiPreCon=Buildings.Controls.OBC.ASHRAE.G36.Types.PressureControl.ReliefDamper,
final minOADes=Buildings.Controls.OBC.ASHRAE.G36.Types.OutdoorAirSection.DedicatedDampersAirflow,
final freSta=Buildings.Controls.OBC.ASHRAE.G36.Types.FreezeStat.No_freeze_stat)
"Freeze protection control";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp outDamPos(
final height=0.5,
final offset=0.1,
final duration=3600) "Outdoor air damper position";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp heaCoiPos(
final height=0.46,
final offset=0.5,
final duration=3600) "Heating coil position";
Buildings.Controls.OBC.CDL.Reals.Sources.Constant minOutDamPos(
final k=0.15)
"Minimum outdoor air damper position";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp retDamPos(
final height=0.2,
final offset=0.7,
final duration=3600) "Return air damper position";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp supFanSpe(
final height=0.2,
final offset=0.5,
final duration=3600) "Supply fan speed";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp cooCoiPos(
final height=0.2,
final offset=0.5,
final duration=3600) "Cooling coil position";
Buildings.Controls.OBC.CDL.Reals.GreaterThreshold greThr(
final h=0.01)
"Check if the supply fan is proven on";
equation
connect(outDamPos.y, frePro.uOutDam);
connect(heaCoiPos.y,frePro. uHeaCoi);
connect(minOutDamPos.y, frePro.uMinOutDam);
connect(retDamPos.y, frePro.uRetDam);
connect(supFanSpe.y, frePro.uSupFan);
connect(cooCoiPos.y,frePro. uCooCoi);
connect(supFanSpe.y, greThr.u);
connect(greThr.y, frePro.u1SupFan);
end FreezeProtection_Disable;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.PlantRequests
Validate model for calculating the plant requests
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.PlantRequests for air handling unit serving multiple zones.
Modelica definition
model PlantRequests
"Validate model for calculating the plant requests"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.PlantRequests plaReq
"Calculate plant request";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.PlantRequests plaReq1(
heaCoi=Buildings.Controls.OBC.ASHRAE.G36.Types.HeatingCoil.None)
"Calculate plant request";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp supTem(
final height=8,
final offset=273.15 + 15,
final duration=3600) "Supply air temperature";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp supTemSet(
final height=6,
final offset=273.15 + 14.5,
final duration=3600) "Supply air temperature setpoint";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp cooCoi(
final height=-0.3,
final offset=0.96,
final duration=3600,
startTime=1000) "Cooling coil position";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp heaCoi(
final height=-0.3,
final offset=0.96,
final duration=3600,
startTime=1000) "Heating coil position";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp supTem1(
final height=8,
final offset=273.15 + 12,
final duration=3600) "Supply air temperature";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp supTemSet1(
final height=15,
final offset=273.15 + 20,
final duration=3600) "Supply air temperature setpoint";
Buildings.Controls.OBC.CDL.Reals.Sources.Constant cooCoi1(
final k=0) "Cooling coil position";
equation
connect(supTem.y, plaReq1.TAirSup);
connect(supTemSet.y, plaReq1.TAirSupSet);
connect(cooCoi.y, plaReq1.uCooCoiSet);
connect(supTem1.y, plaReq.TAirSup);
connect(supTemSet1.y, plaReq.TAirSupSet);
connect(cooCoi1.y, plaReq.uCooCoiSet);
connect(heaCoi.y, plaReq.uHeaCoiSet);
end PlantRequests;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.ReliefDamper
Validate model for calculating relief damper control
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefDamper for actuated relief damper control without fan for systems with multiple zones.
Modelica definition
model ReliefDamper
"Validate model for calculating relief damper control"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefDamper relDam(
final k=0.1) "Relief damper control";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefDamper relDam1
"Relief damper control";
Buildings.Controls.OBC.CDL.Logical.Sources.Pulse yFan(
final period=4000) "Supply fan status";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp dpBui(
final height=40,
final offset=0,
final duration=1800) "Building static presure";
equation
connect(yFan.y, relDam.u1SupFan);
connect(dpBui.y, relDam.dpBui);
connect(yFan.y, relDam1.u1SupFan);
connect(dpBui.y, relDam1.dpBui);
end ReliefDamper;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.ReliefFan
Validate model for controlling relief fan
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefFan for controlling relief fan that is part of AHU.
Modelica definition
model ReliefFan "Validate model for controlling relief fan"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefFan
relFanCon(
final k=0.5) "Open relief damper";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefFan
relFanCon1 "Turning on relief fan";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefFan
relFanCon2 "Turning off relief fan";
Buildings.Controls.OBC.CDL.Logical.Sources.Pulse supFan(final width=0.8,
final period=3600)
"Supply fan status";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp dpBui(
final height=40,
final offset=0,
final duration=1800) "Building static presure";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp dpBui1(
final height=-15,
final offset=20,
final duration=1800,
startTime=1800)
"Building static presure";
Buildings.Controls.OBC.CDL.Logical.Sources.Constant supFan1(
final k=true)
"Supply fan status";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp dpBui2(
final height=3,
final offset=11,
final duration=1800)
"Building static presure";
equation
connect(dpBui.y, relFanCon1.dpBui);
connect(dpBui1.y, relFanCon2.dpBui);
connect(supFan.y, relFanCon.u1SupFan);
connect(supFan1.y, relFanCon1.u1SupFan);
connect(supFan1.y, relFanCon2.u1SupFan);
connect(dpBui2.y, relFanCon.dpBui);
end ReliefFan;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.ReliefFanGroup
Validate model for controlling relief fans group
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefFanGroup for relief fan group for systems with multiple zones.
Modelica definition
model ReliefFanGroup
"Validate model for controlling relief fans group"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefFanGroup
relFanCon(final k=0.5) "Relief damper control, with staging up fans";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefFanGroup
relFanCon1 "Relief damper control, with staging up fans and the fan alarm";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReliefFanGroup
relFanCon2 "Relief damper control, with the staging up and down fans";
Buildings.Controls.OBC.CDL.Logical.Sources.Pulse supFan1(
final width=1,
final period=4000)
"Supply fan status";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp dpBui(
final height=40,
final offset=0,
final duration=1800) "Building static presure";
Buildings.Controls.OBC.CDL.Logical.Sources.Pulse supFan2(
final width=1,
final period=4000,
shift=600) "Supply fan status";
Buildings.Controls.OBC.CDL.Reals.GreaterThreshold greThr[4](
final t=fill(0.01, 4))
"Check if the relief fan is proven on";
Buildings.Controls.OBC.CDL.Logical.Pre pre[4] "Return relief fan status";
Buildings.Controls.OBC.CDL.Reals.GreaterThreshold greThr1[4](
final t=fill(0.01, 4))
"Check if the relief fan is proven on";
Buildings.Controls.OBC.CDL.Logical.Pre pre1[4] "Return relief fan status";
Buildings.Controls.OBC.CDL.Integers.Sources.Constant conInt[4](
final k=fill(0, 4)) "Constant zero";
Buildings.Controls.OBC.CDL.Integers.Sources.Pulse intPul(
final amplitude=2,
final period=3600,
final offset=0) "Fan 1 alarm level";
Buildings.Controls.OBC.CDL.Discrete.ZeroOrderHold zerOrdHol[4](
final samplePeriod=fill(20, 4))
"Zero order hold";
Buildings.Controls.OBC.CDL.Discrete.ZeroOrderHold zerOrdHol1[4](
final samplePeriod=fill(20, 4))
"Zero order hold";
Buildings.Controls.OBC.CDL.Reals.GreaterThreshold greThr2[4](
final t=fill(0.01, 4))
"Check if the relief fan is proven on";
Buildings.Controls.OBC.CDL.Logical.Pre pre2[4] "Return relief fan status";
Buildings.Controls.OBC.CDL.Discrete.ZeroOrderHold zerOrdHol2[4](
final samplePeriod=fill(20, 4))
"Zero order hold";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp dpBui1(
final height=-15,
final offset=20,
final duration=1800,
startTime=1800)
"Building static presure";
equation
connect(dpBui.y, relFanCon.dpBui);
connect(dpBui.y, relFanCon1.dpBui);
connect(greThr.y, pre.u);
connect(supFan1.y, relFanCon.u1SupFan[1]);
connect(supFan2.y, relFanCon.u1SupFan[2]);
connect(supFan1.y, relFanCon1.u1SupFan[1]);
connect(supFan2.y, relFanCon1.u1SupFan[2]);
connect(pre.y, relFanCon.u1RelFan);
connect(greThr1.y, pre1.u);
connect(pre1.y, relFanCon1.u1RelFan);
connect(conInt.y, relFanCon.uRelFanAla);
connect(conInt[1].y, relFanCon1.uRelFanAla[2]);
connect(conInt[2].y, relFanCon1.uRelFanAla[3]);
connect(conInt[3].y, relFanCon1.uRelFanAla[4]);
connect(intPul.y, relFanCon1.uRelFanAla[1]);
connect(relFanCon.yRelFan, zerOrdHol.u);
connect(zerOrdHol.y, greThr.u);
connect(relFanCon1.yRelFan, zerOrdHol1.u);
connect(zerOrdHol1.y, greThr1.u);
connect(greThr2.y,pre2. u);
connect(pre2.y,relFanCon2. u1RelFan);
connect(relFanCon2.yRelFan, zerOrdHol2.u);
connect(zerOrdHol2.y,greThr2. u);
connect(dpBui1.y, relFanCon2.dpBui);
connect(supFan1.y, relFanCon2.u1SupFan[1]);
connect(supFan2.y, relFanCon2.u1SupFan[2]);
connect(conInt.y, relFanCon2.uRelFanAla);
end ReliefFanGroup;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.ReturnFanAirflowTracking
Validate model for controlling return fan of units using return fan with airflow tracking
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReturnFanAirflowTracking for return fan control with airflow tracking for systems with multiple zones.
Modelica definition
model ReturnFanAirflowTracking
"Validate model for controlling return fan of units using return fan with airflow tracking"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReturnFanAirflowTracking
retFanAirTra(final difFloSet=0.5, final k=0.1)
"Return fan control with airflow tracking";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReturnFanAirflowTracking
retFanAirTra1(final difFloSet=0.5)
"Return fan control with airflow tracking";
Buildings.Controls.OBC.CDL.Logical.Sources.Pulse yFan(width=0.75,
final period=4000) "Supply fan status";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp supFlo(
final height=1.0,
final offset=0.2,
final duration=1800) "Supply air flow rate";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp retFlo(
final height=0.4,
final offset=0.1,
final duration=1800) "Return air flow rate";
equation
connect(yFan.y, retFanAirTra.u1SupFan);
connect(yFan.y, retFanAirTra1.u1SupFan);
connect(supFlo.y, retFanAirTra.VAirSup_flow);
connect(supFlo.y, retFanAirTra1.VAirSup_flow);
connect(retFlo.y, retFanAirTra.VAirRet_flow);
connect(retFlo.y, retFanAirTra1.VAirRet_flow);
end ReturnFanAirflowTracking;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.ReturnFanDirectPressure
Validate model for calculating return fan control with direct building pressure of multi zone VAV AHU
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReturnFanDirectPressure for exhaust air damper and return fan control with direct building pressure measurement for systems with multiple zones.
Modelica definition
model ReturnFanDirectPressure
"Validate model for calculating return fan control with direct building pressure of multi zone VAV AHU"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReturnFanDirectPressure
retFanPre(
final disSpe_min=0.1,
final disSpe_max=0.9,
final k=0.1) "Return fan control with direct building pressure";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReturnFanDirectPressure
retFanPre1(
final disSpe_min=0.1,
final disSpe_max=0.9,
final k=0.5) "Return fan control with direct building pressure";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.ReturnFanDirectPressure
retFanPre2(final
disSpe_min=0.1, final disSpe_max=0.9)
"Return fan control with direct building pressure";
Buildings.Controls.OBC.CDL.Logical.Sources.Pulse yFan(
final period=4000) "Supply fan status";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp dpBui(
final height=40,
final offset=0,
final duration=1800) "Building static presure";
equation
connect(yFan.y, retFanPre.u1SupFan);
connect(dpBui.y, retFanPre.dpBui);
connect(yFan.y, retFanPre1.u1SupFan);
connect(yFan.y, retFanPre2.u1SupFan);
connect(dpBui.y, retFanPre1.dpBui);
connect(dpBui.y, retFanPre2.dpBui);
connect(yFan.y, retFanPre.u1MinOutAirDam);
connect(yFan.y, retFanPre1.u1MinOutAirDam);
connect(yFan.y, retFanPre2.u1MinOutAirDam);
end ReturnFanDirectPressure;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.SupplyFan
Validate SupplyFan
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.SupplyFan.
Modelica definition
model SupplyFan "Validate SupplyFan"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.SupplyFan conSupFan(
final Td=1,
final controllerType=Buildings.Controls.OBC.CDL.Types.SimpleController.PI,
final maxSet=400,
final k=0.001,
final Ti=10) "Block outputs supply fan speed";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.SupplyFan conSupFan1(
final have_perZonRehBox=true,
final Td=1,
final controllerType=Buildings.Controls.OBC.CDL.Types.SimpleController.PI,
final maxSet=400,
final k=0.001,
final Ti=10)
"Block outputs supply fan speed for the AHU system with reheat boxes on perimeter zones";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.SupplyFan conSupFan2(
final Td=1,
final controllerType=Buildings.Controls.OBC.CDL.Types.SimpleController.PI,
final maxSet=400,
final k=0.001,
final Ti=10)
"Block outputs supply fan speed for the unit with airflow measurement station";
protected
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp ram(
final duration=28800,
final height=6) "Ramp signal for generating operation mode";
Buildings.Controls.OBC.CDL.Reals.Sources.Sin sine(
final freqHz=1/14400,
final offset=3,
final amplitude=2)
"Generate sine signal ";
Buildings.Controls.OBC.CDL.Reals.Sources.Sin sine1(
final freqHz=1/14400,
final offset=200,
amplitude=150)
"Generate sine signal";
Buildings.Controls.OBC.CDL.Reals.Abs abs
"Block generates absolute value of input";
Buildings.Controls.OBC.CDL.Reals.Abs abs1
"Block generates absolute value of input";
Buildings.Controls.OBC.CDL.Reals.Round round2(
final n=0)
"Round real number to given digits";
Buildings.Controls.OBC.CDL.Conversions.RealToInteger reaToInt1
"Convert real to integer";
Buildings.Controls.OBC.CDL.Conversions.RealToInteger reaToInt2
"Convert real to integer";
Buildings.Controls.OBC.CDL.Reals.Round round1(n=0)
"Round real number to given digits";
equation
connect(sine1.y, conSupFan.dpDuc);
connect(sine.y, abs1.u);
connect(ram.y, abs.u);
connect(abs1.y, round2.u);
connect(round2.y, reaToInt1.u);
connect(reaToInt1.y, conSupFan.uZonPreResReq);
connect(abs.y, round1.u);
connect(round1.y, reaToInt2.u);
connect(reaToInt2.y, conSupFan.uOpeMod);
connect(reaToInt2.y, conSupFan2.uOpeMod);
connect(reaToInt1.y, conSupFan2.uZonPreResReq);
connect(sine1.y, conSupFan2.dpDuc);
connect(reaToInt2.y, conSupFan1.uOpeMod);
connect(reaToInt1.y, conSupFan1.uZonPreResReq);
connect(sine1.y, conSupFan1.dpDuc);
end SupplyFan;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.SupplySignals
Validate model for controlling coil valve postion of multi zone VAV AHU
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.SupplySignals for a change of the supply air temperature setpoint, measured supply air temperature and the supply fan status, to specify coil valve positions, and generate control loop signal.
Modelica definition
model SupplySignals
"Validate model for controlling coil valve postion of multi zone VAV AHU"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.SupplySignals supSig
"Output valve position and supply air temperature control loop signal";
Buildings.Controls.OBC.CDL.Logical.Sources.Pulse supFanSta(period=7200)
"Supply fan status";
Buildings.Controls.OBC.CDL.Reals.Sources.Pulse TSup(
final amplitude=14,
final period=7200,
final offset=10 + 273.15)
"Supply air temperature";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp TSupSet(
final height=3,
final duration=7200,
final offset=15 + 273.15)
"Supply air temperature setpoint";
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.SupplySignals supSig1
"Output valve position and supply air temperature control loop signal";
Buildings.Controls.OBC.CDL.Logical.Sources.Constant fanOn(
final k=true) "Fan on";
equation
connect(TSupSet.y, supSig.TAirSupSet);
connect(TSup.y, supSig.TAirSup);
connect(supFanSta.y, supSig.u1SupFan);
connect(TSupSet.y, supSig1.TAirSupSet);
connect(TSup.y, supSig1.TAirSup);
connect(fanOn.y, supSig1.u1SupFan);
end SupplySignals;
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.Validation.SupplyTemperature
Validate model for calculating supply air temperature of multi zone VAV AHU
Information
This example validates Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.SupplyTemperature for a change of outdoor temperature, operation mode, supply fan status, maximum supply temperature, to specify the supply air temperature for systems with multiple zones.
Modelica definition
model SupplyTemperature
"Validate model for calculating supply air temperature of multi zone VAV AHU"
Buildings.Controls.OBC.ASHRAE.G36.AHUs.MultiZone.VAV.SetPoints.SupplyTemperature
conTSupSet
"Supply air temperature setpoint for multi zone system";
Buildings.Controls.OBC.CDL.Reals.Sources.Sin outTem(
final amplitude=5,
final freqHz=1/86400,
final offset=18 + 273.15) "Outdoor air temperature";
Buildings.Controls.OBC.CDL.Logical.Sources.Pulse supFanSta(
final period=43200)
"Supply fan status";
Buildings.Controls.OBC.CDL.Reals.Sources.Ramp opeMod(
final offset=1,
final height=1,
final duration=90000) "Operation mode";
Buildings.Controls.OBC.CDL.Reals.Abs abs
"Block generates absolute value of input";
Buildings.Controls.OBC.CDL.Reals.Sources.Sin sine(
final amplitude=6,
final freqHz=1/86400)
"Block generates sine signal";
Buildings.Controls.OBC.CDL.Conversions.RealToInteger reaToInt1
"Convert real to integer";
Buildings.Controls.OBC.CDL.Reals.Round round1(
final n=0)
"Round real number to given digits";
Buildings.Controls.OBC.CDL.Conversions.RealToInteger reaToInt2
"Convert real to integer";
Buildings.Controls.OBC.CDL.Reals.Round round2(
final n=0)
"Round real number to given digits";
equation
connect(supFanSta.y, conTSupSet.u1SupFan);
connect(outTem.y, conTSupSet.TOut);
connect(sine.y, abs.u);
connect(opeMod.y, round2.u);
connect(round2.y, reaToInt2.u);
connect(abs.y, round1.u);
connect(round1.y, reaToInt1.u);
connect(reaToInt1.y, conTSupSet.uZonTemResReq);
connect(reaToInt2.y, conTSupSet.uOpeMod);
end SupplyTemperature;